?? si4432.c
字號:
/*
** ============================================================================
**
** FILE
** Si4432.c
**
** DESCRIPTION
** Contains all Si4432 RF functions
**
** CREATED
** Silicon Laboratories Hungary Ltd
**
** COPYRIGHT
** Copyright 2009 Silicon Laboratories, Inc.
** http://www.silabs.com
**
** ============================================================================
*/
#include "S8051.h"
#include "Si4432.h"
#include "uart.h"
/*------------------------------------------------------------------------*/
/* GLOBAL variables */
/*------------------------------------------------------------------------*/
code uint8 RMRfSettings[NMBR_OF_SAMPLE_SETTING1][NMBR_OF_PARAMETER] =
{
//revB1
// IFBW, COSR, CRO2, CRO1, CRO0, CTG1, CTG0, TDR1, TDR0, MMC1, FDEV, AFC, AFCTimingControl, AFCLimiter
{0x1D, 0x41, 0x60, 0x27, 0x52, 0x00, 0x05, 0x13, 0xa9, 0x20, 0x3a, 0x40, 0x0A, 0x20}, //DR: 2.4kbps, DEV: +-36kHz, BBBW: 75.2kHz (crystal:20 ppm)
{0x1D, 0xA1, 0x20, 0x4E, 0xA5, 0x00, 0x0A, 0x27, 0x52, 0x20, 0x48, 0x40, 0x0A, 0x20}, //DR: 4.8kbps, DEV: +-45kHz, BBBW: 95.3kHz (crystal:20 ppm)
{0x1E, 0xD0, 0x00, 0x9D, 0x49, 0x00, 0x24, 0x4e, 0xa5, 0x20, 0x48, 0x40, 0x0A, 0x20}, //DR: 9.6kbps, DEV: +-45kHz, BBBW: 112.8kHz (crystal:20 ppm)
{0x03, 0xD0, 0x00, 0x9D, 0x49, 0x01, 0x3D, 0x9D, 0x49, 0x20, 0x0F, 0x40, 0x0A, 0x1E}, //DR: 19.2kbps, DEV: +-9.6kHz, BBBW: 75.2kHz (crystal:20 ppm)
{0x03, 0x68, 0x01, 0x3A, 0x93, 0x02, 0x78, 0x09, 0xD5, 0x00, 0x1F, 0x40, 0x0A, 0x20}, //DR: 38.4kbps, DEV: +-19.2kHz, BBBW: 83.2kHz (crystal:20 ppm)
{0x06, 0x45, 0x01, 0xD7, 0xDC, 0x03, 0xB8, 0x0E, 0xBF, 0x00, 0x2E, 0x40, 0x0A, 0x2D}, //DR: 57.6kbps, DEV: +-28.8kHz, BBBW: 124.6kHz (crystal:20 ppm)
{0x82, 0x68, 0x01, 0x3A, 0x93, 0x02, 0x78, 0x1D, 0x7E, 0x00, 0x5C, 0x40, 0x0A, 0x50}, //DR: 115.2kbps, DEV: +-57.6kHz, BBBW: 172.8kHz (crystal:20 ppm)
};
code uint8 CMRfSettings[NMBR_OF_SAMPLE_SETTING2][NMBR_OF_PARAMETER] =
{
//revB1
// IFBW, COSR, CRO2, CRO1, CRO0, CTG1, CTG0, TDR1, TDR0, MMC1, FDEV, AFC, AFCTimingControl, AFCLimiter
{0x9A, 0x71, 0x40, 0x34, 0x6E, 0x00, 0x08, 0x4e, 0x79, 0x20, 0x90, 0x40, 0x0A, 0x41}, //DR: 9.6kbps, DEV: +-90kHz, BBBW:208.4kHz (crystal: 20ppm)
};
#ifdef BAND_434
//parameters of the frequency setting
code uint8 FreqSettings[4][7] =
{
// 2.4kbps, 4.8kbps, 9.6kbps, 19.2kbps, 38.4kbps 57.6kbps 115.2kbps
{4, 4, 4, 3, 3, 2, 1 }, //max channel number
{0x53, 0x53, 0x53, 0x58, 0x56, 0x5A, 0x61 }, //start freq. reg1
{0x40, 0x40, 0x40, 0x40, 0xC0, 0x40, 0xC0 }, //start freq. reg2
{33, 33, 33, 39, 45, 36, 0 }, //freq. step
};
#endif
#ifdef BAND_470
//parameters of the frequency setting
code uint8 FreqSettings[4][7] =
{
// 2.4kbps, 4.8kbps, 9.6kbps, 19.2kbps, 38.4kbps 57.6kbps 115.2kbps
{39, 39, 39, 39, 39, 39, 39 }, //max channel number
{0x19, 0x19, 0x19, 0x19, 0x19, 0x19, 0x19 }, //start freq. reg1
{0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 }, //start freq. reg2
{100, 100, 100, 100, 100, 100, 100 }, //freq. step
};
#endif
#ifdef BAND_868
//parameters of the frequency setting
code uint8 FreqSettings[4][7] =
{
// 2.4kbps, 4.8kbps, 9.6kbps, 19.2kbps, 38.4kbps 57.6kbps 115.2kbps
{14, 14, 14, 11, 10, 8, 6 }, //max channel number
{0x2C, 0x2C, 0x2C, 0x2E, 0x2D, 0x2E, 0x32 }, //start freq. reg1
{0x60, 0x60, 0x60, 0x40, 0x40, 0xE0, 0x00 }, //start freq. reg2
{45, 45, 45, 55, 64, 78, 100 }, //freq. step
};
#endif
#ifdef BAND_915
//parameters of the frequency setting
code uint8 FreqSettings[4][7] =
{
// 2.4kbps, 4.8kbps, 9.6kbps, 19.2kbps, 38.4kbps 57.6kbps 115.2kbps
