/*     cx24110 - Single Chip Satellite Channel Receiver driver module               used on the the Pinnacle PCTV Sat cards    Copyright (C) 2002 Peter Hettkamp <peter.hettkamp@t-online.de> based on    work    Copyright (C) 1999 Convergence Integrated Media GmbH <ralph@convergence.de>    This program is free software; you can redistribute it and/or modify    it under the terms of the GNU General Public License as published by    the Free Software Foundation; either version 2 of the License, or    (at your option) any later version.    This program is distributed in the hope that it will be useful,    but WITHOUT ANY WARRANTY; without even the implied warranty of    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the    GNU General Public License for more details.    You should have received a copy of the GNU General Public License    along with this program; if not, write to the Free Software    Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.*/    /* currently drives the Conexant cx24110 and cx24106 QPSK decoder chips,    connected via i2c to a Conexant Fusion 878 (this uses the standard   linux bttv driver). The tuner chip is supposed to be the Conexant   cx24108 digital satellite tuner, driven through the tuner interface   of the cx24110. SEC is also supplied by the cx24110.      Oct-2002: Migrate to API V3 (formerly known as NEWSTRUCT)*/#include <linux/module.h>#include <linux/init.h>#include "compat.h"#include "dvb_frontend.h"static int debug = 0;#define dprintk	if (debug) printkstaticstruct dvb_frontend_info cx24110_info = {	name: "Conexant CX24110 with CX24108 tuner, aka HM1221/HM1811",	type: FE_QPSK,	frequency_min: 950000,	frequency_max: 2150000,	frequency_stepsize: 1011,           /* kHz for QPSK frontends, can be reduced to 253kHz on the cx24108 tuner */	frequency_tolerance: 29500,	symbol_rate_min: 1000000,	symbol_rate_max: 45000000,/*      symbol_rate_tolerance: ???,*/	notifier_delay: 50,                /* 1/20 s */	caps:   FE_CAN_INVERSION_AUTO |		FE_CAN_FEC_1_2 | FE_CAN_FEC_2_3 | FE_CAN_FEC_3_4 |		FE_CAN_FEC_5_6 | FE_CAN_FEC_7_8 | FE_CAN_FEC_AUTO |		FE_CAN_QPSK | 		FE_CAN_CLEAN_SETUP};/* fixme: are these values correct? especially ..._tolerance and caps */staticstruct {u8 reg; u8 data;} cx24110_regdata[]=                      /* Comments beginning with @ denote this value should                         be the default */        {{0x09,0x01}, /* SoftResetAll */         {0x09,0x00}, /* release reset */         {0x01,0xe8}, /* MSB of code rate 27.5MS/s */         {0x02,0x17}, /* middle byte " */         {0x03,0x29}, /* LSB         " */         {0x05,0x03}, /* @ DVB mode, standard code rate 3/4 */         {0x06,0xa5}, /* @ PLL 60MHz */         {0x07,0x01}, /* @ Fclk, i.e. sampling clock, 60MHz */         {0x0a,0x00}, /* @ partial chip disables, do not set */         {0x0b,0x01}, /* set output clock in gapped mode, start signal low                         active for first byte */         {0x0c,0x11}, /* no parity bytes, large hold time, serial data out */         {0x0d,0x6f}, /* @ RS Sync/Unsync thresholds */         {0x10,0x40}, /* chip doc is misleading here: write bit 6 as 1                         to avoid starting the BER counter. Reset the                          CRC test bit. Finite counting selected */         {0x15,0xff}, /* @ size of the limited time window for RS BER                         estimation. It is <value>*256 RS blocks, this                         gives approx. 2.6 sec at 27.5MS/s, rate 3/4 */         {0x16,0x00}, /* @ enable all RS output ports */         {0x17,0x04}, /* @ time window allowed for the RS to sync */         {0x18,0xae}, /* @ allow all standard DVB code rates to be scanned                         for automatically */                      /* leave the current code rate and normalization                         registers as they are after reset... */         {0x21,0x10}, /* @ during AutoAcq, search each viterbi setting                         only once */         {0x23,0x18}, /* @ size of the limited time window for Viterbi BER                               estimation. It is <value>*65536 channel bits, i.e.                         approx. 