/* sgiserial.h: Definitions for the SGI Zilog85C30 serial driver. * * Copyright (C) 1996 David S. Miller (dm@engr.sgi.com) */#ifndef _SGI_SERIAL_H#define _SGI_SERIAL_H/* Just one channel */struct sgi_zschannel {#ifdef __MIPSEB__	volatile unsigned char unused0[3];	volatile unsigned char control;	volatile unsigned char unused1[3];	volatile unsigned char data;#else /* __MIPSEL__ */	volatile unsigned char control;	volatile unsigned char unused0[3];	volatile unsigned char data;	volatile unsigned char unused1[3];#endif};/* The address space layout for each zs chip.  Yes they are * backwards. */struct sgi_zslayout {	struct sgi_zschannel channelB;	struct sgi_zschannel channelA;};#define NUM_ZSREGS    16struct serial_struct {	int	type;	int	line;	int	port;	int	irq;	int	flags;	int	xmit_fifo_size;	int	custom_divisor;	int	baud_base;	unsigned short	close_delay;	char	reserved_char[2];	int	hub6;	unsigned short	closing_wait; /* time to wait before closing */	unsigned short	closing_wait2; /* no longer used... */	int	reserved[4];};/* * For the close wait times, 0 means wait forever for serial port to * flush its output.  65535 means don't wait at all. */#define ZILOG_CLOSING_WAIT_INF	0#define ZILOG_CLOSING_WAIT_NONE	65535/* * Definitions for ZILOG_struct (and serial_struct) flags field */#define ZILOG_HUP_NOTIFY 0x0001 /* Notify getty on hangups and closes				   on the callout port */#define ZILOG_FOURPORT  0x0002	/* Set OU1, OUT2 per AST Fourport settings */#define ZILOG_SAK	0x0004	/* Secure Attention Key (Orange book) */#define ZILOG_SPLIT_TERMIOS 0x0008 /* Separate termios for dialin/callout */#define ZILOG_SPD_MASK	0x0030#define ZILOG_SPD_HI	0x0010	/* Use 56000 instead of 38400 bps */#define ZILOG_SPD_VHI	0x0020  /* Use 115200 instead of 38400 bps */#define ZILOG_SPD_CUST	0x0030  /* Use user-specified divisor */#define ZILOG_SKIP_TEST	0x0040 /* Skip UART test during autoconfiguration */#define ZILOG_AUTO_IRQ  0x0080 /* Do automatic IRQ during autoconfiguration */#define ZILOG_SESSION_LOCKOUT 0x0100 /* Lock out cua opens based on session */#define ZILOG_PGRP_LOCKOUT    0x0200 /* Lock out cua opens based on pgrp */#define ZILOG_CALLOUT_NOHUP   0x0400 /* Don't do hangups for cua device */#define ZILOG_FLAGS	0x0FFF	/* Possible legal ZILOG flags */#define ZILOG_USR_MASK 0x0430	/* Legal flags that non-privileged				 * users can set or reset *//* Internal flags used only by kernel/chr_drv/serial.c */#define ZILOG_INITIALIZED	0x80000000 /* Serial port was initialized */#define ZILOG_CALLOUT_ACTIVE	0x40000000 /* Call out device is active */#define ZILOG_NORMAL_ACTIVE	0x20000000 /* Normal device is active */#define ZILOG_BOOT_AUTOCONF	0x10000000 /* Autoconfigure port on bootup */#define ZILOG_CLOSING		0x08000000 /* Serial port is closing */#define ZILOG_CTS_FLOW		0x04000000 /* Do CTS flow control */#define ZILOG_CHECK_CD		0x02000000 /* i.e., CLOCAL *//* Software state per channel */#ifdef __KERNEL__/* * This is our internal structure for each serial port's state. * * Many fields are paralleled by the structure used by the serial_struct * structure. * * For definitions of the flags field, see tty.h */struct sgi_serial {	struct sgi_serial *zs_next;       /* For IRQ servicing chain */	struct sgi_zschannel *zs_channel; /* Channel registers */	unsigned char read_reg_zero;	char soft_carrier;  /* Use soft carrier on this channel */	char cons_keyb;     /* Channel runs the keyboard */	char cons_mouse;    /* Channel runs the mouse */	char break_abort;   /* Is serial console in, so process brk/abrt */	char kgdb_channel;  /* Kgdb is running on this channel */	char is_cons;       /* Is this our console. */	/* We need to know the current clock divisor	 * to read the bps rate the chip has currently	 * loaded.	 */	unsigned char clk_divisor;  /* May be 1, 16, 32, or 64 */	int zs_baud;	/* Current write register values */	unsigned char curregs[NUM_ZSREGS];	/* Values we need to set next opportunity */	unsigned char pendregs[NUM_ZSREGS];	char change_needed;	int			magic;	int			baud_base;	int			port;	int			irq;	int			flags; 		/* defined in tty.h */	int			type; 		/* UART type */	struct tty_struct 	*tty;	int			read_status_mask;	int			ignore_status_mask;	int			timeout;	int			xmit_fifo_size;	int			custom_divisor;	int			x_char;	/* xon/xoff character */	int			close_delay;	unsigned short		closing_wait;	unsigned short		closing_wait2;	unsigned long		event;	unsigned long		last_active;	int			line;	int			count;	    /* # of fd on device */	int			blocked_open; /* # of blocked opens */	long			session; /* Session of opening process */	long			pgrp; /* pgrp of opening process */	unsigned char 		*xmit_buf;	int			xmit_head;	int			xmit_tail;	int			xmit_cnt;	struct tq_struct	tqueue;	struct tq_struct	tqueue_hangup;	struct termios		normal_termios;	struct termios		callout_termios;	wait_queue_head_t	open_wait;	wait_queue_head_t	close_wait;};#define SERIAL_MAGIC 0x5301/* * The size of the serial xmit buffer is 1 page, or 4096 bytes */#define SERIAL_XMIT_SIZE 4096/* * Events are used to schedule things to happen at timer-interrupt * time, instead of at rs interrupt time. */#define RS_EVENT_WRITE_WAKEUP	0#endif /* __KERNEL__ *//* Conversion routines to/from brg time constants from/to bits * per second. */#define BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2))#define BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2)/* The Zilog register set */#define	FLAG	0x7e/* Write Register 0 */#define	R0	0		/* Register selects */#define	R1	1#define	R2	2#define	R3	3#define	R4	4#define	R5	5#define	R6	6#define	R7	7#define	R8	8#define	R9	9#define	R10	10#define	R11	11#define	R12	12#define	R13	13#define	R14	14#define	R15	15#define	NULLCODE	0	/* Null Code */#define	POINT_HIGH	0x8	/* Select upper half of registers */#define	RES_EXT_INT	0x10	/* Reset Ext. Status Interrupts */#define	SEND_ABORT	0x18	/* HDLC Abort */#define	RES_RxINT_FC	0x20	/* Reset RxINT on First Character */#define	RES_Tx_P	0x28	/* Reset TxINT Pending */#define	ERR_RES		0x30	/* Error Reset */#define	RES_H_IUS	0x38	/* Reset highest IUS */#define	RES_Rx_CRC	0x40	/* Reset Rx CRC Checker */#define	RES_Tx_CRC	0x80	/* Reset Tx CRC Checker */#define	RES_EOM_L	0xC0	/* Reset EOM latch *//* Write Register 1 */#define	EXT_INT_ENAB	0x1	/* Ext Int Enable */#define	TxINT_ENAB	0x2	/* Tx Int Enable */#define	PAR_SPEC	0x4	/* Parity is special condition */#define	RxINT_DISAB	0	/* Rx Int Disable */#define	RxINT_FCERR	0x8	/* Rx Int on First Character Only or Error */#define	INT_ALL_Rx	0x10	/* Int on all Rx Characters or error */#define	INT_ERR_Rx	0x18	/* Int on error only */#define	WT_RDY_RT	0x20	/* Wait/Ready on R/T */#define	WT_FN_RDYFN	0x40	/* Wait/FN/Ready FN */#define	WT_RDY_ENAB	0x80	/* Wait/Ready Enable *//* Write Register #2 (Interrupt