======================================================================Changes for U-Boot 1.1.5:======================================================================* Cleanup compile warnings. Prepare for release 1.1.5* Fix compile problem in include/configs/ep82xxm.h  (must have never been tested before!)* MCC200: Fix uninitialized variable problem in LCD driver* Add board/cpu specific NAND chip select function to 440 NDFC  Based on idea and implementation from Jeff Mann  Patch by Stefan Roese, 20 Oct 2006* Make 4xx bootup message shorter on 440EPx/GRx platforms  Patch by Stefan Roese, 18 Oct 2006* Add (preliminary) support for V38B board* PPC405EP: Add support for board configuration of CPC0_PCI register  This is needed to be able to configure PerWE*/PCI_INT* pin as PerWE*  Patch by Tolunay Orkun, 07 Apr 2006* PPC405EP: Add CFG_GPIO0_OR, CFG_GPIO0_ODR to setup GPIO completely.  - Add configuration of Open Drain GPIO Output selection  - Add configuration of initial value of GPIO output pins  Patch by Tolunay Orkun, 07 Apr 2006* Fix spelling; minor code cleanup.* Fix JFFS2 compilation problem  Patch by Stefan Roese, 12 Oct 2006* Cleanup of NAND update patch (remove changelog from cmd_nand.c)  Patch by Guido Classen, 10 Oct 2006* Several improvements to the new NAND subsystem:  - JFFS2 related commands implemented in mtd-utils style  - Support for bad blocks  - Bad block testing commands  - NAND lock commands  Please take a look at doc/README.nand for more details  Patch by Guido Classen, 10 Oct 2006* Define IH_CPU_AVR32  Make it possible to generate AVR32 uImage files with mkimage and  make cmd_bootm recognize them.  Patch by Haavard Skinnemoen, 22 Sep 2006* Fix buffer overflow problem in ft_build.c  Patch by Fredrik Roubert, 09 Oct 2006* Make bootp implementation RFC3046 compliant  Patch by Joakim Larsson, 27 Jun 2006* TQM5200: perform POST memory test only on STK52xx carrier board.  (and then only if PSC6_3 is read as "1" when booting).  Patch by Martin Krause, 21 Jun 2006* Move "ar" flags to config.mk to allow for silent "make -s"  Based on patch by Mike Frysinger, 20 Jun 2006* Coding style cleanup* Add support for EP82xxM boards  Patch by Aaron Sells, 20 Jun 2006* Fix comments in include/ppc440.h  Patch by Martin Hicks, 16 Jun 2006* Update for CAM5200 board:  - Map in a additional chip selects CS4 and CS5.  - Modify the port configration, configure six UARTs and no PCI,    ATA and USB.  - Add custom flash driver to handle specific byte swapping* Fix TLB setup for Ocotea board  Patch by Stefan Roese, 30 Sep 2006* Fix reset problem in sequoia sdram init code  Patch by Stefan Roese, 23 Sep 2006* Disable autoboot abort for FO300 when silent mode is enabled  (according to S1 switch setting).* Cleanup examples binaries* Add support for AMCC Rainier PPX440GRx eval board  Patch by Stefan Roese, 13 Sep 2006* Add NAND environment support for PPC440EPx Sequoia NAND boot config  Patch by Stefan Roese, 12 Sep 2006* Update NAND boot documentation  Patch by Stefan Roese, 12 Sep 2006* Fix alignment problem in "mtdparts" command* Add documentation on the latest build environment extensions to  the README file.* Remove dead code (i2o and dma) from cpu/mpc824x/drivers/ directory.* Fix LOG_DIR directory creation error.  Add support for automatic creation of BUILD_DIR directory.* Fix build problem cpu/ppc4xx/ndfc.c  Patch by Stefan Roese, 07 Sep 2006* Fix build problem with CPCI440  Patch by Stefan Roese, 07 Sep 2006* Change Yellowstone to use CFI write buffer  Patch by Stefan Roese, 07 Sep 2006* Add support for AMCC Sequoia PPC440EPx eval board  - Add support for PPC440EPx & PPC440GRx  - Add support for PPC440EP(x)/GR(x) NAND controller    in cpu/ppc4xx directory  - Add NAND boot functionality for Sequoia board,    please see doc/README.nand-boot-ppc440 for details  - This Sequoia NAND image doesn't support environment    in NAND for now. This will be added in a short while.  Patch by Stefan Roese, 07 Sep 2006* Fix mkimage -l bug with multifile images on 64bit platforms  Patch by David Updegraff, 06 Sep 2006* Fix build problems on sorcery board.* Fix coldfire build problems.  Patch by Marian Balakowicz, 01 Sep 2006* Add support for a saving build objects in a separate directory.  Modifications are based on the Linux kernel approach and support  two use cases:  1) Add O= to the make command line 'make O=/tmp/build all'  2) Set environement variable BUILD_DIR to point to the desired location	'export BUILD_DIR=/tmp/build'	'make'  The second approach can also be used with a MAKEALL script	'export BUILD_DIR=/tmp/build'	'./MAKEALL'  Command line 'O=' setting overrides the BUILD_DIR environent variable.  When none of the above methods is used the local build is performed  and the object files are placed in the source directory.* Remove the board/netstar/crcit binary from git repository.* Fix tools/updater build error.* Fix tools/easylogo build error.* Fixed problems on PRS200 board caused by adding splash screen on MCC200* Extended README entry on coding style* Added another example showing simple interrupt interception.* Added simple_strtoul(), getenv() and setenv() to the exported functions.  Also bumped up ABI version to reflect this change.