38ms at 27.5MS/s, rate 3/4 */         {0x24,0x24}, /* do not trigger Viterbi CRC test. Finite count window */                      /* leave front-end AGC parameters at default values */                      /* leave decimation AGC parameters at default values */         {0x35,0x40}, /* disable all interrupts. They are not connected anyway */         {0x36,0xff}, /* clear all interrupt pending flags */         {0x37,0x00}, /* @ fully enable AutoAcqq state machine */         {0x38,0x07}, /* @ enable fade recovery, but not autostart AutoAcq */                      /* leave the equalizer parameters on their default values */                      /* leave the final AGC parameters on their default values */         {0x41,0x00}, /* @ MSB of front-end derotator frequency */         {0x42,0x00}, /* @ middle bytes " */         {0x43,0x00}, /* @ LSB          " */                      /* leave the carrier tracking loop parameters on default */                      /* leave the bit timing loop parameters at gefault */         {0x56,0x4d}, /* set the filtune voltage to 2.7V, as recommended by */                      /* the cx24108 data sheet for symbol rates above 15MS/s */         {0x57,0x00}, /* @ Filter sigma delta enabled, positive */         {0x61,0x95}, /* GPIO pins 1-4 have special function */         {0x62,0x05}, /* GPIO pin 5 has special function, pin 6 is GPIO */         {0x63,0x00}, /* All GPIO pins use CMOS output characteristics */         {0x64,0x20}, /* GPIO 6 is input, all others are outputs */         {0x6d,0x30}, /* tuner auto mode clock freq 62kHz */         {0x70,0x15}, /* use auto mode, tuner word is 21 bits long */         {0x73,0x00}, /* @ disable several demod bypasses */         {0x74,0x00}, /* @  " */         {0x75,0x00}  /* @  " */                      /* the remaining registers are for SEC */	};staticint cx24110_writereg (struct dvb_i2c_bus *i2c, int reg, int data){        u8 buf [] = { reg, data };	struct i2c_msg msg = { addr: 0x55, flags: 0, buf: buf, len: 2 };/* fixme (medium): HW allows any i2c address. 0x55 is the default, but the   cx24110 might show up at any address */ 	int err;        if ((err = i2c->xfer (i2c, &msg, 1)) != 1) {		dprintk ("%s: writereg error (err == %i, reg == 0x%02x, data == 0x%02x)\n", __FUNCTION__, err, reg, data);		return -EREMOTEIO;	}        return 0;}staticu8 cx24110_readreg (struct dvb_i2c_bus *i2c, u8 reg){	int ret;	u8 b0 [] = { reg };	u8 b1 [] = { 0 };	struct i2c_msg msg [] = { { addr: 0x55, flags: 0, buf: b0, len: 1 },			   { addr: 0x55, flags: I2C_M_RD, buf: b1, len: 1 } };/* fixme (medium): address might be different from 0x55 */	ret = i2c->xfer (i2c, msg, 2);	if (ret != 2)		dprintk("%s: readreg error (ret == %i)\n", __FUNCTION__, ret);	return b1[0];}staticint cx24108_write (struct dvb_i2c_bus *i2c, u32 data){/* tuner data is 21 bits long, must be left-aligned in data *//* tuner cx24108 is written through a dedicated 3wire interface on the demod chip *//* fixme (low): add error handling, avoid infinite loops if HW fails... */dprintk("cx24110 debug: cx24108_write(%8.8x)\n",data);        cx24110_writereg(i2c,0x6d,0x30); /* auto mode at 62kHz */        cx24110_writereg(i2c,0x70,0x15); /* auto mode 21 bits */        /* if the auto tuner writer is still busy, clear it out */        while(cx24110_readreg(i2c,0x6d)&0x80) cx24110_writereg(i2c,0x72,0);        /* write the topmost 8 bits */        cx24110_writereg(i2c,0x72,(data>>24)&0xff);        /* wait for the send to be completed */        while((cx24110_readreg(i2c,0x6d)&0xc0)==0x80);        /* send another 8 bytes */        cx24110_writereg(i2c,0x72,(data>>16)&0xff);        while((cx24110_readreg(i2c,0x6d)&0xc0)==0x80);        /* and the topmost 5 bits of this byte */        cx24110_writereg(i2c,0x72,(data>>8)&0xff);        while((cx24110_readreg(i2c,0x6d)&0xc0)==0x80);        /* now strobe the enable line once */        cx24110_writereg(i2c,0x6d,0x32);        cx24110_writereg(i2c,0x6d,0x30);                return 0;}staticint cx24108_set_tv_freq (struct dvb_i2c_bus *i2c, u32 freq){/* fixme (low): error handling */        int i, a, n, pump;         u32 band, pll;                static const u32 osci[]={ 950000,1019000,1075000,1178000,			         1296000,1432000,1576000,1718000,				 1856000,2036000,2150000};        static const u32 bandsel[]={0,0x00020000,0x00040000,0x00100800,				      0x00101000,0x00102000,0x00104000,				      0x00108000,0x00110000,0x00120000,				      0x00140000};                   #define XTAL 1011100 /* Hz, really 1.0111 MHz and a /10 prescaler */        dprintk("cx24110 debug: cx24108_set_tv_freq, freq=%d\n",freq);                freq/=1000; /* change units to kHz */        