{60, 60, 60, 52, 45, 37, 29 }, //max channel number
{0x0A, 0x0A, 0x0A, 0x0A, 0x0A, 0x0A, 0x0A}, //start freq. reg1
{0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80}, //start freq. reg2
{48, 48, 48, 55, 64, 78, 100 }, //freq. step
};
#endif
#ifdef BAND_950
//parameters of the frequency setting
code uint8 FreqSettings[4][7] =
{
// 2.4kbps, 4.8kbps, 9.6kbps, 19.2kbps, 38.4kbps 57.6kbps 115.2kbps
{24, 24, 24, 24, 24, 24, 12 }, //max channel number
{0x8A, 0x8A, 0x8A, 0x8A, 0x8A, 0x8A, 0x8A}, //start freq. reg1
{0xC0, 0xC0, 0xC0, 0xC0, 0xC0, 0xC0, 0xC0}, //start freq. reg2
{20, 20, 20, 20, 20, 40, 40 }, //freq. step
};
#endif
extern xdata uint8 rf_ch;
extern xdata uint8 rf_pwr;
extern xdata uint8 rf_dr;
extern xdata uint8 mode;
/*+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+
+ FUNCTION NAME: void RfInitHw(void)
+
+ DESCRIPTION: initializes the used I/O pins, SPI and timer peripherals,
+ IT routines needed for the RF stack
+
+ RETURN: None
+
+ NOTES: 1.) has to be called in the power-on routine
+
+
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++*/
RF_ENUM RfInitHw(void)
{
xdata uint8 i;
xdata uint16 j;
//initialize I/O port directions
RF_NSEL_PIN = 1;
RF_PWRDN_PIN = 0;
//After set the RF_PWRDN_PIN to zero, need some time to wait ( ~15 ms)
for(i=0;i<15;i++)
for(j=0;j<35000;j++);
SpiReadWriteWord(InterruptStatus1 << 8);
SpiReadWriteWord(InterruptStatus2 << 8);
//SW reset
SpiWriteAddressData((REG_WRITE | OperatingFunctionControl1), 0x80);
//wait until the POR interrupt is occured
while(RF_NIRQ_PIN == 1);
SpiReadWriteWord(InterruptStatus1 << 8);
SpiReadWriteWord(InterruptStatus2 << 8);
//wait until the chip ready interrupt is occured
while(RF_NIRQ_PIN == 1);
SpiReadWriteWord(InterruptStatus1 << 8);
SpiReadWriteWord(InterruptStatus2 << 8);
//disable all the interrupts
SpiWriteAddressData((REG_WRITE | InterruptEnable1), 0x00);
SpiWriteAddressData((REG_WRITE | InterruptEnable2), 0x02);
//set cap. bank
SpiWriteAddressData((REG_WRITE | CrystalOscillatorLoadCapacitance), 0x6D);
//reset digital testbus, disable scan test
SpiWriteAddressData((REG_WRITE | DigitalTestBus), 0x00);
//select nothing to the Analog Testbus
SpiWriteAddressData((REG_WRITE | AnalogTestBus), 0x0B);
//set frequency
SpiWriteAddressData((REG_WRITE | FrequencyBandSelect), FREQ_BAND_SELECT);
set_frq(rf_ch);
//disable RX-TX headers,
SpiWriteAddressData((REG_WRITE | HeaderControl1), 0x00 );
SpiWriteAddressData((REG_WRITE | HeaderControl2), 0x02 );
SpiWriteAddressData((REG_WRITE | SyncWord3), 0x2D);
SpiWriteAddressData((REG_WRITE | SyncWord2), 0xD4);
//enable packet handler( no CRC )
SpiWriteAddressData((REG_WRITE | DataAccessControl), 0x88);
//set GFSK modulation and FIFO mode
SpiWriteAddressData((REG_WRITE | ModulationModeControl2), 0x63);
//set preamble length & detection threshold
SpiWriteAddressData((REG_WRITE | PreambleLength), (PREAMBLE_LENGTH << 1));
SpiWriteAddressData((REG_WRITE | PreambleDetectionControl), (( PD_LENGTH << 4)|0x02));
//set GPIO0 to GND
SpiWriteAddressData((REG_WRITE | GPIO0Configuration), 0x14);
//set GPIO1 & GPIO2 to control the TRX switch
SpiWriteAddressData((REG_WRITE | GPIO1Configuration), 0x12);
SpiWriteAddressData((REG_WRITE | GPIO2Configuration), 0x15);
set_pwr(rf_pwr);
RFSetRfParameters(rf_dr);
return RF_OK;
}
/*+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+
+ FUNCTION NAME: RF_ENUM RFSetRfParameters(RF_SAMPLE_SETTINGS setting)
+
+ DESCRIPTION: this function configures the RF part of the chip (both TX and RX)
+ for different (predefined) data rate, deviation and modulation index
+ requirements.
