/* sndsEnd.c - SNDS END network interface driver for Ethernet */

/* Copyright 1984-1997 Wind River Systems, Inc. */
#include "copyright_wrs.h"

/*
modification history
--------------------
01f,25nov99,knp, changed the name from "end" to "secEnd"
01e,12nov99,knp, Corrected handling EIOCSFLAGS, added IFF_MULTICAST flag
01d,06nov99,knp, updated multicast address support
01c,18oct99,knp added polled mode support
01b,27sep99,nb  added documentation
01a,20sep99,nts&knp  adapted from WRS template
*/

/*
DESCRIPTION

This module implements the Enhanced Ethernet driver for Samsung SNDS100 Ver 1.0
Evaluation Board for their KS32C50100 microcontroller.

KS32C50100 is an ARM based processor with several integrated peripherals.
It has an interrupt controller, two 32-bit timers, one Ethernet controller,
two HDLC controllers, one IIC controller, general purpose I/O ports, and a 
2-channel DMA controller.

The built-in Ethernet controller consists of 10/100 Ethernet MAC with MII
interface to an external PHY device and a Buffered DMA controller for
transferring data to and from the memory.  The SNDS100 board has a Level One
LXT970 Ethernet PHY device that supports both 10Base-T and 100Base-T
Ethernet.

All the internal registers of the Ethernet MAC and BDMA controller are
accessible as 32-bit integers at the internal system register addresses as
defined in the KS32C50100 Microcontroller User's Manual.  The register 
addresses are defined in sndsend.h include file.

The driver requires several target-specific values provided as an input 
string to the load routine.  These target-specific values and the external 
support routines are described below.

This network interface driver does not include support for trailer protocols
or data chaining.  However, buffer loaning has been implemented in an effort 
to boost performance.

This driver maintains cache coherency by setting the Address bit 26 (A26) of
descriptor and buffer addresses.  KS32C50100 accesses all memory locations
with A26 set in a non-cached mode.  However, A26 is not used for accessing
the memory.  See the KS32C50100 Microcontroller User's Manual for details.
Because of this feature, allocating buffer space using the cacheDmaMalloc()
routine is not required.

BOARD LAYOUT
This device is on-chip.  No jumpering diagram is necessary.

EXTERNAL INTERFACE
This driver provides the standard END external interface.  The only external
interface is the sndsEndLoad() routine.  The parameters are passed
into the sndsEndLoad() function as a single colon-delimited string.
The sndsEndLoad() function uses strtok() to parse the string, which it 
expects to be of the following format:

<unit>:<speed>:<duplex>:<autoneg>

TARGET-SPECIFIC PARAMETERS

.IP <unit>
A convenient holdover from the former model.  This parameter is used only
in the string name for the driver.  Value must be 0

.IP <speed>
Indicates the desired network speed.  Valid values are 10 and 100.  This
parameter is ignored if auto-negotiation is enabled.  See below.

.IP "<duplex>"
Indicates the desired duplex mode of operation.  A value 1 indicates full-
duplex and a value 0 indicated half duplex.  This parameter is ignored if
auto-negotiation is enabled.

.IP "<auto-neg>"
Indicates whether auto-negotiation has to be enabled or not.  A value of 1
indicates that auto-negotiation should be enabled.  A value of 0 indicates
that it should be disabled.  If auto-negotiation is enabled, the speed and
duplex values are ignored.

.LP

SYSTEM RESOURCE USAGE
When implemented, this driver requires the following system resources:

    - one mutual exclusion semaphore
    - four interrupt vectors

The driver allocates the memory to share with the Ethernet device unit.
It does so by calling the calloc() routine.  As a default, 64 transmit 
descriptors (size=16 bytes), 64 transmit buffers (size=END_BUFSIZ), and
64 receive descriptors (size=16 bytes) are allocated.  TX_FD_NUM and RX_FD_NUM
macros define the number of descriptors allocated.

As a default, 128 MBLK structures, 128 CLBLK structures and 128 clusters
(size=2048) are allocated in the net pool.  END_MBLK_NUM and END_CL_NUM 
macros define the number of structures allocated.

The macros SYS_INT_CONNECT, SYS_INT_DISCONNECT, and SYS_INT_ENABLE allow
the driver to be customized for BSPs that use special versions of these
routines.

