?? 2410lib.c
字號:
#include "def.h"
#include "option.h"
#include "2410addr.h"
#include "2410lib.h"
#include "2410slib.h"
#include <stdarg.h>
#include <string.h>
#include <stdlib.h>
#include <stdio.h>
#include <ctype.h>
extern char Image$$RW$$Limit[];
void *mallocPt=Image$$RW$$Limit;
//===========================[ SYSTEM ]===================================================
//static int delayLoopCount = 400;
static int delayLoopCount = FCLK/10000/10;
void Delay(int time)
{
// time=0: adjust the Delay function by WatchDog timer.
// time>0: the number of loop time
// resolution of time is 100us.
int i,adjust=0;
if(time==0)
{
time = 200;
adjust = 1;
delayLoopCount = 400;
//PCLK/1M,Watch-dog disable,1/64,interrupt disable,reset disable
rWTCON = ((PCLK/1000000-1)<<8)|(2<<3);
rWTDAT = 0xffff; //for first update
rWTCNT = 0xffff; //resolution=64us @any PCLK
rWTCON = ((PCLK/1000000-1)<<8)|(2<<3)|(1<<5); //Watch-dog timer start
}
for(;time>0;time--)
for(i=0;i<delayLoopCount;i++);
if(adjust==1)
{
rWTCON = ((PCLK/1000000-1)<<8)|(2<<3); //Watch-dog timer stop
i = 0xffff - rWTCNT; //1count->64us, 200*400 cycle runtime = 64*i us
delayLoopCount = 8000000/(i*64); //200*400:64*i=1*x:100 -> x=80000*100/(64*i)
}
}
//===========================[ PORTS ]===================================================*
void Port_Init(void)
{
//CAUTION:Follow the configuration order for setting the ports.
// 1) setting value(GPnDAT)
// 2) setting control register (GPnCON)
// 3) configure pull-up resistor(GPnUP)
//32bit data bus configuration
//=== PORT A GROUP
//Ports : GPA22 GPA21 GPA20 GPA19 GPA18 GPA17 GPA16 GPA15 GPA14 GPA13 GPA12
//Signal : nFCE nRSTOUT nFRE nFWE ALE CLE nGCS5 nGCS4 nGCS3 nGCS2 nGCS1
//Binary : 1 1 1 , 1 1 1 1 , 1 1 1 1
//Ports : GPA11 GPA10 GPA9 GPA8 GPA7 GPA6 GPA5 GPA4 GPA3 GPA2 GPA1 GPA0
//Signal : ADDR26 ADDR25 ADDR24 ADDR23 ADDR22 ADDR21 ADDR20 ADDR19 ADDR18 ADDR17 ADDR16 ADDR0
//Binary : 1 1 1 1 , 1 1 1 1 , 1 1 1 1
rGPACON = 0x7fffff;
//===* PORT B GROUP
//Ports : GPB10 GPB9 GPB8 GPB7 GPB6 GPB5 GPB4 GPB3 GPB2 GPB1 GPB0
//Signal : nXDREQ0 nXDACK0 nXDREQ1 nXDACK1 nSS_KBD nDIS_OFF L3CLOCK L3DATA L3MODE nIrDATXDEN Keyboard
//Setting: INPUT OUTPUT INPUT OUTPUT INPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT
//Binary : 00 , 01 00 , 01 00 , 01 01 , 01 01 , 01 01
rGPBCON = 0x044555;
rGPBUP = 0x7ff; // The pull up function is disabled GPB[10:0]
//=== PORT C GROUP
//Ports : GPC15 GPC14 GPC13 GPC12 GPC11 GPC10 GPC9 GPC8 GPC7 GPC6 GPC5 GPC4 GPC3 GPC2 GPC1 GPC0
//Signal : VD7 VD6 VD5 VD4 VD3 VD2 VD1 VD0 LCDVF2 LCDVF1 LCDVF0 VM VFRAME VLINE VCLK LEND
