/* * Carsten Langgaard, carstenl@mips.com * Copyright (C) 1999, 2000 MIPS Technologies, Inc.  All rights reserved. * * ######################################################################## * *  This program is free software; you can distribute it and/or modify it *  under the terms of the GNU General Public License (Version 2) as *  published by the Free Software Foundation. * *  This program is distributed in the hope it will be useful, but WITHOUT *  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or *  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License *  for more details. * *  You should have received a copy of the GNU General Public License along *  with this program; if not, write to the Free Software Foundation, Inc., *  59 Temple Place - Suite 330, Boston MA 02111-1307, USA. * * ######################################################################## * * Interrupt exception dispatch code. * */#include <linux/config.h>#include <asm/asm.h>#include <asm/mipsregs.h>#include <asm/regdef.h>#include <asm/stackframe.h>/* A lot of complication here is taken away because: * * 1) We handle one interrupt and return, sitting in a loop and moving across *    all the pending IRQ bits in the cause register is _NOT_ the answer, the *    common case is one pending IRQ so optimize in that direction. * * 2) We need not check against bits in the status register IRQ mask, that *    would make this routine slow as hell. * * 3) Linux only thinks in terms of all IRQs on or all IRQs off, nothing in *    between like BSD spl() brain-damage. * * Furthermore, the IRQs on the MIPS board look basically (barring software * IRQs which we don't use at all and all external interrupt sources are * combined together on hardware interrupt 0 (MIPS IRQ 2)) like: * *	MIPS IRQ	Source *      --------        ------ *             0	Software (ignored) *             1        Software (ignored) *             2        Combined hardware interrupt (hw0) *             3        Hardware (ignored) *             4        Hardware (ignored) *             5        Hardware (ignored) *             6        Hardware (ignored) *             7        R4k timer (what we use) * * We handle the IRQ according to _our_ priority which is: * * Highest ----     R4k Timer * Lowest  ----     Combined hardware interrupt * * then we just return, if multiple IRQs are pending then we will just take * another exception, big deal. */	.text	.set	noreorder	.set	noat	.align	5	NESTED(mipsIRQ, PT_SIZE, sp)	SAVE_ALL	CLI	.set	at	mfc0	s0, CP0_CAUSE		# get irq mask	/* First we check for r4k counter/timer IRQ. */	andi	a0, s0, CAUSEF_IP7	beq	a0, zero, 1f	 andi	a0, s0, CAUSEF_IP2	# delay slot, check hw0 interrupt	/* Wheee, a timer interrupt. */	move	a0, sp	jal	mips_timer_interrupt	 nop	j	ret_from_irq	 nop1:	beq	a0, zero, 1f	 nop	/* Wheee, combined hardware level zero interrupt. */#if defined(CONFIG_MIPS_ATLAS)	jal	atlas_hw0_irqdispatch#elif defined(CONFIG_MIPS_MALTA)	jal	malta_hw0_irqdispatch#else#error "MIPS board not supported\n"	#endif	 move	a0, sp			# delay slot	j	ret_from_irq	 nop				# delay slot1:	/*	 * Here by mistake?  This is possible, what can happen is that by the	 * time we take the exception the IRQ pin goes low, so just leave if	 * this is the case.	 */	move	a1,s0	PRINT("Got interrupt: c0_cause = %08x\n")	mfc0	a1, CP0_EPC	PRINT("c0_epc = %08x\n")	j	ret_from_irq	 nop	END(mipsIRQ)