Vector) *//* Write Register 3 */#define	RxENABLE	0x1	/* Rx Enable */#define	SYNC_L_INH	0x2	/* Sync Character Load Inhibit */#define	ADD_SM		0x4	/* Address Search Mode (SDLC) */#define	RxCRC_ENAB	0x8	/* Rx CRC Enable */#define	ENT_HM		0x10	/* Enter Hunt Mode */#define	AUTO_ENAB	0x20	/* Auto Enables */#define	Rx5		0x0	/* Rx 5 Bits/Character */#define	Rx7		0x40	/* Rx 7 Bits/Character */#define	Rx6		0x80	/* Rx 6 Bits/Character */#define	Rx8		0xc0	/* Rx 8 Bits/Character *//* Write Register 4 */#define	PAR_ENA		0x1	/* Parity Enable */#define	PAR_EVEN	0x2	/* Parity Even/Odd* */#define	SYNC_ENAB	0	/* Sync Modes Enable */#define	SB1		0x4	/* 1 stop bit/char */#define	SB15		0x8	/* 1.5 stop bits/char */#define	SB2		0xc	/* 2 stop bits/char */#define	MONSYNC		0	/* 8 Bit Sync character */#define	BISYNC		0x10	/* 16 bit sync character */#define	SDLC		0x20	/* SDLC Mode (01111110 Sync Flag) */#define	EXTSYNC		0x30	/* External Sync Mode */#define	X1CLK		0x0	/* x1 clock mode */#define	X16CLK		0x40	/* x16 clock mode */#define	X32CLK		0x80	/* x32 clock mode */#define	X64CLK		0xC0	/* x64 clock mode *//* Write Register 5 */#define	TxCRC_ENAB	0x1	/* Tx CRC Enable */#define	RTS		0x2	/* RTS */#define	SDLC_CRC	0x4	/* SDLC/CRC-16 */#define	TxENAB		0x8	/* Tx Enable */#define	SND_BRK		0x10	/* Send Break */#define	Tx5		0x0	/* Tx 5 bits (or less)/character */#define	Tx7		0x20	/* Tx 7 bits/character */#define	Tx6		0x40	/* Tx 6 bits/character */#define	Tx8		0x60	/* Tx 8 bits/character */#define	DTR		0x80	/* DTR *//* Write Register 6 (Sync bits 0-7/SDLC Address Field) *//* Write Register 7 (Sync bits 8-15/SDLC 01111110) *//* Write Register 8 (transmit buffer) *//* Write Register 9 (Master interrupt control) */#define	VIS	1	/* Vector Includes Status */#define	NV	2	/* No Vector */#define	DLC	4	/* Disable Lower Chain */#define	MIE	8	/* Master Interrupt Enable */#define	STATHI	0x10	/* Status high */#define	NORESET	0	/* No reset on write to R9 */#define	CHRB	0x40	/* Reset channel B */#define	CHRA	0x80	/* Reset channel A */#define	FHWRES	0xc0	/* Force hardware reset *//* Write Register 10 (misc control bits) */#define	BIT6	1	/* 6 bit/8bit sync */#define	LOOPMODE 2	/* SDLC Loop mode */#define	ABUNDER	4	/* Abort/flag on SDLC xmit underrun */#define	MARKIDLE 8	/* Mark/flag on idle */#define	GAOP	0x10	/* Go active on poll */#define	NRZ	0	/* NRZ mode */#define	NRZI	0x20	/* NRZI mode */#define	FM1	0x40	/* FM1 (transition = 1) */#define	FM0	0x60	/* FM0 (transition = 0) */#define	CRCPS	0x80	/* CRC Preset I/O *//* Write Register 11 (Clock Mode control) */#define	TRxCXT	0	/* TRxC = Xtal output */#define	TRxCTC	1	/* TRxC = Transmit clock */#define	TRxCBR	2	/* TRxC = BR Generator Output */#define	TRxCDP	3	/* TRxC = DPLL output */#define	TRxCOI	4	/* TRxC O/I */#define	TCRTxCP	0	/* Transmit clock = RTxC pin */#define	TCTRxCP	8	/* Transmit clock = TRxC pin */#define	TCBR	0x10	/* Transmit clock = BR Generator output */#define	TCDPLL	0x18	/* Transmit clock = DPLL output */#define	RCRTxCP	0	/* Receive clock = RTxC pin */#define	RCTRxCP	0x20	/* Receive clock = TRxC pin */#define	RCBR	0x40	/* Receive clock = BR Generator output */#define	RCDPLL	0x60	/* Receive clock = DPLL output */#define	RTxCX	0x80	/* RTxC Xtal/No Xtal *//* Write Register 12 (lower byte of baud rate generator time constant) *//* Write Register 13 (upper byte of baud rate generator time constant) *//* Write