/* * linux/arch/sh/kernel/pci-7751se.c * * Author:  Ian DaSilva (idasilva@mvista.com) * * Highly leveraged from pci-bigsur.c, written by Dustin McIntire. * * May be copied or modified under the terms of the GNU General Public * License.  See linux/COPYING for more information. * * PCI initialization for the Hitachi SH7751 Solution Engine board (MS7751SE01) */#include <linux/config.h>#include <linux/kernel.h>#include <linux/types.h>#include <linux/init.h>#include <linux/delay.h>#include <linux/pci.h>#include <asm/io.h>#include <asm/pci-sh7751.h>#define PCIMCR_MRSET_OFF	0xBFFFFFFF#define PCIMCR_RFSH_OFF		0xFFFFFFFB/* * Only long word accesses of the PCIC's internal local registers and the * configuration registers from the CPU is supported. */#define PCIC_WRITE(x,v) writel((v), PCI_REG(x))#define PCIC_READ(x) readl(PCI_REG(x))/* * Description:  This function sets up and initializes the pcic, sets * up the BARS, maps the DRAM into the address space etc, etc. */int __init pcibios_init_platform(void){   unsigned long bcr1, wcr1, wcr2, wcr3, mcr;   unsigned short bcr2;   /*    * Initialize the slave bus controller on the pcic.  The values used    * here should not be hardcoded, but they should be taken from the bsc    * on the processor, to make this function as generic as possible.    * (i.e. Another sbc may usr different SDRAM timing settings -- in order    * for the pcic to work, its settings need to be exactly the same.)    */   bcr1 = (*(volatile unsigned long*)(SH7751_BCR1));   bcr2 = (*(volatile unsigned short*)(SH7751_BCR2));   wcr1 = (*(volatile unsigned long*)(SH7751_WCR1));   wcr2 = (*(volatile unsigned long*)(SH7751_WCR2));   wcr3 = (*(volatile unsigned long*)(SH7751_WCR3));   mcr = (*(volatile unsigned long*)(SH7751_MCR));   bcr1 = bcr1 | 0x00080000;  /* Enable Bit 19, BREQEN */   (*(volatile unsigned long*)(SH7751_BCR1)) = bcr1;      bcr1 = bcr1 | 0x40080000;  /* Enable Bit 19 BREQEN, set PCIC to slave */   PCIC_WRITE(SH7751_PCIBCR1, bcr1);	 /* PCIC BCR1 */   PCIC_WRITE(SH7751_PCIBCR2, bcr2);     /* PCIC BCR2 */   PCIC_WRITE(SH7751_PCIWCR1, wcr1);     /* PCIC WCR1 */   PCIC_WRITE(SH7751_PCIWCR2, wcr2);     /* PCIC WCR2 */   PCIC_WRITE(SH7751_PCIWCR3, wcr3);     /* PCIC WCR3 */   mcr = (mcr & PCIMCR_MRSET_OFF) & PCIMCR_RFSH_OFF;   PCIC_WRITE(SH7751_PCIMCR, mcr);      /* PCIC MCR */   /* Enable all interrupts, so we know what to fix */   PCIC_WRITE(SH7751_PCIINTM, 0x0000c3ff);   PCIC_WRITE(SH7751_PCIAINTM, 0x0000380f);   /* Set up standard PCI config registers */   PCIC_WRITE(SH7751_PCICONF1, 	0xF39000C7); /* Bus Master, Mem & I/O access */   PCIC_WRITE(SH7751_PCICONF2, 	0x00000000); /* PCI Class code & Revision ID */   PCIC_WRITE(SH7751_PCICONF4, 	0xab000001); /* PCI I/O address (local regs) */   PCIC_WRITE(SH7751_PCICONF5, 	0x0c000000); /* PCI MEM address (local RAM)  */   PCIC_WRITE(SH7751_PCICONF6, 	0xd0000000); /* PCI MEM address (unused)     */   PCIC_WRITE(SH7751_PCICONF11, 0x35051054); /* PCI Subsystem ID & Vendor ID */   PCIC_WRITE(SH7751_PCILSR0, 0x03f00000);   /* MEM (full 64M exposed)       */   PCIC_WRITE(SH7751_PCILSR1, 0x00000000);   /* MEM (unused)                 */   PCIC_WRITE(SH7751_PCILAR0, 0x0c000000);   /* MEM (direct map from PCI)    */   PCIC_WRITE(SH7751_PCILAR1, 0x00000000);   /* MEM (unused)                 */   /* Now turn it on... */   PCIC_WRITE(SH7751_PCICR, 0xa5000001);   /*    * Set PCIMBR and PCIIOBR here, assuming a single window    * (16M MEM, 256K IO) is enough.  If a larger space is    * needed, the readx/writex and inx/outx functions will    * have to do more (e.g. setting registers for each call).    */   /*    * Set the MBR so PCI address is one-to-one with window,    * meaning all calls go straight through... use ifdef to    * catch erroneous assumption.    */#if PCIBIOS_MIN_MEM != SH7751_PCI_MEMORY_BASE#error One-to-one assumption for PCI memory mapping is wrong!?!?!?#endif      PCIC_WRITE(SH7751_PCIMBR, PCIBIOS_MIN_MEM);   /* Set IOBR for window containing area specified in pci.h */   PCIC_WRITE(SH7751_PCIIOBR, (PCIBIOS_MIN_IO & SH7751_PCIIOBR_MASK));   /* All done, may as well say so... */   printk("SH7751 PCI: Finished initialization of the PCI controller\n");   return 1;}int __init pcibios_map_platform_irq(u8 slot, u8 pin){        switch (slot) {        case 0: return 13;        case 1: return 13; 	/* AMD Ethernet controller */        case 2: return -1;        case 3: return -1;        case 4: return -1;        default:                printk("PCI: Bad IRQ mapping request for slot %d\n", slot);                return -1;        }}