#include <msp430x14x.h>
#include "key.h"

void Init_Port(void)
{
    //將P1口所有的管腳在初始化的時候設置為輸入方式
    P1DIR = 0;
 
    //將P1口所有的管腳設置為一般I/O口
    P1SEL = 0;
    
    // 將P1.4 P1.5 P1.6 P1.7設置為輸出方向
    P1DIR |= BIT4;
    P1DIR |= BIT5;
	P1DIR |= BIT6;
    P1DIR |= BIT7;

	//先輸出低電平
	P1OUT = 0x00;
    return;
}
int KeyScan(void)
{
	int nP10,nP11,nP12,nP13;
	int nRes = 0;
	for(;;)
	{
		//讀取各個管腳的狀態
		nP10 = P1IN & BIT0;
		nP11 = (P1IN & BIT1) >> 1;
		nP12 = (P1IN & BIT2) >> 2;
		nP13 = (P1IN & BIT3) >> 3;

		//是否有鍵被按下
		if(nP10 == 0 || nP11 == 0 || nP12 == 0 || nP13 == 0)
		{
			//有鍵被按下
			break;
		}
		
	}
    Delay(); //延時一點時間，消除抖動
	//讀取各個管腳的狀態
	nP10 = P1IN & BIT0;
	nP11 = (P1IN & BIT1) >> 1;
	nP12 = (P1IN & BIT2) >> 2;
	nP13 = (P1IN & BIT3) >> 3;

	//是否有鍵被按下
	if(nP10 == 0 || nP11 == 0 || nP12 == 0 || nP13 == 0)
	{
		//有鍵被按下，進行鍵盤輸入分析
		nRes = KeyProcess();
	}
	else return -1;//沒有輸入，為干擾

	return nRes;
}
void Delay(void)
{
	int i;
	for(i = 100;i > 0;i--) ;//延時一點時間
}
int KeyProcess(void)
{
	int nRes = 0;
        int nP10;
        int nP11;
        int nP12;
        int nP13;
	//P1.4輸出低電平
	P1OUT &= ~(BIT4);
	nP10 = P1IN & BIT0;
	if (nP10 == 0) nRes = 13;
	nP11 = (P1IN & BIT1) >> 1;
	if (nP11 == 0) nRes = 14;
	nP12 = (P1IN & BIT2) >> 2;
	if (nP12 == 0) nRes = 15;
	nP13 = (P1IN & BIT3) >> 3;
	if (nP13 == 0) nRes = 16;
	//P1.5輸出低電平
	P1OUT &= ~(BIT4);
	nP10 = P1IN & BIT0;
	if (nP10 == 0) nRes = 9;
	nP11 = (P1IN & BIT1) >> 1;
	if (nP11 == 0) nRes = 10;
	nP12 = (P1IN & BIT2) >> 2;
	if (nP12 == 0) nRes = 11;
	nP13 = (P1IN & BIT3) >> 3;
	if (nP13 == 0) nRes = 12;
	//P1.6輸出低電平
	P1OUT &= ~(BIT4);
	nP10 = P1IN & BIT0;
	if (nP10 == 0) nRes = 5;
	nP11 = (P1IN & BIT1) >> 1;
	if (nP11 == 0) nRes = 6;
	nP12 = (P1IN & BIT2) >> 2;
	if (nP12 == 0) nRes = 7;
	nP13 = (P1IN & BIT3) >> 3;
	if (nP13 == 0) nRes = 8;
	//P1.7輸出低電平
	P1OUT &= ~(BIT4);
	nP10 = P1IN & BIT0;
	if (nP10 == 0) nRes = 1;
	nP11 = (P1IN & BIT1) >> 1;
	if (nP11 == 0) nRes = 2;
	nP12 = (P1IN & BIT2) >> 2;
	if (nP12 == 0) nRes = 3;
	nP13 = (P1IN & BIT3) >> 3;
	if (nP13 == 0) nRes = 4;

	P1OUT = 0x00;//恢復以前值。

	//讀取各個管腳的狀態
	nP10 = P1IN & BIT0;
	nP11 = (P1IN & BIT1) >> 1;
	nP12 = (P1IN & BIT2) >> 2;
	nP13 = (P1IN & BIT3) >> 3;
	for(;;)
	{
		if(nP10 == 1 && nP11 == 1 && nP12 == 1 && nP13 == 1)
		{
			//等待松開按鍵
			break;
		}
	}
	return nRes;
}
void Init_CLK(void)
{
    unsigned int i;
    BCSCTL1 = 0X00;			//將寄存器的內容清零
					//XT2震蕩器開啟
					//LFTX1工作在低頻模式
					//ACLK的分頻因子為1
					
    do 
    {
	IFG1 &= ~OFIFG;                       // 清除OSCFault標志
	for (i = 0x20; i > 0; i--);                
    }
    while ((IFG1 & OFIFG) == OFIFG);      // 如果OSCFault =1   
					
    BCSCTL2 = 0X00;			//將寄存器的內容清零
    BCSCTL2 += SELM1;		//MCLK的時鐘源為TX2CLK，分頻因子為1
    BCSCTL2 += SELS;		//SMCLK的時鐘源為TX2CLK，分頻因子為1
}