?? fil.h
字號:
/*****************************************************************************/
/* */
/* COMPONENT : Rainbow */
/* MODULE : FIL */
/* NAME : Flash Interface Layer header file */
/* FILE : FIL.h */
/* PURPOSE : This file contains the definition and protypes of exported */
/* functions for FIL of Whimory. */
/* */
/*---------------------------------------------------------------------------*/
/* */
/* COPYRIGHT 2003-2005 SAMSUNG ELECTRONICS CO., LTD. */
/* ALL RIGHTS RESERVED */
/* */
/* Permission is hereby granted to licensees of Samsung Electronics */
/* Co., Ltd. products to use or abstract this computer program for the */
/* sole purpose of implementing a product based on Samsung */
/* Electronics Co., Ltd. products. No other rights to reproduce, use, */
/* or disseminate this computer program, whether in part or in whole, */
/* are granted. */
/* */
/* Samsung Electronics Co., Ltd. makes no representation or warranties */
/* with respect to the performance of this computer program, and */
/* specifically disclaims any responsibility for any damages, */
/* special or consequential, connected with the use of this program. */
/* */
/*---------------------------------------------------------------------------*/
/* */
/* REVISION HISTORY */
/* */
/* 19-JUL-2005 [Jaesung Jung] : first writing */
/* */
/*****************************************************************************/
#ifndef _FIL_H_
#define _FIL_H_
/*****************************************************************************/
/* Return value of FIL_XXX() & physical interface function pointer */
/*****************************************************************************/
#define FIL_SUCCESS WMR_RETURN_VALUE(0, 0x0000, 0x0000)
#define FIL_SUCCESS_CLEAN WMR_RETURN_VALUE(0, 0x0000, 0x0001)
#define FIL_CRITICAL_ERROR WMR_RETURN_VALUE(1, 0x0001, 0x0000)
#define FIL_U_ECC_ERROR WMR_RETURN_VALUE(1, 0x0002, 0x0000)
#define FIL_SYNC_FAIL WMR_RETURN_VALUE(1, 0x0003, 0x0000)
/*****************************************************************************/
/* FIL Function Table Data Structures */
/*****************************************************************************/
typedef struct {
UINT32 nType; /* 0 : OneNAND, 1 : read ID from NAND directly */
/* 2 : read ID from register of NAND controller */
UINT32 nAddrOfCmdReg; /* Address of command register */
UINT32 nAddrOfAdrReg; /* Address of address register */
UINT32 nAddrOfReadIDReg; /* Address of register for reading ID */
UINT32 nAddrOfStatusReg; /* Address of status register */
UINT32 nCmdOfReadID; /* Command of reading Device ID */
UINT32 nCmdOfReadPage; /* Command of read page */
UINT32 nCmdOfReadStatus; /* Command of read status */
UINT32 nMaskOfRnB; /* Mask value for Ready or Busy status */
} FILPlatformInfo;
typedef struct {
INT32 (*Init) (VOID);
VOID (*Reset) (UINT32 nBank);
INT32 (*Read) (UINT32 nBank, UINT32 nPpn, UINT32 nSctBitmap, UINT32 nPlaneBitmap,
UINT8 *pDBuf, UINT8 *pSBuf, BOOL32 bECCIn, BOOL32 bCleanCheck);
VOID (*Write) (UINT32 nBank, UINT32 nPpn, UINT32 nSctBitmap, UINT32 nPlaneBitmap,
UINT8 *pDBuf, UINT8 *pSBuf);
VOID (*Erase) (UINT32 nBank, UINT32 nPbn, UINT32 nPlaneBitmap);
INT32 (*Sync) (UINT32 nBank, UINT32 *nPlaneBitmap);
#if (WMR_SUPPORT_META_WEAR_LEVEL && WMR_SIMULATION)
VOID (*Swap) (UINT32 nBank, UINT32 nMetaPbn, UINT32 nDataPbn, UINT32 nMetaBlkBitmap, UINT32 nDataBlkBitmap);
#endif
VOID (*Steploader_Write) (UINT32 nBank, UINT32 nPpn, UINT32 nSctBitmap, UINT32 nPlaneBitmap,
UINT8 *pDBuf, UINT8 *pSBuf);
VOID (*GetPlatformInfo) (FILPlatformInfo* pstFILPlatformInfo);
} LowFuncTbl;
/*****************************************************************************/
/* Exported Function Prototype of FIL */
/*****************************************************************************/
#ifdef __cplusplus
extern "C" {
#endif /* __cplusplus */
INT32 FIL_Init (VOID);
LowFuncTbl *FIL_GetFuncTbl (VOID);
#ifdef __cplusplus
}
#endif /* __cplusplus */
#endif /* _FIL_H_ */
?? 快捷鍵說明
復制代碼
Ctrl + C
搜索代碼
Ctrl + F
全屏模式
F11
切換主題
Ctrl + Shift + D
顯示快捷鍵
?
增大字號
Ctrl + =
減小字號
Ctrl + -