//Binary : 10 10 , 10 10 , 10 10 , 10 10 , 10 10 , 10 10 , 10 10 , 10 10
rGPCCON = 0xaaaaaaaa;
rGPCUP = 0xffff; // The pull up function is disabled GPC[15:0]
//=== PORT D GROUP
//Ports : GPD15 GPD14 GPD13 GPD12 GPD11 GPD10 GPD9 GPD8 GPD7 GPD6 GPD5 GPD4 GPD3 GPD2 GPD1 GPD0
//Signal : VD23 VD22 VD21 VD20 VD19 VD18 VD17 VD16 VD15 VD14 VD13 VD12 VD11 VD10 VD9 VD8
//Binary : 10 10 , 10 10 , 10 10 , 10 10 , 10 10 , 10 10 , 10 10 ,10 10
rGPDCON = 0xaaaaaaaa;
rGPDUP = 0xffff; // The pull up function is disabled GPD[15:0]
//=== PORT E GROUP
//Ports : GPE15 GPE14 GPE13 GPE12 GPE11 GPE10 GPE9 GPE8 GPE7 GPE6 GPE5 GPE4
//Signal : IICSDA IICSCL SPICLK SPIMOSI SPIMISO SDDATA3 SDDATA2 SDDATA1 SDDATA0 SDCMD SDCLK I2SSDO
//Binary : 10 10 , 10 10 , 10 10 , 10 10 , 10 10 , 10 10 ,
//-------------------------------------------------------------------------------------------------------
//Ports : GPE3 GPE2 GPE1 GPE0
//Signal : I2SSDI CDCLK I2SSCLK I2SLRCK
//Binary : 10 10 , 10 10
rGPECON = 0xaaaaaaaa;
rGPEUP = 0xffff; // The pull up function is disabled GPE[15:0]
//=== PORT F GROUP
//Ports : GPF7 GPF6 GPF5 GPF4 GPF3 GPF2 GPF1 GPF0
//Signal : nLED_8 nLED_4 nLED_2 nLED_1 nIRQ_PCMCIA EINT2 KBDINT EINT0
//Setting: Output Output Output Output EINT3 EINT2 EINT1 EINT0
//Binary : 01 01 , 01 01 , 10 10 , 10 10
rGPFCON = 0x55aa;
rGPFUP = 0xff; // The pull up function is disabled GPF[7:0]
//=== PORT G GROUP
//Ports : GPG15 GPG14 GPG13 GPG12 GPG11 GPG10 GPG9 GPG8 GPG7 GPG6
//Signal : nYPON YMON nXPON XMON EINT19 DMAMODE1 DMAMODE0 DMASTART KBDSPICLK KBDSPIMOSI
//Setting: nYPON YMON nXPON XMON EINT19 Output Output Output SPICLK1 SPIMOSI1
//Binary : 11 11 , 11 11 , 10 01 , 01 01 , 11 11
//-----------------------------------------------------------------------------------------
//Ports : GPG5 GPG4 GPG3 GPG2 GPG1 GPG0
//Signal : KBDSPIMISO LCD_PWREN EINT11 nSS_SPI IRQ_LAN IRQ_PCMCIA
//Setting: SPIMISO1 LCD_PWRDN EINT11 nSS0 EINT9 EINT8
//Binary : 11 11 , 10 11 , 10 10
rGPGCON = 0xff95ffba;
rGPGUP = 0xffff; // The pull up function is disabled GPG[15:0]
/*
//GPG4 Output Port [9:8] 01 -> LCD_PWREN Enable
rGPGCON = (rGPGCON & 0xfffffcff) | (1<<8);
rGPGDAT = (rGPGDAT & 0xffef) | (1<<4);
*/
//=== PORT H GROUP
//Ports : GPH10 GPH9 GPH8 GPH7 GPH6 GPH5 GPH4 GPH3 GPH2 GPH1 GPH0
//Signal : CLKOUT1 CLKOUT0 UCLK nCTS1 nRTS1 RXD1 TXD1 RXD0 TXD0 nRTS0 nCTS0
//Binary : 10 , 10 10 , 11 11 , 10 10 , 10 10 , 10 10
rGPHCON = 0x2afaaa;
rGPHUP = 0x7ff; // The pull up function is disabled GPH[10:0]
//External interrupt will be falling edge triggered.
