*/
uint8_t CAN_GetReceiveErrorCounter(CAN_TypeDef* CANx)
{
  uint8_t counter=0;
  
  /* Check the parameters */
  assert_param(IS_CAN_ALL_PERIPH(CANx));
  
  /* Get the Receive Error Counter*/
  counter = (uint8_t)((CANx->ESR & CAN_ESR_REC)>> 24);
  
  /* Return the Receive Error Counter*/
  return counter;
}


/**
  * @brief  Returns the LSB of the 9-bit CANx Transmit Error Counter(TEC).
  * @param  CANx:   where x can be 1 or 2 to to select the CAN peripheral.  
  * @retval LSB of the 9-bit CAN Transmit Error Counter. 
  */
uint8_t CAN_GetLSBTransmitErrorCounter(CAN_TypeDef* CANx)
{
  uint8_t counter=0;
  
  /* Check the parameters */
  assert_param(IS_CAN_ALL_PERIPH(CANx));
  
  /* Get the LSB of the 9-bit CANx Transmit Error Counter(TEC) */
  counter = (uint8_t)((CANx->ESR & CAN_ESR_TEC)>> 16);
  
  /* Return the LSB of the 9-bit CANx Transmit Error Counter(TEC) */
  return counter;
}


/**
  * @brief  Enables or disables the specified CANx interrupts.
  * @param  CANx:   where x can be 1 or 2 to to select the CAN peripheral.
  * @param  CAN_IT: specifies the CAN interrupt sources to be enabled or disabled.
  *                 This parameter can be: 
  *                 - CAN_IT_TME, 
  *                 - CAN_IT_FMP0, 
  *                 - CAN_IT_FF0,
  *                 - CAN_IT_FOV0, 
  *                 - CAN_IT_FMP1, 
  *                 - CAN_IT_FF1,
  *                 - CAN_IT_FOV1, 
  *                 - CAN_IT_EWG, 
  *                 - CAN_IT_EPV,
  *                 - CAN_IT_LEC, 
  *                 - CAN_IT_ERR, 
  *                 - CAN_IT_WKU or 
  *                 - CAN_IT_SLK.
  * @param  NewState: new state of the CAN interrupts.
  *                   This parameter can be: ENABLE or DISABLE.
  * @retval None.
  */
void CAN_ITConfig(CAN_TypeDef* CANx, uint32_t CAN_IT, FunctionalState NewState)
{
  /* Check the parameters */
  assert_param(IS_CAN_ALL_PERIPH(CANx));
  assert_param(IS_CAN_IT(CAN_IT));
  assert_param(IS_FUNCTIONAL_STATE(NewState));

  if (NewState != DISABLE)
  {
    /* Enable the selected CANx interrupt */
    CANx->IER |= CAN_IT;
  }
  else
  {
    /* Disable the selected CANx interrupt */
    CANx->IER &= ~CAN_IT;
  }
}
/**
  * @brief  Checks whether the specified CAN flag is set or not.
  * @param  CANx:     where x can be 1 or 2 to to select the CAN peripheral.
  * @param  CAN_FLAG: specifies the flag to check.
  *                   This parameter can be one of the following flags: 
  *                  - CAN_FLAG_EWG
  *                  - CAN_FLAG_EPV 
  *                  - CAN_FLAG_BOF
  *                  - CAN_FLAG_RQCP0
  *                  - CAN_FLAG_RQCP1
  *                  - CAN_FLAG_RQCP2
  *                  - CAN_FLAG_FMP1   
  *                  - CAN_FLAG_FF1       
  *                  - CAN_FLAG_FOV1   
  *                  - CAN_FLAG_FMP0   
  *                  - CAN_FLAG_FF0       
  *                  - CAN_FLAG_FOV0   
  *                  - CAN_FLAG_WKU 
  *                  - CAN_FLAG_SLAK  
  *                  - CAN_FLAG_LEC       
  * @retval The new state of CAN_FLAG (SET or RESET).
  */
FlagStatus CAN_GetFlagStatus(CAN_TypeDef* CANx, uint32_t CAN_FLAG)
{
  FlagStatus bitstatus = RESET;
  
