/* * BK Id: SCCS/s.qspan_pci.c 1.6 05/18/01 15:17:06 cort *//* * LinuxPPC arch/ppc/kernel/qspan_pci.c   Dan Malek (dmalek@jlc.net) * * QSpan Motorola bus to PCI bridge.  The config address register * is located 0x500 from the base of the bridge control/status registers. * The data register is located at 0x504. * This is a two step operation.  First, the address register is written, * then the data register is read/written as required. * I don't know what to do about interrupts (yet). */#include <linux/types.h>#include <linux/kernel.h>#include <linux/pci.h>#include <asm/mpc8xx.h>/* * When reading the configuration space, if something does not respond * the bus times out and we get a machine check interrupt.  So, the * good ol' exception tables come to mind to trap it and return some * value. * * On an error we just return a -1, since that is what the caller wants * returned if nothing is present.  I copied this from __get_user_asm, * with the only difference of returning -1 instead of EFAULT. * There is an associated hack in the machine check trap code. * * The QSPAN is also a big endian device, that is it makes the PCI * look big endian to us.  This presents a problem for the Linux PCI * functions, which assume little endian.  For example, we see the * first 32-bit word like this: *	------------------------ *	| Device ID | Vendor ID | *	------------------------ * If we read/write as a double word, that's OK.  But in our world, * when read as a word, device ID is at location 0, not location 2 as * the little endian PCI would believe.  We have to switch bits in * the PCI addresses given to us to get the data to/from the correct * byte lanes. * * The QSPAN only supports 4 bits of "slot" in the dev_fn instead of 5. * It always forces the MS bit to zero.  Therefore, dev_fn values * greater than 128 are returned as "no device found" errors. * * The QSPAN can only perform long word (32-bit) configuration cycles. * The "offset" must have the two LS bits set to zero.  Read operations * require we read the entire word and then sort out what should be * returned.  Write operations other than long word require that we * read the long word, update the proper word or byte, then write the * entire long word back. * * PCI Bridge hack.  We assume (correctly) that bus 0 is the primary * PCI bus from the QSPAN.  If we are called with a bus number other * than zero, we create a Type 1 configuration access that a downstream * PCI bridge will interpret. */#define __get_pci_config(x, addr, op)		\	__asm__ __volatile__(				\		"1:	"op" %0,0(%1)\n"		\		"	eieio\n"			\		"2:\n"					\		".section .fixup,\"ax\"\n"		\		"3:	li %0,-1\n"			\		"	b 2b\n"				\		".section __ex_table,\"a\"\n"		\		"	.align 2\n"			\		"	.long 1b,3b\n"			\		".text"					\		: "=r"(x) : "r"(addr))#define QS_CONFIG_ADDR	((volatile uint *)(PCI_CSR_ADDR + 0x500))#define QS_CONFIG_DATA	((volatile uint *)(PCI_CSR_ADDR + 0x504))#define mk_config_addr(bus, dev, offset) \	(((bus)<<16) | ((dev)<<8) | (offset & 0xfc))#define mk_config_type1(bus, dev, offset) \	mk_config_addr(bus, dev, offset) | 1;/* Initialize the QSpan device registers after power up.*/qspan_init(){	uint	*qptr;	qptr = (uint *)PCI_CSR_ADDR;	/* PCI Configuration/status.  Upper bits written to clear	 * pending interrupt or status.  Lower bits enable QSPAN as	 * PCI master, enable memory and I/O cycles, and enable PCI	 * parity error checking.	 * IMPORTANT:  The last two bits of this word enable PCI	 * master cycles into the QBus.  The QSpan is broken and can't	 * meet the timing specs of the PQ bus for this to work.  Therefore,	 * if you don't have external bus arbitration, you can't use	 * this function.	 */#ifdef EXTERNAL_PQ_ARB	qptr[1] = 0xf9000147;#else	qptr[1] = 0xf9000144;#endif	/* PCI Misc configuration.  Set PCI latency timer resolution	 * of 8 cycles, set cache size to 4 x 32.	 */	qptr[3] = 0;	/* Set up PCI Target address mapping.  Enable, Posted writes,	 * 2Gbyte space (processor memory controller determines actual size).	 */	qptr[64] = 0x8f000080;	/* Map processor 0x80000000 to PCI 0x00000000.	 * Processor address bit 1 determines I/O type access (0x80000000)	 * or memory type access (0xc0000000).	 */	qptr[65] = 0x80000000;	/* Enable error logging and clear any pending error status.	*/	qptr[80] = 0x90000000;	qptr[512] = 0x000c0003;	/* Set up Qbus slave image.	*/	qptr[960] = 0x01000000;	qptr[961] = 0x000000d1;	qptr[964] = 0x00000000;	qptr[965] = 0x000000d1;}/* Functions to support PCI bios-like features to read/write configuration * space.  If the function fails for any reason, a -1 (0xffffffff) value * must be returned. */#define DEVICE_NOT_FOUND	(-1)#define SUCCESSFUL		0int qs_pci_read_config_byte(unsigned char bus, unsigned char dev_fn,				  unsigned char offset, unsigned char *val){	uint	temp;	u_char	*cp;	if ((bus > 7) || (dev_fn > 127)) {		*val = 0xff;		return DEVICE_NOT_FOUND;	}	if (bus == 0)		*QS_CONFIG_ADDR = mk_config_addr(bus, dev_fn, offset);	else		*QS_CONFIG_ADDR = mk_config_type1(bus, dev_fn, offset);	__get_pci_config(temp, QS_CONFIG_DATA, "lwz");	offset ^= 0x03;	cp = ((u_char *)&temp) + (offset & 0x03);	*val = *cp;	return SUCCESSFUL;}int qs_pci_read_config_word(unsigned char bus, unsigned char dev_fn,				  unsigned char offset, unsigned short *val){	uint	temp;	ushort	*sp;	if ((bus > 7) || (dev_fn > 127)) {		*val = 0xffff;		return DEVICE_NOT_FOUND;	}	if (bus == 0)		*QS_CONFIG_ADDR = mk_config_addr(bus, dev_fn, offset);	else		*QS_CONFIG_ADDR = mk_config_type1(bus, dev_fn, offset);	__get_pci_config(temp, QS_CONFIG_DATA, "lwz");	offset ^= 0x02;	sp = ((ushort *)&temp) + ((offset >> 1) & 1);	*val = *sp;	return SUCCESSFUL;}int qs_pci_read_config_dword(unsigned char bus, unsigned char dev_fn,				   unsigned char offset, unsigned int *val){	if ((bus > 7) || (dev_fn > 127)) {		*val = 0xffffffff;		return DEVICE_NOT_FOUND;	}	if (bus == 0)		*QS_CONFIG_ADDR = mk_config_addr(bus, dev_fn, offset);	else		*QS_CONFIG_ADDR = mk_config_type1(bus, dev_fn, offset);	__get_pci_config(*val, QS_CONFIG_DATA, "lwz");	return SUCCESSFUL;}int qs_pci_write_config_byte(unsigned char bus, unsigned char dev_fn,				   unsigned char offset, unsigned char val){	uint	temp;	u_char	*cp;	if ((bus > 7) || (dev_fn > 127))		return DEVICE_NOT_FOUND;	qs_pci_read_config_dword(bus, dev_fn, offset, &temp);	offset ^= 0x03;	cp = ((u_char *)&temp) + (offset & 0x03);	*cp = val;	if (bus == 0)		*QS_CONFIG_ADDR = mk_config_addr(bus, dev_fn, offset);	else		*QS_CONFIG_ADDR = mk_config_type1(bus, dev_fn, offset);	*QS_CONFIG_DATA = temp;	return SUCCESSFUL;}int qs_pci_write_config_word(unsigned char bus, unsigned char dev_fn,				   unsigned char offset, unsigned short val){	uint	temp;	ushort	*sp;	if ((bus > 7) || (dev_fn > 127))		return DEVICE_NOT_FOUND;	qs_pci_read_config_dword(bus, dev_fn, offset, &temp);	offset ^= 0x02;	sp = ((ushort *)&temp) + ((offset >> 1) & 1);	*sp = val;	if (bus == 0)		*QS_CONFIG_ADDR = mk_config_addr(bus, dev_fn, offset);	else		*QS_CONFIG_ADDR = mk_config_type1(bus, dev_fn, offset);	*QS_CONFIG_DATA = temp;	return SUCCESSFUL;}int qs_pci_write_config_dword(unsigned char bus, unsigned char dev_fn,				    unsigned char offset, unsigned int val){	if ((bus > 7) || (dev_fn > 127))		return DEVICE_NOT_FOUND;	if (bus == 0)		*QS_CONFIG_ADDR = mk_config_addr(bus, dev_fn, offset);	else		*QS_CONFIG_ADDR = mk_config_type1(bus, dev_fn, offset);	*(unsigned int *)QS_CONFIG_DATA = val;	return SUCCESSFUL;}