rEXTINT0 = 0x22222222; // EINT[7:0]
rEXTINT1 = 0x22222222; // EINT[15:8]
rEXTINT2 = 0x22222222; // EINT[23:16]
}
//===========================[ UART ]==============================
static int whichUart=0;
void Uart_Init(int pclk,int baud)
{
int i;
if(pclk == 0)
pclk = PCLK;
rUFCON0 = 0x0; //UART channel 0 FIFO control register, FIFO disable
rUFCON1 = 0x0; //UART channel 1 FIFO control register, FIFO disable
rUFCON2 = 0x0; //UART channel 2 FIFO control register, FIFO disable
rUMCON0 = 0x0; //UART chaneel 0 MODEM control register, AFC disable
rUMCON1 = 0x0; //UART chaneel 1 MODEM control register, AFC disable
//UART0
rULCON0 = 0x3; //Line control register : Normal,No parity,1 stop,8 bits
// [10] [9] [8] [7] [6] [5] [4] [3:2] [1:0]
// Clock Sel, Tx Int, Rx Int, Rx Time Out, Rx err, Loop-back, Send break, Transmit Mode, Receive Mode
// 0 1 0 , 0 1 0 0 , 01 01
// PCLK Level Pulse Disable Generate Normal Normal Interrupt or Polling
rUCON0 = 0x245; // Control register
// rUBRDIV0=( (int)(pclk/16./baud) -1 ); //Baud rate divisior register 0
rUBRDIV0=( (int)(pclk/16./baud+0.5) -1 ); //Baud rate divisior register 0
//UART1
rULCON1 = 0x3;
rUCON1 = 0x245;
rUBRDIV1=( (int)(pclk/16./baud) -1 );
//UART2
rULCON2 = 0x3;
rUCON2 = 0x245;
rUBRDIV2=( (int)(pclk/16./baud) -1 );
for(i=0;i<100;i++);
}
//===================================================================
void Uart_Select(int ch)
{
whichUart = ch;
}
//===================================================================
void Uart_TxEmpty(int ch)
{
if(ch==0)
while(!(rUTRSTAT0 & 0x4)); //Wait until tx shifter is empty.
else if(ch==1)
while(!(rUTRSTAT1 & 0x4)); //Wait until tx shifter is empty.
else if(ch==2)
while(!(rUTRSTAT2 & 0x4)); //Wait until tx shifter is empty.
}
//=====================================================================
char Uart_Getch(void)
{
if(whichUart==0)
{
while(!(rUTRSTAT0 & 0x1)); //Receive data ready
}
else if(whichUart==1)
{
while(!(rUTRSTAT1 & 0x1)); //Receive data ready
return RdURXH1();
}
else if(whichUart==2)
{
while(!(rUTRSTAT2 & 0x1)); //Receive data ready
return RdURXH2();
}
}
//====================================================================
char Uart_GetKey(void)
{
if(whichUart==0)
{
if(rUTRSTAT0 & 0x1) //Receive data ready
return RdURXH0();
else
return 0;
}
else if(whichUart==1)
{
if(rUTRSTAT1 & 0x1) //Receive data ready
return RdURXH1();
else
return 0;
}
else if(whichUart==2)
{
if(rUTRSTAT2 & 0x1) //Receive data ready
return RdURXH2();
else
return 0;
}
}
//====================================================================
void Uart_GetString(char *string)
{
char *string2 = string;
char c;
while((c = Uart_Getch())!='\r')
{
if(c=='\b')
{
if( (int)string2 < (int)string )
{
Uart_Printf("\b \b");
string--;
}
}
else
{
*string++ = c;
Uart_SendByte(c);
}
}
*string='\0';
Uart_SendByte('\n');
}
//=====================================================================
int Uart_GetIntNum(void)
{
char str[30];
char *string = str;
int base = 10;
int minus = 0;
int result = 0;
int lastIndex;
int i;
Uart_GetString(string);
if(string[0]=='-')
{
minus = 1;
string++;
}
if(string[0]=='0' && (string[1]=='x' || string[1]=='X'))
{
base = 16;
string += 2;
}
// lastIndex = strlen(string) - 1;
lastIndex = strlen(string) ;
if(lastIndex<0)
return -1;
if(string[lastIndex]=='h' || string[lastIndex]=='H' )
{
base = 16;
string[lastIndex] = 0;
lastIndex--;
}
if(base==10)
{
result = atoi(string);
result = minus ? (-1*result):result;
}
else
{
for(i=0;i<=lastIndex;i++)
{
if(isalpha(string[i]))
{
if(isupper(string[i]))
result = (result<<4) + string[i] - 'A' + 10;
else
result = (result<<4) + string[i] - 'a' + 10;
}
else
result = (result<<4) + string[i] - '0';
}
result = minus ? (-1*result):result;
}
return result;
}
//=====================================================================
void Uart_SendByte(int data)
{
if(whichUart==0)
{
if(data=='\n')
{
while(!(rUTRSTAT0 & 0x2));
Delay(10); //because the slow response of hyper_terminal
WrUTXH0('\r');
}
while(!(rUTRSTAT0 & 0x2)); //Wait until THR is empty.