  /* Check the parameters */
  assert_param(IS_CAN_ALL_PERIPH(CANx));
  assert_param(IS_CAN_GET_FLAG(CAN_FLAG));
  

  if((CAN_FLAG & CAN_FLAGS_ESR) != (uint32_t)RESET)
  { 
    /* Check the status of the specified CAN flag */
    if ((CANx->ESR & (CAN_FLAG & 0x000FFFFF)) != (uint32_t)RESET)
    { 
      /* CAN_FLAG is set */
      bitstatus = SET;
    }
    else
    { 
      /* CAN_FLAG is reset */
      bitstatus = RESET;
    }
  }
  else if((CAN_FLAG & CAN_FLAGS_MSR) != (uint32_t)RESET)
  { 
    /* Check the status of the specified CAN flag */
    if ((CANx->MSR & (CAN_FLAG & 0x000FFFFF)) != (uint32_t)RESET)
    { 
      /* CAN_FLAG is set */
      bitstatus = SET;
    }
    else
    { 
      /* CAN_FLAG is reset */
      bitstatus = RESET;
    }
  }
  else if((CAN_FLAG & CAN_FLAGS_TSR) != (uint32_t)RESET)
  { 
    /* Check the status of the specified CAN flag */
    if ((CANx->TSR & (CAN_FLAG & 0x000FFFFF)) != (uint32_t)RESET)
    { 
      /* CAN_FLAG is set */
      bitstatus = SET;
    }
    else
    { 
      /* CAN_FLAG is reset */
      bitstatus = RESET;
    }
  }
  else if((CAN_FLAG & CAN_FLAGS_RF0R) != (uint32_t)RESET)
  { 
    /* Check the status of the specified CAN flag */
    if ((CANx->RF0R & (CAN_FLAG & 0x000FFFFF)) != (uint32_t)RESET)
    { 
      /* CAN_FLAG is set */
      bitstatus = SET;
    }
    else
    { 
      /* CAN_FLAG is reset */
      bitstatus = RESET;
    }
  }
  else /* If(CAN_FLAG & CAN_FLAGS_RF1R != (uint32_t)RESET) */
  { 
    /* Check the status of the specified CAN flag */
    if ((uint32_t)(CANx->RF1R & (CAN_FLAG & 0x000FFFFF)) != (uint32_t)RESET)
    { 
      /* CAN_FLAG is set */
      bitstatus = SET;
    }
    else
    { 
      /* CAN_FLAG is reset */
      bitstatus = RESET;
    }
  }
  /* Return the CAN_FLAG status */
  return  bitstatus;
}

/**
  * @brief  Clears the CAN's pending flags.
  * @param  CANx:     where x can be 1 or 2 to to select the CAN peripheral.
  * @param  CAN_FLAG: specifies the flag to clear.
  *                   This parameter can be one of the following flags: 
  *                    - CAN_FLAG_RQCP0
  *                    - CAN_FLAG_RQCP1
  *                    - CAN_FLAG_RQCP2
  *                    - CAN_FLAG_FF1       
  *                    - CAN_FLAG_FOV1   
  *                    - CAN_FLAG_FF0       
  *                    - CAN_FLAG_FOV0   
  *                    - CAN_FLAG_WKU   
  *                    - CAN_FLAG_SLAK    
  *                    - CAN_FLAG_LEC       
  * @retval None.
  */
void CAN_ClearFlag(CAN_TypeDef* CANx, uint32_t CAN_FLAG)
{
  uint32_t flagtmp=0;
  /* Check the parameters */
  assert_param(IS_CAN_ALL_PERIPH(CANx));
  assert_param(IS_CAN_CLEAR_FLAG(CAN_FLAG));
  
  if (CAN_FLAG == CAN_FLAG_LEC) /* ESR register */
  {
    /* Clear the selected CAN flags */
    CANx->ESR = (uint32_t)RESET;
  }
  else /* MSR or TSR or RF0R or RF1R */
  {
    flagtmp = CAN_FLAG & 0x000FFFFF;

    if ((CAN_FLAG & CAN_FLAGS_RF0R)!=(uint32_t)RESET)
    {
      /* Receive Flags */
      CANx->RF0R = (uint32_t)(flagtmp);
    }
    else if ((CAN_FLAG & CAN_FLAGS_RF1R)!=(uint32_t)RESET)
    {
      /* Receive Flags */
      CANx->RF1R = (uint32_t)(flagtmp);
    }
    else if ((CAN_FLAG & CAN_FLAGS_TSR)!=(uint32_t)RESET)
    {
      /* Transmit Flags */
      CANx->TSR = (uint32_t)(flagtmp);
    }
    else /* If((CAN_FLAG & CAN_FLAGS_MSR)!=(uint32_t)RESET) */
    {
      /* Operating mode Flags */
      CANx->MSR = (uint32_t)(flagtmp);
    }
  }
}