Register 14 (Misc control bits) */#define	BRENABL	1	/* Baud rate generator enable */#define	BRSRC	2	/* Baud rate generator source */#define	DTRREQ	4	/* DTR/Request function */#define	AUTOECHO 8	/* Auto Echo */#define	LOOPBAK	0x10	/* Local loopback */#define	SEARCH	0x20	/* Enter search mode */#define	RMC	0x40	/* Reset missing clock */#define	DISDPLL	0x60	/* Disable DPLL */#define	SSBR	0x80	/* Set DPLL source = BR generator */#define	SSRTxC	0xa0	/* Set DPLL source = RTxC */#define	SFMM	0xc0	/* Set FM mode */#define	SNRZI	0xe0	/* Set NRZI mode *//* Write Register 15 (external/status interrupt control) */#define	ZCIE	2	/* Zero count IE */#define	DCDIE	8	/* DCD IE */#define	SYNCIE	0x10	/* Sync/hunt IE */#define	CTSIE	0x20	/* CTS IE */#define	TxUIE	0x40	/* Tx Underrun/EOM IE */#define	BRKIE	0x80	/* Break/Abort IE *//* Read Register 0 */#define	Rx_CH_AV	0x1	/* Rx Character Available */#define	ZCOUNT		0x2	/* Zero count */#define	Tx_BUF_EMP	0x4	/* Tx Buffer empty */#define	DCD		0x8	/* DCD */#define	SYNC		0x10	/* Sync/hunt */#define	CTS		0x20	/* CTS */#define	TxEOM		0x40	/* Tx underrun */#define	BRK_ABRT	0x80	/* Break/Abort *//* Read Register 1 */#define	ALL_SNT		0x1	/* All sent *//* Residue Data for 8 Rx bits/char programmed */#define	RES3		0x8	/* 0/3 */#define	RES4		0x4	/* 0/4 */#define	RES5		0xc	/* 0/5 */#define	RES6		0x2	/* 0/6 */#define	RES7		0xa	/* 0/7 */#define	RES8		0x6	/* 0/8 */#define	RES18		0xe	/* 1/8 */#define	RES28		0x0	/* 2/8 *//* Special Rx Condition Interrupts */#define	PAR_ERR		0x10	/* Parity error */#define	Rx_OVR		0x20	/* Rx Overrun Error */#define	CRC_ERR		0x40	/* CRC/Framing Error */#define	END_FR		0x80	/* End of Frame (SDLC) *//* Read Register 2 (channel b only) - Interrupt vector *//* Read Register 3 (interrupt pending register) ch a only */#define	CHBEXT	0x1		/* Channel B Ext/Stat IP */#define	CHBTxIP	0x2		/* Channel B Tx IP */#define	CHBRxIP	0x4		/* Channel B Rx IP */#define	CHAEXT	0x8		/* Channel A Ext/Stat IP */#define	CHATxIP	0x10		/* Channel A Tx IP */#define	CHARxIP	0x20		/* Channel A Rx IP *//* Read Register 8 (receive data register) *//* Read Register 10  (misc status bits) */#define	ONLOOP	2		/* On loop */#define	LOOPSEND 0x10		/* Loop sending */#define	CLK2MIS	0x40		/* Two clocks missing */#define	CLK1MIS	0x80		/* One clock missing *//* Read Register 12 (lower byte of baud rate generator constant) *//* Read Register 13 (upper byte of baud rate generator constant) *//* Read Register 15 (value of WR 15) *//* Misc inlines */static inline void ZS_CLEARERR(struct sgi_zschannel *channel){	volatile unsigned char junk;	udelay(2);	channel->control = ERR_RES;	if (ioc_icontrol)		junk = ioc_icontrol->istat0;}static inline void ZS_CLEARFIFO(struct sgi_zschannel *channel){	volatile unsigned char junk;	udelay(2);	junk = channel->data;	udelay(2);	if (ioc_icontrol)		junk = ioc_icontrol->istat0;	junk = channel->data;	udelay(2);	if (ioc_icontrol)		junk = ioc_icontrol->istat0;	junk = channel->data;	udelay(2);	if (ioc_icontrol)		junk = ioc_icontrol->istat0;}#if 0#define ZS_CLEARERR(channel)    (channel->control = ERR_RES)#define ZS_CLEARFIFO(channel)   do { volatile unsigned char garbage; \				     garbage = channel->data; \				     udelay(2); \				     garbage = channel->data; \				     udelay(2); \				     garbage = channel->data; \				     udelay(2); } while(0)#endif#endif /* !(_SPARC_SERIAL_H) */