?? pwm.h
字號:
//*****************************************************************************
//
// pwm.h - API function protoypes for Pulse Width Modulation (PWM) ports
//
// Copyright (c) 2005-2010 Texas Instruments Incorporated. All rights reserved.
// Software License Agreement
//
// Texas Instruments (TI) is supplying this software for use solely and
// exclusively on TI's microcontroller products. The software is owned by
// TI and/or its suppliers, and is protected under applicable copyright
// laws. You may not combine this software with "viral" open-source
// software in order to form a larger program.
//
// THIS SOFTWARE IS PROVIDED "AS IS" AND WITH ALL FAULTS.
// NO WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT
// NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
// A PARTICULAR PURPOSE APPLY TO THIS SOFTWARE. TI SHALL NOT, UNDER ANY
// CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
// DAMAGES, FOR ANY REASON WHATSOEVER.
//
// This is part of revision 5821 of the Stellaris Peripheral Driver Library.
//
//*****************************************************************************
#ifndef __PWM_H__
#define __PWM_H__
//*****************************************************************************
//
// If building with a C++ compiler, make all of the definitions in this header
// have a C binding.
//
//*****************************************************************************
#ifdef __cplusplus
extern "C"
{
#endif
//*****************************************************************************
//
// The following defines are passed to PWMGenConfigure() as the ulConfig
// parameter and specify the configuration of the PWM generator.
//
//*****************************************************************************
#define PWM_GEN_MODE_DOWN 0x00000000 // Down count mode
#define PWM_GEN_MODE_UP_DOWN 0x00000002 // Up/Down count mode
#define PWM_GEN_MODE_SYNC 0x00000038 // Synchronous updates
#define PWM_GEN_MODE_NO_SYNC 0x00000000 // Immediate updates
#define PWM_GEN_MODE_DBG_RUN 0x00000004 // Continue running in debug mode
#define PWM_GEN_MODE_DBG_STOP 0x00000000 // Stop running in debug mode
#define PWM_GEN_MODE_FAULT_LATCHED \
0x00040000 // Fault is latched
#define PWM_GEN_MODE_FAULT_UNLATCHED \
0x00000000 // Fault is not latched
#define PWM_GEN_MODE_FAULT_MINPER \
0x00020000 // Enable min fault period
#define PWM_GEN_MODE_FAULT_NO_MINPER \
0x00000000 // Disable min fault period
#define PWM_GEN_MODE_FAULT_EXT 0x00010000 // Enable extended fault support
#define PWM_GEN_MODE_FAULT_LEGACY \
0x00000000 // Disable extended fault support
#define PWM_GEN_MODE_DB_NO_SYNC 0x00000000 // Deadband updates occur
// immediately
#define PWM_GEN_MODE_DB_SYNC_LOCAL \
0x0000A800 // Deadband updates locally
// synchronized
#define PWM_GEN_MODE_DB_SYNC_GLOBAL \
0x0000FC00 // Deadband updates globally
// synchronized
#define PWM_GEN_MODE_GEN_NO_SYNC \
0x00000000 // Generator mode updates occur
// immediately
#define PWM_GEN_MODE_GEN_SYNC_LOCAL \
0x00000280 // Generator mode updates locally
// synchronized
#define PWM_GEN_MODE_GEN_SYNC_GLOBAL \
0x000003C0 // Generator mode updates globally
// synchronized
//*****************************************************************************
//
// Defines for enabling, disabling, and clearing PWM generator interrupts and
// triggers.
//
//*****************************************************************************
#define PWM_INT_CNT_ZERO 0x00000001 // Int if COUNT = 0
#define PWM_INT_CNT_LOAD 0x00000002 // Int if COUNT = LOAD
#define PWM_INT_CNT_AU 0x00000004 // Int if COUNT = CMPA U
#define PWM_INT_CNT_AD 0x00000008 // Int if COUNT = CMPA D
#define PWM_INT_CNT_BU 0x00000010 // Int if COUNT = CMPA U
#define PWM_INT_CNT_BD 0x00000020 // Int if COUNT = CMPA D
#define PWM_TR_CNT_ZERO 0x00000100 // Trig if COUNT = 0
#define PWM_TR_CNT_LOAD 0x00000200 // Trig if COUNT = LOAD
#define PWM_TR_CNT_AU 0x00000400 // Trig if COUNT = CMPA U
#define PWM_TR_CNT_AD 0x00000800 // Trig if COUNT = CMPA D
#define PWM_TR_CNT_BU 0x00001000 // Trig if COUNT = CMPA U
#define PWM_TR_CNT_BD 0x00002000 // Trig if COUNT = CMPA D
//*****************************************************************************
//
// Defines for enabling, disabling, and clearing PWM interrupts.