/**
  * @brief  Checks whether the specified CANx interrupt has occurred or not.
  * @param  CANx:    where x can be 1 or 2 to to select the CAN peripheral.
  * @param  CAN_IT:  specifies the CAN interrupt source to check.
  *                  This parameter can be one of the following flags: 
  *                 -  CAN_IT_TME               
  *                 -  CAN_IT_FMP0              
  *                 -  CAN_IT_FF0               
  *                 -  CAN_IT_FOV0              
  *                 -  CAN_IT_FMP1              
  *                 -  CAN_IT_FF1               
  *                 -  CAN_IT_FOV1              
  *                 -  CAN_IT_WKU  
  *                 -  CAN_IT_SLK  
  *                 -  CAN_IT_EWG    
  *                 -  CAN_IT_EPV    
  *                 -  CAN_IT_BOF    
  *                 -  CAN_IT_LEC    
  *                 -  CAN_IT_ERR 
  * @retval The current state of CAN_IT (SET or RESET).
  */
ITStatus CAN_GetITStatus(CAN_TypeDef* CANx, uint32_t CAN_IT)
{
  ITStatus itstatus = RESET;
  /* Check the parameters */
  assert_param(IS_CAN_ALL_PERIPH(CANx));
  assert_param(IS_CAN_IT(CAN_IT));
  
  /* check the enable interrupt bit */
 if((CANx->IER & CAN_IT) != RESET)
 {
   /* in case the Interrupt is enabled, .... */
    switch (CAN_IT)
    {
      case CAN_IT_TME:
               /* Check CAN_TSR_RQCPx bits */
	             itstatus = CheckITStatus(CANx->TSR, CAN_TSR_RQCP0|CAN_TSR_RQCP1|CAN_TSR_RQCP2);  
	      break;
      case CAN_IT_FMP0:
               /* Check CAN_RF0R_FMP0 bit */
	             itstatus = CheckITStatus(CANx->RF0R, CAN_RF0R_FMP0);  
	      break;
      case CAN_IT_FF0:
               /* Check CAN_RF0R_FULL0 bit */
               itstatus = CheckITStatus(CANx->RF0R, CAN_RF0R_FULL0);  
	      break;
      case CAN_IT_FOV0:
               /* Check CAN_RF0R_FOVR0 bit */
               itstatus = CheckITStatus(CANx->RF0R, CAN_RF0R_FOVR0);  
	      break;
      case CAN_IT_FMP1:
               /* Check CAN_RF1R_FMP1 bit */
               itstatus = CheckITStatus(CANx->RF1R, CAN_RF1R_FMP1);  
	      break;
      case CAN_IT_FF1:
               /* Check CAN_RF1R_FULL1 bit */
	             itstatus = CheckITStatus(CANx->RF1R, CAN_RF1R_FULL1);  
	      break;
      case CAN_IT_FOV1:
               /* Check CAN_RF1R_FOVR1 bit */
	             itstatus = CheckITStatus(CANx->RF1R, CAN_RF1R_FOVR1);  
	      break;
      case CAN_IT_WKU:
               /* Check CAN_MSR_WKUI bit */
               itstatus = CheckITStatus(CANx->MSR, CAN_MSR_WKUI);  
	      break;
      case CAN_IT_SLK:
               /* Check CAN_MSR_SLAKI bit */
	             itstatus = CheckITStatus(CANx->MSR, CAN_MSR_SLAKI);  
	      break;
      case CAN_IT_EWG:
               /* Check CAN_ESR_EWGF bit */
	             itstatus = CheckITStatus(CANx->ESR, CAN_ESR_EWGF);  
	      break;
      case CAN_IT_EPV:
               /* Check CAN_ESR_EPVF bit */
	             itstatus = CheckITStatus(CANx->ESR, CAN_ESR_EPVF);  
	      break;
      case CAN_IT_BOF:
               /* Check CAN_ESR_BOFF bit */
	             itstatus = CheckITStatus(CANx->ESR, CAN_ESR_BOFF);  
	      break;
      case CAN_IT_LEC:
               /* Check CAN_ESR_LEC bit */
	             itstatus = CheckITStatus(CANx->ESR, CAN_ESR_LEC);  
	      break;
      case CAN_IT_ERR:
               /* Check CAN_MSR_ERRI bit */ 
               itstatus = CheckITStatus(CANx->MSR, CAN_MSR_ERRI); 
	      break;
      default :
               /* in case of error, return RESET */
              itstatus = RESET;
              break;
    }
  }
  else
  {
   /* in case the Interrupt is not enabled, return RESET */
    itstatus  = RESET;
  }
  