Delay(10);
WrUTXH0(data);
}
else if(whichUart==1)
{
if(data=='\n')
{
while(!(rUTRSTAT1 & 0x2));
Delay(10); //because the slow response of hyper_terminal
rUTXH1 = '\r';
}
while(!(rUTRSTAT1 & 0x2)); //Wait until THR is empty.
Delay(10);
rUTXH1 = data;
}
else if(whichUart==2)
{
if(data=='\n')
{
while(!(rUTRSTAT2 & 0x2));
Delay(10); //because the slow response of hyper_terminal
rUTXH2 = '\r';
}
while(!(rUTRSTAT2 & 0x2)); //Wait until THR is empty.
Delay(10);
rUTXH2 = data;
}
}
//====================================================================
void Uart_SendString(char *pt)
{
while(*pt)
Uart_SendByte(*pt++);
}
//=====================================================================
//If you don't use vsprintf(), the code size is reduced very much.
void Uart_Printf(char *fmt,...)
{
va_list ap;
char string[256];
va_start(ap,fmt);
vsprintf(string,fmt,ap);
Uart_SendString(string);
va_end(ap);
}
//========================*[ Timer ]==============================**
void Timer_Start(int divider) //0:16us,1:32us 2:64us 3:128us
{
rWTCON = ((PCLK/1000000-1)<<8)|(divider<<3); //Watch-dog timer control register
rWTDAT = 0xffff; //Watch-dog timer data register
rWTCNT = 0xffff; //Watch-dog count register
//Watch-dog timer enable & interrupt disable
// rWTCON = rWTCON |(1<<5) & !(1<<2); //?
rWTCON = rWTCON | (1<<5) | ~(1<<2); //May 06, 2002 SOP
}
//=================================================================
int Timer_Stop(void)
{
rWTCON = ((PCLK/1000000-1)<<8);
return (0xffff - rWTCNT);
}
//========================*[ MPLL ]==============================*
void ChangeMPllValue(int mdiv,int pdiv,int sdiv)
{
rMPLLCON = (mdiv<<12) | (pdiv<<4) | sdiv;
}
//========================[ HCLK, PCLK ]===========================
void ChangeClockDivider(int hdivn,int pdivn)
{
// hdivn,pdivn FCLK:HCLK:PCLK
// 0,0 1:1:1
// 0,1 1:1:2
// 1,0 1:2:2
// 1,1 1:2:4
rCLKDIVN = (hdivn<<1) | pdivn;
if(hdivn)
MMU_SetAsyncBusMode();
else
MMU_SetFastBusMode();
}
void ChangeUPllValue(int mdiv,int pdiv,int sdiv)
{
rUPLLCON = (mdiv<<12) | (pdiv<<4) | sdiv;
}
//========================*[ General Library ]=====================*
void * malloc(unsigned nbyte)
//Very simple; Use malloc() & free() like Stack
//void *mallocPt=Image$$RW$$Limit;
{
void *returnPt = mallocPt;
mallocPt = (int *)mallocPt+nbyte/4+((nbyte%4)>0); //To align 4byte
if( (int)mallocPt > HEAPEND )
{
mallocPt = returnPt;
return NULL;
}
return returnPt;
}
//-------------------------------------------------------------------
void free(void *pt)
{
mallocPt = pt;
}
?? 快捷鍵說明
復制代碼
Ctrl + C
搜索代碼
Ctrl + F
全屏模式
F11
切換主題
Ctrl + Shift + D
顯示快捷鍵
?
增大字號
Ctrl + =
減小字號
Ctrl + -