if(freq<950000) freq=950000; /* kHz */        if(freq>2150000) freq=2150000; /* satellite IF is 950..2150MHz */        /* decide which VCO to use for the input frequency */        for(i=1;(i<sizeof(osci)/sizeof(osci[0]))&&(osci[i]<freq);i++);        dprintk("cx24110 debug: select vco #%d (f=%d)\n",i,freq);        band=bandsel[i];        /* the gain values must be set by SetSymbolrate */        /* compute the pll divider needed, from Conexant data sheet,           resolved for (n*32+a), remember f(vco) is f(receive) *2 or *4,           depending on the divider bit. It is set to /4 on the 2 lowest            bands  */        n=((i<=2?2:1)*freq*10L)/(XTAL/100);        a=n%32; n/=32; if(a==0) n--;        pump=(freq<(osci[i-1]+osci[i])/2);        pll=0xf8000000|            ((pump?1:2)<<(14+11))|            ((n&0x1ff)<<(5+11))|            ((a&0x1f)<<11);        /* everything is shifted left 11 bits to left-align the bits in the           32bit word. Output to the tuner goes MSB-aligned, after all */        dprintk("cx24110 debug: pump=%d, n=%d, a=%d\n",pump,n,a);        cx24108_write(i2c,band);        /* set vga and vca to their widest-band settings, as a precaution.           SetSymbolrate might not be called to set this up */        cx24108_write(i2c,0x500c0000);        cx24108_write(i2c,0x83f1f800);        cx24108_write(i2c,pll);        cx24110_writereg(i2c,0x56,0x7f);/* fixme (low): tuner pll lock can be monitored on GPIO pin 4 of cx24110 */        return 0;}staticint cx24110_init (struct dvb_i2c_bus *i2c){/* fixme (low): error handling */        int i;        	dprintk("%s: init chip\n", __FUNCTION__);        for(i=0;i<sizeof(cx24110_regdata)/sizeof(cx24110_regdata[0]);i++) {           cx24110_writereg(i2c,cx24110_regdata[i].reg,cx24110_regdata[i].data);        };	return 0;}staticint cx24110_set_inversion (struct dvb_i2c_bus *i2c, fe_spectral_inversion_t inversion){/* fixme (low): error handling */	switch (inversion) {	case INVERSION_OFF:                cx24110_writereg(i2c,0x37,cx24110_readreg(i2c,0x37)|0x1);                /* AcqSpectrInvDis on. No idea why someone should want this */                cx24110_writereg(i2c,0x5,cx24110_readreg(i2c,0x5)&0xf7);                /* Initial value 0 at start of acq */                cx24110_writereg(i2c,0x22,cx24110_readreg(i2c,0x22)&0xef);                /* current value 0 */                /* The cx24110 manual tells us this reg is read-only.                   But what the heck... set it ayways */                break;	case INVERSION_ON:                cx24110_writereg(i2c,0x37,cx24110_readreg(i2c,0x37)|0x1);                /* AcqSpectrInvDis on. No idea why someone should want this */                cx24110_writereg(i2c,0x5,cx24110_readreg(i2c,0x5)|0x08);                /* Initial value 1 at start of acq */                cx24110_writereg(i2c,0x22,cx24110_readreg(i2c,0x22)|0x10);                /* current value 1 */                break;	case INVERSION_AUTO:                cx24110_writereg(i2c,0x37,cx24110_readreg(i2c,0x37)&0xfe);                /* AcqSpectrInvDis off. Leave initial & current states as is */                break;	default:		return -EINVAL;	}	return 0;}staticint cx24110_set_fec (struct dvb_i2c_bus *i2c, fe_code_rate_t fec){/* fixme (low): error handling */        static const int rate[]={-1,1,2,3,5,7,-1};        static const int g1[]={-1,0x01,0x02,0x05,0x15,0x45,-1};        static const int g2[]={-1,0x01,0x03,0x06,0x1a,0x7a,-1};        /* Well, the AutoAcq engine of the cx24106 and 24110 automatically           searches all enabled viterbi rates, and can handle non-standard           rates as well. */                        if (fec>FEC_AUTO)                 fec=FEC_AUTO;        if(fec==FEC_AUTO) { /* (re-)establish AutoAcq behaviour */           cx24110_writereg(i2c,0x37,cx24110_readreg(i2c,0x37)&0xdf);           /* clear AcqVitDis bit */           cx24110_writereg(i2c,0x18,0xae);           /* allow all DVB standard code rates */           cx24110_writereg(i2c,0x05,(cx24110_readreg(i2c,0x05)&0xf0)|0x3);           /* set nominal Viterbi rate 3/4 */           cx24110_writereg(i2c,0x22,(cx24110_readreg(i2c,0x22)&0xf0)|0x3);           /* set current Viterbi rate 3/4 */           cx24110_writereg(i2c,0x1a,0x05); cx24110_writereg(i2c,0x1b,0x06);           /* set the puncture registers for code rate 3/4 */           return 0;        } else {           cx24110_writereg(i2c,0x37,cx24110_readreg(i2c,0x37)|0x20);