  /* Return the CAN_IT status */
  return  itstatus;
}

/**
  * @brief  Clears the CANx's interrupt pending bits.
  * @param  CANx:    where x can be 1 or 2 to to select the CAN peripheral.
  * @param  CAN_IT: specifies the interrupt pending bit to clear.
  *                  -  CAN_IT_TME                     
  *                  -  CAN_IT_FF0               
  *                  -  CAN_IT_FOV0                     
  *                  -  CAN_IT_FF1               
  *                  -  CAN_IT_FOV1              
  *                  -  CAN_IT_WKU  
  *                  -  CAN_IT_SLK  
  *                  -  CAN_IT_EWG    
  *                  -  CAN_IT_EPV    
  *                  -  CAN_IT_BOF    
  *                  -  CAN_IT_LEC    
  *                  -  CAN_IT_ERR 
  * @retval None.
  */
void CAN_ClearITPendingBit(CAN_TypeDef* CANx, uint32_t CAN_IT)
{
  /* Check the parameters */
  assert_param(IS_CAN_ALL_PERIPH(CANx));
  assert_param(IS_CAN_CLEAR_IT(CAN_IT));

  switch (CAN_IT)
  {
      case CAN_IT_TME:
              /* Clear CAN_TSR_RQCPx (rc_w1)*/
	      CANx->TSR = CAN_TSR_RQCP0|CAN_TSR_RQCP1|CAN_TSR_RQCP2;  
	      break;
      case CAN_IT_FF0:
              /* Clear CAN_RF0R_FULL0 (rc_w1)*/
	      CANx->RF0R = CAN_RF0R_FULL0; 
	      break;
      case CAN_IT_FOV0:
              /* Clear CAN_RF0R_FOVR0 (rc_w1)*/
	      CANx->RF0R = CAN_RF0R_FOVR0; 
	      break;
      case CAN_IT_FF1:
              /* Clear CAN_RF1R_FULL1 (rc_w1)*/
	      CANx->RF1R = CAN_RF1R_FULL1;  
	      break;
      case CAN_IT_FOV1:
              /* Clear CAN_RF1R_FOVR1 (rc_w1)*/
	      CANx->RF1R = CAN_RF1R_FOVR1; 
	      break;
      case CAN_IT_WKU:
              /* Clear CAN_MSR_WKUI (rc_w1)*/
	      CANx->MSR = CAN_MSR_WKUI;  
	      break;
      case CAN_IT_SLK:
              /* Clear CAN_MSR_SLAKI (rc_w1)*/ 
	      CANx->MSR = CAN_MSR_SLAKI;   
	      break;
      case CAN_IT_EWG:
              /* Clear CAN_MSR_ERRI (rc_w1) */
	      CANx->MSR = CAN_MSR_ERRI;
              /* Note : the corresponding Flag is cleared by hardware depending 
                        of the CAN Bus status*/ 
	      break;
      case CAN_IT_EPV:
              /* Clear CAN_MSR_ERRI (rc_w1) */
	      CANx->MSR = CAN_MSR_ERRI; 
              /* Note : the corresponding Flag is cleared by hardware depending 
                        of the CAN Bus status*/
	      break;
      case CAN_IT_BOF:
              /* Clear CAN_MSR_ERRI (rc_w1) */ 
	      CANx->MSR = CAN_MSR_ERRI; 
              /* Note : the corresponding Flag is cleared by hardware depending 
                        of the CAN Bus status*/
	      break;
      case CAN_IT_LEC:
              /*  Clear LEC bits */
	      CANx->ESR = RESET; 
              /* Clear CAN_MSR_ERRI (rc_w1) */
	      CANx->MSR = CAN_MSR_ERRI; 
	      break;
      case CAN_IT_ERR:
              /*Clear LEC bits */
	      CANx->ESR = RESET; 
              /* Clear CAN_MSR_ERRI (rc_w1) */
	      CANx->MSR = CAN_MSR_ERRI; 
	      /* Note : BOFF, EPVF and EWGF Flags are cleared by hardware depending 
                  of the CAN Bus status*/
	      break;
      default :
	      break;
   }
}

/**
  * @brief  Checks whether the CAN interrupt has occurred or not.
  * @param  CAN_Reg: specifies the CAN interrupt register to check.
  * @param  It_Bit:  specifies the interrupt source bit to check.
  * @retval The new state of the CAN Interrupt (SET or RESET).
  */
static ITStatus CheckITStatus(uint32_t CAN_Reg, uint32_t It_Bit)
{
  ITStatus pendingbitstatus = RESET;
  
  if ((CAN_Reg & It_Bit) != (uint32_t)RESET)
  {
    /* CAN_IT is set */
    pendingbitstatus = SET;
  }
  else
  {
    /* CAN_IT is reset */
    pendingbitstatus = RESET;
  }
  return pendingbitstatus;
}


/**
  * @}
  */

/**
  * @}
  */

/**
  * @}
  */

/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/