The macro SYS_INT_CONNECT is used to connect the interrupt handler to
the appropriate vector.  By default it is the routine intConnect().

The macro SYS_INT_DISCONNECT is used to disconnect the interrupt handler prior
to unloading the module.  By default this is a dummy routine that
returns OK.

The macro SYS_INT_ENABLE is used to enable the interrupt level for the
end device.  It is called once during initialization.  By default this is
the routine intEnable().

The macro SYS_ENET_ADDR_GET is used to get the ethernet address (MAC)
for the device.  The single argument to this routine is the END_DEVICE
pointer.  By default this routine copies the ethernet address stored in
the global variable sndsEndEnetAddr defined in sndsend.h into the 
END_DEVICE structure.  The global variable has to be changed for changing
the MAC address of the Ethernet port.

SPECIAL CONSIDERATION

The MAC address of Ethernet port is hard-coded in the global array named
sndsEndEnetAddr defined in sndsEnd.h

The internal registers of MAC and BDMA controllers in the KS32C50100
microcontroller are accessible as 32-bit integers at pre-defined address
locations.  Hence separate macros are not provided for register accesses.
All through the driver code, these registers are accessed directly.

INCLUDES:
end.h endLib.h etherMultiLib.h sndsend.h

SEE ALSO: muxLib, endLib
.I "Writing and Enhanced Network Driver"
*/

/* includes */

#include "vxWorks.h"
#include "sndsEnd.h"			/* mod knp 7sep99"drv/end/sndsEnd.h"Common defines. */
#include "etherMultiLib.h"		/* multicast stuff. */
#include "end.h"			/* Common END structures. */
#include "endLib.h"
#include "lstLib.h"			/* Needed to maintain protocol list. */
#include "cacheLib.h"
#include "stdlib.h"
#include "stdio.h"
#include "intLib.h"
#include "iv.h"
#include "netLib.h"
#include "config.h"

/* defines */

/* Configuration items */
#define ENET_HDR_REAL_SIZ 	14
#define END_BUFSIZ      	(ETHERMTU + ENET_HDR_REAL_SIZ + 6)
#define END_SPEED        	10000000
#define	SNDS_CL_SIZE		2048
#define	RX_FD_NUM			64
#define	TX_FD_NUM			64

#define LS_POLLING          0x20

/*
 * Default macro definitions for BSP interface.
 * These macros can be redefined in a wrapper file, to generate
 * a new module with an optimized interface.
 */

/* Macro to connect interrupt handler to vector */

#ifndef SYS_INT_CONNECT
#   define SYS_INT_CONNECT(pDrvCtrl,rtn,arg,pResult) \
	{ \
	IMPORT STATUS sysIntConnect(); \
	*pResult = intConnect ((VOIDFUNCPTR *)INUM_TO_IVEC (pDrvCtrl->ivec), \
			     rtn, (int)arg); \
	}
#endif

/* Macro to disconnect interrupt handler from vector */

#ifndef SYS_INT_DISCONNECT
#   define SYS_INT_DISCONNECT(pDrvCtrl,rtn,arg,pResult) \
	{ \
	*pResult = OK; /* HELP: need a real routine */ \
	}
#endif

/* Macro to enable the appropriate interrupt level */

#ifndef SYS_INT_ENABLE
#define SYS_INT_ENABLE(pDrvCtrl) \
	{ \
	IMPORT void sysLanIntEnable(); \
	sysLanIntEnable (pDrvCtrl->ilevel); \
	}
#endif

/* Macro to get the ethernet address from the BSP */

#ifndef SYS_ENET_ADDR_GET
#   define SYS_ENET_ADDR_GET(pDevice) \
	{ \
	IMPORT unsigned char sndsEndEnetAddr[]; \
	bcopy ((char *)sndsEndEnetAddr, (char *)(&pDevice->enetAddr), 6); \
	}
#endif

/*
 * Macros to do a short (UINT16) access to the chip. Default
 * assumes a normal memory mapped device.
 */

#ifndef SNDS_OUT_SHORT
#   define SNDS_OUT_SHORT(pDrvCtrl,addr,value) \
	(*(USHORT *)addr = value)
#endif

#ifndef SNDS_IN_SHORT
#   define SNDS_IN_SHORT(pDrvCtrl,addr,pData) \
	(*pData = *addr)
#endif

