/*                      - lnkm128.xcl - * *   XLINK command file for the ICCAVR C-compiler using the --cpu=m128, -ms *   options. Segments are defined for an ATmega128 whithout external *   memory. It is also possible to "add" external SRAM, EPROM and EEPROM. * *   Usage: xlink your_file(s) -f lnkm128 * *   File version:   $Name: demo-bldc-sensor-at90pwm3-4_2_0 $ *//* * Modify the lines below to alter the size of the RSTACK, CSTACK and HEAP * segments. These need to be fine tuned to suit your specific application. * The '_..X_' prefix is used by C-SPY as an indication that the label should * not be displayed in the dissassembly window. */-D_..X_CSTACK_SIZE=200  /* 512 bytes for auto variables and saved registers. */-D_..X_RSTACK_SIZE=40   /* 64 bytes for return addresses, equivalent to 32 */                        /* levels of calls, including interrupts. */-D_..X_HEAP_SIZE=100    /* 256 bytes of heap. *//* * Modify these lines if you have an external SRAM connected to the system. * * Note: Remember to turn on the external data and address busses in *       __low_level_init if external memory is used. */-D_..X_EXT_SRAM_BASE=0-D_..X_EXT_SRAM_SIZE=0/* * Modify these lines if you have an external EPROM connected to the system. * * Note: Remember to turn on the external data and address busses in *       __low_level_init if external memory is used. */-D_..X_EXT_EPROM_BASE=0-D_..X_EXT_EPROM_SIZE=0/* * Modify these lines if you have an external EEPROM connected to the system. * * Note: Remember to turn on the external data and address busses in *       __low_level_init if external memory is used. */-D_..X_EXT_EEPROM_BASE=0-D_..X_EXT_EEPROM_SIZE=0/* Define CPU */-ca90/* * The following segments are located in the internal memory of * the ATmega128. Do not change these lines. *//*====================================================*//* Code (flash) segments */-D_..X_INTVEC_SIZE=8C   /* 4 bytes * 35 vectors */-D_..X_FLASH_TEND=FF    /* End of tiny flash memory */-D_..X_FLASH_NEND=FFFF  /* End of near flash memory */-D_..X_FLASH_END=1FFFF  /* End of flash memory *//* Internal data memory *//* Change the two lines below to 60(BASE) and FF(TEND) if you are running in "mega103 mode" */-D_..X_SRAM_BASE=100    /* Start of ram memory */-D_..X_SRAM_TEND=100    /* End of tiny ram memory */-D_..X_SRAM_END=10FF    /* End of ram memory *//* Internal EEPROM */-D_..X_EEPROM_END=FFF   /* End of eeprom memory *//*====================================================*//* Code memory */-Z(CODE)INTVEC=0-(_..X_INTVEC_SIZE-1) /* Fill unused interrupt vector's with RETI */-H1895-h(CODE)0-_..X_INTVEC_SIZE-Z(CODE)TINY_F=_..X_INTVEC_SIZE-_..X_FLASH_TEND-Z(CODE)NEAR_F,SWITCH,INITTAB,DIFUNCT=_..X_INTVEC_SIZE-_..X_FLASH_NEND-Z(CODE)CODE=_..X_INTVEC_SIZE-_..X_FLASH_END-Z(FARCODE)FAR_F=_..X_INTVEC_SIZE-_..X_FLASH_END-Z(CODE)HUGE_F=_..X_INTVEC_SIZE-_..X_FLASH_END-Z(CODE)TINY_ID,NEAR_ID,CHECKSUM=_..X_INTVEC_SIZE-_..X_FLASH_END/* Internal data memory */-Z(DATA)TINY_I,TINY_Z,TINY_N=_..X_SRAM_BASE-_..X_SRAM_TEND-Z(DATA)NEAR_I,NEAR_Z=_..X_SRAM_BASE-_..X_SRAM_END,_..X_EXT_SRAM_BASE-(_..X_EXT_SRAM_BASE+_..X_EXT_SRAM_SIZE)/* * If external SRAM is available it is possible to place the stacks there. * However, the external memory is slower than the internal so moving the * stacks to the external memory will degrade the system performance. */-Z(DATA)RSTACK+_..X_RSTACK_SIZE=_..X_SRAM_BASE-_..X_SRAM_END /* ,_..X_EXT_SRAM_BASE-(_..X_EXT_SRAM_BASE+_..X_EXT_SRAM_SIZE) */-Z(DATA)CSTACK+_..X_CSTACK_SIZE=_..X_SRAM_BASE-_..X_SRAM_END /* ,_..X_EXT_SRAM_BASE-(_..X_EXT_SRAM_BASE+_..X_EXT_SRAM_SIZE) *//* * If external SRAM is available it might be a good idea to move the * heap segment there, i.e. remove the _..X_SRAM_BASE-_..X_SRAM_END range. */-Z(DATA)HEAP+_..X_HEAP_SIZE=_..X_SRAM_BASE-_..X_SRAM_END,_..X_EXT_SRAM_BASE-(_..X_EXT_SRAM_BASE+_..X_EXT_SRAM_SIZE)/* Internal eeprom memory */-Z(XDATA)EEPROM_I,EEPROM_N=0-_..X_EEPROM_END/* * The following segment definitions are only used if external memory is * connected to the AVR controller. *//* External EPROM */-Z(CONST)NEAR_C=_..X_EXT_EPROM_BASE-(_..X_EXT_EPROM_BASE+_..X_EXT_EPROM_SIZE)/* External EEPROM */-Z(DATA)NEAR_N=_..X_EXT_EEPROM_BASE-(_..X_EXT_EEPROM_BASE+_..X_EXT_EEPROM_SIZE)/* Select reduced "printf" support to reduce library size.   See configuration section in manual concerning printf/sprintf. */-e_Printf_1=_Printf/* Disable floating-point support in "scanf" to reduce library size.   See configuration section in manual concerning scanf/sscanf */-e_Scanf_1=_Scanf/* Suppress one warning which is not relevant for this processor */-w29/* Code will now reside in file aout.a90 or aout.d90, unless -o is specified *//* .d90 is the default if debug system is linked (option -r) *//* .a90 is the default without debugging. Default format is -Fmotorola */