//
//*****************************************************************************
#define PWM_INT_GEN_0 0x00000001 // Generator 0 interrupt
#define PWM_INT_GEN_1 0x00000002 // Generator 1 interrupt
#define PWM_INT_GEN_2 0x00000004 // Generator 2 interrupt
#define PWM_INT_GEN_3 0x00000008 // Generator 3 interrupt
#ifndef DEPRECATED
#define PWM_INT_FAULT 0x00010000 // Fault interrupt
#endif
#define PWM_INT_FAULT0 0x00010000 // Fault0 interrupt
#define PWM_INT_FAULT1 0x00020000 // Fault1 interrupt
#define PWM_INT_FAULT2 0x00040000 // Fault2 interrupt
#define PWM_INT_FAULT3 0x00080000 // Fault3 interrupt
#define PWM_INT_FAULT_M 0x000F0000 // Fault interrupt source mask
//*****************************************************************************
//
// Defines to identify the generators within a module.
//
//*****************************************************************************
#define PWM_GEN_0 0x00000040 // Offset address of Gen0
#define PWM_GEN_1 0x00000080 // Offset address of Gen1
#define PWM_GEN_2 0x000000C0 // Offset address of Gen2
#define PWM_GEN_3 0x00000100 // Offset address of Gen3
#define PWM_GEN_0_BIT 0x00000001 // Bit-wise ID for Gen0
#define PWM_GEN_1_BIT 0x00000002 // Bit-wise ID for Gen1
#define PWM_GEN_2_BIT 0x00000004 // Bit-wise ID for Gen2
#define PWM_GEN_3_BIT 0x00000008 // Bit-wise ID for Gen3
#define PWM_GEN_EXT_0 0x00000800 // Offset of Gen0 ext address range
#define PWM_GEN_EXT_1 0x00000880 // Offset of Gen1 ext address range
#define PWM_GEN_EXT_2 0x00000900 // Offset of Gen2 ext address range
#define PWM_GEN_EXT_3 0x00000980 // Offset of Gen3 ext address range
//*****************************************************************************
//
// Defines to identify the outputs within a module.
//
//*****************************************************************************
#define PWM_OUT_0 0x00000040 // Encoded offset address of PWM0
#define PWM_OUT_1 0x00000041 // Encoded offset address of PWM1
#define PWM_OUT_2 0x00000082 // Encoded offset address of PWM2
#define PWM_OUT_3 0x00000083 // Encoded offset address of PWM3
#define PWM_OUT_4 0x000000C4 // Encoded offset address of PWM4
#define PWM_OUT_5 0x000000C5 // Encoded offset address of PWM5
#define PWM_OUT_6 0x00000106 // Encoded offset address of PWM6
#define PWM_OUT_7 0x00000107 // Encoded offset address of PWM7
#define PWM_OUT_0_BIT 0x00000001 // Bit-wise ID for PWM0
#define PWM_OUT_1_BIT 0x00000002 // Bit-wise ID for PWM1
#define PWM_OUT_2_BIT 0x00000004 // Bit-wise ID for PWM2
#define PWM_OUT_3_BIT 0x00000008 // Bit-wise ID for PWM3
#define PWM_OUT_4_BIT 0x00000010 // Bit-wise ID for PWM4
#define PWM_OUT_5_BIT 0x00000020 // Bit-wise ID for PWM5
#define PWM_OUT_6_BIT 0x00000040 // Bit-wise ID for PWM6
#define PWM_OUT_7_BIT 0x00000080 // Bit-wise ID for PWM7
//*****************************************************************************
//
// Defines to identify each of the possible fault trigger conditions in
// PWM_FAULT_GROUP_0.
//
//*****************************************************************************
#define PWM_FAULT_GROUP_0 0
#define PWM_FAULT_FAULT0 0x00000001
#define PWM_FAULT_FAULT1 0x00000002
#define PWM_FAULT_FAULT2 0x00000004
#define PWM_FAULT_FAULT3 0x00000008
#define PWM_FAULT_ACMP0 0x00010000
#define PWM_FAULT_ACMP1 0x00020000
#define PWM_FAULT_ACMP2 0x00040000
//*****************************************************************************
//
// Defines to identify each of the possible fault trigger conditions in
// PWM_FAULT_GROUP_1.