#ifndef SNDS_OUT_LONG
#   define SNDS_OUT_LONG(pDrvCtrl,addr,value) \
	(*(UINT32 *)addr = value)
#endif

#ifndef SNDS_IN_LONG
#   define SNDS_IN_LONG(pDrvCtrl,addr,pData) \
	(*pData = *addr)
#endif

/*A shortcut for getting the hardware address from the MIB II stuff. */


#define END_HADDR(pEnd)	\
		((pEnd)->mib2Tbl.ifPhysAddress.phyAddress)

#define END_HADDR_LEN(pEnd) \
		((pEnd)->mib2Tbl.ifPhysAddress.addrLength)

/* typedefs */

typedef struct free_args
    {
    void* arg1;
    void* arg2;
    } FREE_ARGS;

/* The definition of the driver control structure */

typedef struct end_device
    {
	END_OBJ    	end;			/* The class we inherit from. */
    int			unit;			/* unit number */
 	int			ivecBdmaTx;		/* bdmaTx interrupt vector */
	int			ivecBdmaRx;		/* bdmaRx interrupt vector */
	int			ivecMacTx;		/* macTx  interrupt vector */
	int			ivecMacRx;		/* macRx  interrupt vector */
    long		flags;			/* Our local flags. */
    UCHAR		enetAddr[6];	/* ethernet address */
	UCHAR		netSpeed;		/* 10 or 100 */
	UCHAR		duplexMode;		/* HDX = 0. FDX = 1 */
	UCHAR		autoNeg;		/* 1 = autoneg enabled */
	BOOL		fdInitialized;	/* Set to TRUE after FD allocation */
	ETHER_STATISTICS	statistics;	/* Ethernet statistics counters */
	UINT32	addrList[32];	/* Array for storing addresses Max = 21, i.e. 32 long words */
	UINT32	mcastAddrCount;	/* Number of valid multicast addresses */
    } END_DEVICE;

/* globals*/

/*
 * This will only work if there is only a single unit, for multiple
 * unit device drivers these should be integrated into the END_DEVICE
 * structure.
 */

M_CL_CONFIG endMclConfig = 	/* network mbuf configuration table */
    {
    /* 
    no. mBlks		no. clBlks		memArea		memSize
    -----------		----------		-------		-------
    */
    0, 				0, 				NULL, 		0 
    };

CL_DESC endClDescTbl [] = 	/* network cluster pool configuration table */
    {
    /* 
    clusterSize		num		memArea		memSize
    -----------		----	-------		-------
    */
    {SNDS_CL_SIZE,	0,		NULL,		0}
    };

int endClDescTblNumEnt = (NELEMENTS(endClDescTbl));

/* new additions */

RECEIVE_FRAME_DESC 		*gpReceiveFrameDescStart;
TRANSMIT_FRAME_DESC 	*gpTransmitFrameDescStart;
UINT32 					 gStatusLengthPrevious;			/* For bug fix */
BOOL	gBugFixDone = FALSE;

/* Definitions for the flags field */

#define END_PROMISCUOUS_FLAG	0x1
#define END_RCV_HANDLING_FLAG	0x2
#define END_MBLK_NUM			400
#define END_CL_NUM				400
#define	SNDS_DATA_OFFSET 		2
#define	SNDS_MAX_MULTI	20

/* DEBUG MACROS */

#undef DEBUG

#ifdef DEBUG
#include "nvLogLib.h"			/* Needed to debug polled mode.  */
int endDebug = 1;
#define ENDLOGMSG(x) \
	if (endDebug) \
	    { \
	    logMsg x; \
	    }
#else
#define ENDLOGMSG(x)
#endif /* ENDDEBUG */

