/***************************************************************************************************************************************
說明:
SH88F516集成了3個8位PWM模塊,可以分別通過各自的PWMCON寄存器控制PWM模塊的時鐘,PWMP寄存器控制PWM輸出波形的周期,PWMD寄存器控制PWM輸出波形的
占空比,從而產生周期和占空比分別可調整的脈寬調制波形.在PWM輸出允許期間可以修改這三個寄存器,但在下一個PWM周期修改才會起作用.	PWM定時器提
供3個中斷源,在每個PWM周期都會產生中斷.他們有不同的標志位,共享一個中斷向量地址.
本程序通過PWM0中斷和查表的方式輸出50Hz正弦波,示波器測量時,J9右端測量,左端接地,
要求;打開J13的1腳 
****************************************************************************************************************************************/
#include <sh88f516.h>

/*unsigned char code SPWM[200]={50,52,53,55,56,58,59,61,62,64,65,67,68,70,71,73,74,
								75,77,78,79,81,82,83,84,85,86,88,89,90,90,91,92,93,
								94,95,95,96,96,97,98,98,98,99,99,99,100,100,100,100,
								100,100,100,100,100,99,99,99,98,98,98,97,96,96,95,95,
								94,93,92,91,90,90,89,88,86,85,84,83,82,81,79,78,77,
								75,74,73,71,70,68,67,65,64,62,61,59,58,56,55,53,52,
								50,48,47,45,44,42,41,39,38,36,35,33,32,30,29,27,26,
								25,23,22,21,19,18,17,16,15,14,12,11,10,10,9,8,7,6,5,
								5,4,4,3,2,2,2,1,1,1,0,0,0,0,0,0,0,0,0,1,1,1,2,2,2,3,
								4,4,5,5,6,7,8,9,10,10,11,12,14,15,16,17,18,19,21,22,
								23,25,26,27,29,30,32,33,35,36,38,39,41,42,44,45,47,48};

*/

unsigned char SpwmCount;
void init();



main()
{
		int i,j;
		P1 = 0xff;
	init();
					
    while(1) 
	
	{

	for (i=500; i>0; i--)
	{
	
	P1 |= 0x0f;

	}
	for (j=500; j>0; j--)
	{
	P1 &= 0x00;
	}
	 }

}

  

void init()
{

	CLKCON = 0x00;			//系統時鐘=晶振頻率

	PWM0P = 2;			//PWM0輸出周期   = PWM0P[7-0]*PWM0時鐘
	PWM0D = 1;			    //PWM0輸出占空比 = PWM0D[7-0]*PWM0時鐘		  50%
	PWM0CON = 0x81;			//PWM0控制寄存器; 1011 0001---打開PWM0定時器,并從PWM0管腳輸出  占空比極性為高,時鐘為系統時鐘的1/16

	IEN1 = 0x20;			//開啟PWM中斷  EPWM=1 但是這邊不能使用位操作,不具備位尋址功能
	EA = 1;					//開啟總中斷

	SpwmCount = 0;

}



void PWM_INT() interrupt 12  using 3  //PWM 0/1/2的中斷號共享為12.
{

/*	if(PWM0CON & 0x02)				  //判斷是否為PWM1中斷?
	{
		 SpwmCount++;
		 if(SpwmCount>=200)
		     SpwmCount=0;
		
		
		PWM0D = 1; //SPWM[SpwmCount];	  //查表得到相應的正弦值

	}

 */
//	PWM0CON &= 0xFD;			      //清除中斷標志位	PWMIF=0但是這邊不能使用位操作,不具備位尋址功能

}