+
+
+ RETURN: RF_OK: the operation was succesfull
+ RF_ERROR_PARAMETER: invalid parameter, the operation is ignored.
+
+ NOTES:
+
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++*/
RF_ENUM RFSetRfParameters(RF_SAMPLE_SETTINGS setting)
{
if (mode == 0)
{
//set the registers according the selected RF settings in the range mode
SpiWriteAddressData((REG_WRITE | IFFilterBandwidth), RMRfSettings[setting][0] );
SpiWriteAddressData((REG_WRITE | ClockRecoveryOversamplingRatio), RMRfSettings[setting][1]);
SpiWriteAddressData((REG_WRITE | ClockRecoveryOffset2), RMRfSettings[setting][2]);
SpiWriteAddressData((REG_WRITE | ClockRecoveryOffset1), RMRfSettings[setting][3]);
SpiWriteAddressData((REG_WRITE | ClockRecoveryOffset0), RMRfSettings[setting][4]);
SpiWriteAddressData((REG_WRITE | ClockRecoveryTimingLoopGain1), RMRfSettings[setting][5]);
SpiWriteAddressData((REG_WRITE | ClockRecoveryTimingLoopGain0), RMRfSettings[setting][6]);
SpiWriteAddressData((REG_WRITE | TXDataRate1), RMRfSettings[setting][7]);
SpiWriteAddressData((REG_WRITE | TXDataRate0), RMRfSettings[setting][8]);
SpiWriteAddressData((REG_WRITE | ModulationModeControl1), RMRfSettings[setting][9]);
SpiWriteAddressData((REG_WRITE | FrequencyDeviation), RMRfSettings[setting][10]);
SpiWriteAddressData((REG_WRITE | AFCLoopGearshiftOverride), RMRfSettings[setting][11]);
SpiWriteAddressData((REG_WRITE | AFCTimingControl), RMRfSettings[setting][12]);
SpiWriteAddressData((REG_WRITE | AFCLimiter), RMRfSettings[setting][13]);
}
else
{
//set the registers according the selected RF settings in the compatible mode
SpiWriteAddressData((REG_WRITE | IFFilterBandwidth), CMRfSettings[setting][0] );
SpiWriteAddressData((REG_WRITE | ClockRecoveryOversamplingRatio), CMRfSettings[setting][1]);
SpiWriteAddressData((REG_WRITE | ClockRecoveryOffset2), CMRfSettings[setting][2]);
SpiWriteAddressData((REG_WRITE | ClockRecoveryOffset1), CMRfSettings[setting][3]);
SpiWriteAddressData((REG_WRITE | ClockRecoveryOffset0), CMRfSettings[setting][4]);
SpiWriteAddressData((REG_WRITE | ClockRecoveryTimingLoopGain1), CMRfSettings[setting][5]);
SpiWriteAddressData((REG_WRITE | ClockRecoveryTimingLoopGain0), CMRfSettings[setting][6]);
SpiWriteAddressData((REG_WRITE | TXDataRate1), CMRfSettings[setting][7]);
SpiWriteAddressData((REG_WRITE | TXDataRate0), CMRfSettings[setting][8]);
SpiWriteAddressData((REG_WRITE | ModulationModeControl1), CMRfSettings[setting][9]);
SpiWriteAddressData((REG_WRITE | FrequencyDeviation), CMRfSettings[setting][10]);
SpiWriteAddressData((REG_WRITE | AFCLoopGearshiftOverride), CMRfSettings[setting][11]);
SpiWriteAddressData((REG_WRITE | AFCTimingControl), CMRfSettings[setting][12]);
SpiWriteAddressData((REG_WRITE | AFCLimiter), CMRfSettings[setting][13]);
}
return RF_OK;
}
/*+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+
+ FUNCTION NAME: RF_ENUM RFIdle(void)
+
+ DESCRIPTION: sets the transceiver and the RF stack into IDLE state,
+ independently of the actual state of the RF stack.
+
+ RETURN: RF_OK: the operation was succesfull
+
?? 快捷鍵說明
復制代碼
Ctrl + C
搜索代碼
Ctrl + F
全屏模式
F11
切換主題
Ctrl + Shift + D
顯示快捷鍵
?
增大字號
Ctrl + =
減小字號
Ctrl + -