index_title=PPPoE選項index_eadsl=The RP-PPPoE command $1 was not found on your system or is not valid. Maybe it is not installed, or your <a href='$2'>module configuration</a> is incorrect.index_econfig=The RP-PPPoE PPPoE configuration file $1 was not found on your system. Maybe it is not installed, or your <a href='$2'>module configuration</a> is incorrect.index_emodem=The current configuration file is for a modem on Redhat Linux, not an PPPoE connection. Use the <a href='$2'>module configuration</a> page to specify one of the other <tt>ifcfg-ppp*</tt> files in $1, or one that does not exist yet so that them module can create it for you.index_stop=關閉PPPoEindex_stopdesc=PPPoE 連接目前處于活動狀態(tài)，其IP地址是 $1. 點擊該按鈕將停止該連接.index_start=啟動 PPPoEindex_startdesc= PPPoE連接目前沒有啟動，請單擊此按鈕啟動它index_boot=系統(tǒng)啟動時打開index_bootdesc=Change this option to control whether your PPPoE connection is brought up at boot time or not.index_return=PPPoE選項index_version=RP-PPPoE 版本 $1index_esetup=The Redhat PPPoE configuration file $1 does not exist on your system. However, this module can set it up for you with basic defaults by clicking the button below.index_setup=Setup configuration fileindex_cancel=取消連接index_canceldesc= iServer目前正在試圖建立PPPoE連接，請單擊此按鈕取消之index_header=PPPoE 選項index_desc=The settings below apply to any new PPPoE connection started by your system. If you change them, the connection must be shut down and re-started for the modifications to take effect.index_eth=以太接口index_other=其它..index_demand=需要時連接?index_timeout=是, 超時時間為index_secs=秒index_user=登錄用戶名index_sec=登錄口令字index_dns=從 ISP 獲取 DNS 配置?index_save=保存index_mss=限制分組大小?index_psize=限制在index_bytes=字節(jié)內index_fw=Firewall to activate on connectionindex_fw_none=無index_fw_standalone=For single hostindex_fw_masquerade=For NAT gatewayindex_connect=嘗試連接的時間index_forever=永遠bifc_create=編輯接口ifcs_title=網絡接口start_err=啟動PPPoE 連接時失敗start_title=啟動 PPPoEstart_ip= PPPoE 連接已經建立，IP地址: $1.start_demand=Because connect on demand mode is enabled, your PPPoE connection will only be started when needed.start_bg=PPPoE連接在20秒內沒有建立成功，將轉入到后臺重新嘗試。save_err=保存PPPoE 配置信息失敗save_eeth=Missing or invalid-looking ethernet interfacesave_etimeout=Missing or invalid on-demand timeoutsave_euser=Missing or invalid usernamesave_econnect=Missing or invalid connection timeoutsave_emss=Missing or invalid maximum packet sizesave_title=保存配置save_desc= PPPoE 配置已經成功保存，請重新啟動PPPoE連接以便新的配置生效.stop_err=關閉PPPoE 連接時失敗stop_title=關閉PPPoEstop_ok=PPPoE連接關閉成功.stop_failed=由于某種原因PPPoE連接仍然活動!log_save=Saved client configurationlog_stop=Shut down PPPoElog_start=Started up PPPoElog_bootup=Enabled PPPoE at boot timelog_bootdown=Disabled PPPoE at boot timelog_setup=Set up default configuration