/* LOCALS */

#ifdef INCLUDE_SNDS_END

/* forward static functions */

LOCAL void		sndsEndReset			(END_DEVICE *pDrvCtrl);    /* added by knp/nts 14/9/99 */
LOCAL STATUS	sndsEndStart			(END_DEVICE *pDrvCtrl);    /* added by knp/nts 14/9/99 */
LOCAL void		sndsEndBdmaRxInt		(END_DEVICE *pDrvCtrl);    /* added by knp/nts 15/9/99 */
LOCAL void		sndsEndBdmaTxInt		(END_DEVICE *pDrvCtrl);
LOCAL void		sndsEndMacRxInt			(END_DEVICE *pDrvCtrl);
LOCAL void		sndsEndMacTxInt			(END_DEVICE *pDrvCtrl);
LOCAL void		sndsEndHandleRcvInt 	(END_DEVICE *pDrvCtrl, UINT32 stat);
LOCAL STATUS	sndsEndRecv				(END_DEVICE *pDrvCtrl, char* pData, UINT32 length);
LOCAL void		sndsEndConfig			(END_DEVICE *pDrvCtrl);
LOCAL UINT32	sndsEndPhyRead 			(UINT32 phyRegAddr, UINT32 phyAddr);
LOCAL void 		sndsEndPhyWrite 		(UINT32 phyRegAddr, UINT32 phyAddr, UINT32 phyData);
LOCAL void 		sndsEndMacInitialize	(END_DEVICE *pDevice);
LOCAL STATUS	sndsEndFdInitialize		(END_DEVICE *pDrvCrtl);
LOCAL void 		sndsEndFdFree			(END_DEVICE *pDrvCtrl);
LOCAL void 		sndsEndBugFix 			(UINT16 *);
LOCAL void sndsEndAddrFilterSet			(END_DEVICE *pDrvCtrl);

/* END Specific interfaces. */

/* This is the only externally visible interface. */

END_OBJ* 	sndsEndLoad (char* initString);

LOCAL STATUS	sndsEndStart		(END_DEVICE* pDrvCtrl);
LOCAL STATUS	sndsEndStop			(END_DEVICE* pDrvCtrl);
LOCAL STATUS	sndsEndUnload		();
LOCAL int		sndsEndIoctl		(END_DEVICE* pDrvCtrl, int cmd, caddr_t data);
LOCAL STATUS	sndsEndSend			(END_DEVICE* pDrvCtrl, M_BLK_ID pBuf);
			  
LOCAL STATUS	sndsEndMCastAdd 	(END_DEVICE* pDrvCtrl, char* pAddress);
LOCAL STATUS	sndsEndMCastDel 	(END_DEVICE* pDrvCtrl, char* pAddress);
LOCAL STATUS	sndsEndMCastGet 	(END_DEVICE* pDrvCtrl, MULTI_TABLE* pTable);
LOCAL STATUS	sndsEndPollSend 	(END_DEVICE* pDrvCtrl, M_BLK_ID pBuf);
LOCAL STATUS	sndsEndPollRcv 		(END_DEVICE* pDrvCtrl, M_BLK_ID pBuf);
LOCAL STATUS	sndsEndPollStart 	(END_DEVICE* pDrvCtrl);
LOCAL STATUS	sndsEndPollStop 	(END_DEVICE* pDrvCtrl);

LOCAL STATUS	sndsEndParse		();
LOCAL STATUS	sndsEndMemInit		();

/*
 * Declare our function table.  This is static across all driver
 * instances.
 */

LOCAL NET_FUNCS endFuncTable =
    {
    (STATUS (*) (END_OBJ*))sndsEndStart,				/* Function to start the device. */
    (STATUS (*) (END_OBJ*))sndsEndStop,				/* Function to stop the device. */
    (STATUS (*) (END_OBJ*))sndsEndUnload,				/* Unloading function for the driver. */
    (int (*) (END_OBJ*, int, caddr_t))sndsEndIoctl,				/* Ioctl function for the driver. */
	(STATUS (*) (END_OBJ* , M_BLK_ID))sndsEndSend,				/* Send function for the driver. */
    (STATUS (*) (END_OBJ*, char*))sndsEndMCastAdd,			/* Multicast address add function for the driver. */
    (STATUS (*) (END_OBJ*, char*))sndsEndMCastDel,			/* Multicast address delete function for the driver. */
    (STATUS (*) (END_OBJ*, MULTI_TABLE*))sndsEndMCastGet,			/* Multicast table retrieve function for the driver. */
    (STATUS (*) (END_OBJ*, M_BLK_ID))sndsEndPollSend,			/* Polling send function for the driver. */
    (STATUS (*) (END_OBJ*, M_BLK_ID))sndsEndPollRcv,				/* Polling receive function for the driver. */
    endEtherAddressForm,        /* Put address info into a packet.  */