//
//*****************************************************************************
#define PWM_FAULT_GROUP_1 1
//*****************************************************************************
//
// Defines to identify the sense of each of the external FAULTn signals
//
//*****************************************************************************
#define PWM_FAULT0_SENSE_HIGH 0x00000000
#define PWM_FAULT0_SENSE_LOW 0x00000001
#define PWM_FAULT1_SENSE_HIGH 0x00000000
#define PWM_FAULT1_SENSE_LOW 0x00000002
#define PWM_FAULT2_SENSE_HIGH 0x00000000
#define PWM_FAULT2_SENSE_LOW 0x00000004
#define PWM_FAULT3_SENSE_HIGH 0x00000000
#define PWM_FAULT3_SENSE_LOW 0x00000008
//*****************************************************************************
//
// API Function prototypes
//
//*****************************************************************************
extern void PWMGenConfigure(unsigned long ulBase, unsigned long ulGen,
unsigned long ulConfig);
extern void PWMGenPeriodSet(unsigned long ulBase, unsigned long ulGen,
unsigned long ulPeriod);
extern unsigned long PWMGenPeriodGet(unsigned long ulBase,
unsigned long ulGen);
extern void PWMGenEnable(unsigned long ulBase, unsigned long ulGen);
extern void PWMGenDisable(unsigned long ulBase, unsigned long ulGen);
extern void PWMPulseWidthSet(unsigned long ulBase, unsigned long ulPWMOut,
unsigned long ulWidth);
extern unsigned long PWMPulseWidthGet(unsigned long ulBase,
unsigned long ulPWMOut);
extern void PWMDeadBandEnable(unsigned long ulBase, unsigned long ulGen,
unsigned short usRise, unsigned short usFall);
extern void PWMDeadBandDisable(unsigned long ulBase, unsigned long ulGen);
extern void PWMSyncUpdate(unsigned long ulBase, unsigned long ulGenBits);
extern void PWMSyncTimeBase(unsigned long ulBase, unsigned long ulGenBits);
extern void PWMOutputState(unsigned long ulBase, unsigned long ulPWMOutBits,
tBoolean bEnable);
extern void PWMOutputInvert(unsigned long ulBase, unsigned long ulPWMOutBits,
tBoolean bInvert);
extern void PWMOutputFaultLevel(unsigned long ulBase,
unsigned long ulPWMOutBits,
tBoolean bDriveHigh);
extern void PWMOutputFault(unsigned long ulBase, unsigned long ulPWMOutBits,
tBoolean bFaultSuppress);
extern void PWMGenIntRegister(unsigned long ulBase, unsigned long ulGen,
void (*pfnIntHandler)(void));
extern void PWMGenIntUnregister(unsigned long ulBase, unsigned long ulGen);
extern void PWMFaultIntRegister(unsigned long ulBase,
void (*pfnIntHandler)(void));
extern void PWMFaultIntUnregister(unsigned long ulBase);
extern void PWMGenIntTrigEnable(unsigned long ulBase, unsigned long ulGen,
unsigned long ulIntTrig);
extern void PWMGenIntTrigDisable(unsigned long ulBase, unsigned long ulGen,
unsigned long ulIntTrig);
extern unsigned long PWMGenIntStatus(unsigned long ulBase, unsigned long ulGen,
tBoolean bMasked);
extern void PWMGenIntClear(unsigned long ulBase, unsigned long ulGen,
unsigned long ulInts);
extern void PWMIntEnable(unsigned long ulBase, unsigned long ulGenFault);
extern void PWMIntDisable(unsigned long ulBase, unsigned long ulGenFault);
extern void PWMFaultIntClear(unsigned long ulBase);
extern unsigned long PWMIntStatus(unsigned long ulBase, tBoolean bMasked);
extern void PWMFaultIntClearExt(unsigned long ulBase,
unsigned long ulFaultInts);
extern void PWMGenFaultConfigure(unsigned long ulBase, unsigned long ulGen,
unsigned long ulMinFaultPeriod,
unsigned long ulFaultSenses);
extern void PWMGenFaultTriggerSet(unsigned long ulBase, unsigned long ulGen,
unsigned long ulGroup,
unsigned long ulFaultTriggers);
extern unsigned long PWMGenFaultTriggerGet(unsigned long ulBase,
unsigned long ulGen,
unsigned long ulGroup);
extern unsigned long PWMGenFaultStatus(unsigned long ulBase,
unsigned long ulGen,
unsigned long ulGroup);
extern void PWMGenFaultClear(unsigned long ulBase, unsigned long ulGen,
unsigned long ulGroup,
unsigned long ulFaultTriggers);
//*****************************************************************************
//
// Mark the end of the C bindings section for C++ compilers.
//
//*****************************************************************************
#ifdef __cplusplus
}
#endif
#endif // __PWM_H__
?? 快捷鍵說明
復(fù)制代碼
Ctrl + C
搜索代碼
Ctrl + F
全屏模式
F11
切換主題
Ctrl + Shift + D
顯示快捷鍵
?
增大字號
Ctrl + =
減小字號
Ctrl + -