* Added interrupt handling capabilities for mpc5xxx processors.  Also added Linux like BUG() macros.* Coding Style cleanup.  Patch by Stefano Babic, 31 Aug 2006* Add splashscreen support for MCC200 board.* Make the serial driver framework work with CONFIG_SERIAL_MULTI  enabled* PCIe endpoint support for AMCC Yucca 440SPe board  Patch by Tirumala R Marri, 26 Aug 2006* Improve DIMM detection for AMCC Yucca 440SPe board  Improved the memory DIMM detection for the Yucca 440SPe board for  the case where a memory DIMM is falsely detected as present.  This issue is seen on some AMCC Yucca 440SPe validation boards if  only one 512MB memory DIMM is installed, i.e. DIMM slot 0 is  populated and DIMM slot 1 is empty.  In this case, U-Boot does  not correctly detect that there is only one DIMM memory module  installed and will falsely detect two DIMM memory modules are  present and therefore U-Boot will not calculate the correct amount  of total memory and u-boot will not booting up.  Patch by Adam Graham, 24 Aug 2006* Fix typo.* Code cleanup* Update for MCC200 / PRS200 boards:  - auto-adjust console device for Linux.  - fix typos.* Add a fix for a buggy USB device on the FO300 board.* Updates for MCC200 / PRS200 boards:  - support for configurations with SDRAM or DDR memory,  - support for highboot and lowboot  - adjusting environment definitions* Add support for WTK FO300 board (TQM5200 based).* Fix TQM834x hang.* Update for SC520 board.  Patch by David Updegraff, 02 Dec 2005* Fixed common.h spelling error.  Patch by Cory Tusar, 30 Nov 2005* Fix typo.  Patch by Andreas Engel, 28 Nov 2005* Fix fatload command on FAT32 formatted partitions.  Patch by Joachim Jaeger, 18 Nov 2005* Fix drivers/dm9000.c when configured in 32 bit mode.  Patch by Eric Benard, 17 Nov 2005* Cleanup debug code for yucca board.* MCC200: restrict addressable flash space to 32 MB* Add debug console on COM12 for MCC200 board* Fix control-c handing in CONFIG_CMDLINE_EDITING  Properly pass break code back from readline.  Patch by Roger Blofeld, 31 Jul 2006* Add commandline history support to all AMCC eval boards  Patch by Stefan Roese, 07 Aug 2006* Add Macronix MXLV320T flash support for AMCC Bamboo  Patch by Stefan Roese, 07 Aug 2006* Change "mii info" to not print an error upon missing PHY at address  Patch by Stefan Roese, 07 Aug 2006* Fix PCI-Express on PPC440SPe rev. A.* Fix preboot message on TQM85xx after switching to hush parser.* Adapt TQM85xx ramdisk address to Linux kernel memory map* Add initial support for PCI-Express on PPC440SPe (Yucca board).* Fix compiler warning for TRAB board.  Patch by Martin Krause, 07 Aug 2006* Prevent USB commands from working when USB is stopped.* Add rudimentary handling of alternate settings of USB interfaces.  This is in order to fix issues with some USB sticks timing out  during initialization. Some code readability improvements.* PPC440 DDR setup: Set SDRAM0_CFG0[PMU]=0 for best performance  AMCC suggested to set the PMU bit to 0 for best performace on  the PPC440 DDR controller.  Please see doc/README.440-DDR-performance for details.  Patch by Stefan Roese, 28 Jul 2006* AMCC bamboo (440EP) U-Boot image reduced to 384kbyte  Please see doc/README.bamboo for details.  Patch by Stefan Roese, 27 Jul 2006* Fix CONFIG_CMDLINE_EDITING implementation  Patch by Stefan Roese, 27 Jul 2006* Fix preboot message on TQM5200 after switching to hush parser.* MCC200: set default configuration to low_boot DDR,  and support for configurable options high_boot and/or SDRAM.* Add support for 256 MB SDRAM on CPU87  Patch by Josef Wagner, 25 Nov 2005* Add configuration for cam5200 board (based on TQM5200S).* More code cleanup* Disabled kvme080 board in MAKEALL because of build problems.* Code cleanup* Update NetStar board  Patch by Ladislav Michl, 03 Nov 2005* Make code better readable.  Patch by Ladislav Michl, 14 Sep 2005* Enable initrd ATAG for xm250 board.  Patch by Josef Wagner, 05 Sep 2005* Add readline cmdline-editing extension  Patch by JinHua Luo, 01 Sep 2005* Add support for friendly-arm SBC-2410X board  Patch by JinHua Luo, 01 Sep 2005* Fix multi-part image support on i386 platform.  Patch by David Updegraff, 19 Aug 2005* Add support for KVME080 board  Patch by Sangmoon Kim, 18 Aug 2005* Fix MIPS LE build problem  Patch by Matej Kupljen, 10 Aug 2005* Check argument count in "mii" command.  Problem pointed out by Andrew Dyer, 13 Jun 2005* Cleanup TQM5200 board configurations:  - make highboot configurations use environment at high end, too,    to avoid flash fragmentation  - always use redundand environment  - don't enable video code for modules without graphics controller  - provide useful (though different) mtdparts settings  - get rid of CONFIG_CS_AUTOCONF which was always set anyway* Extend mkconfig tool to print more useful target name* Add support for high-boot on TQM5200 and TQM5200S boards.  Hint: the CPLD on the TQM5200 must be programmed with a software  version supporting the high boot option! The new TQM5200S is  already supporting this option. On the TQM5200 this option will be  supported in configurations with MPC5200 rev B processors.  To actually "high boot", set jumper X30 on the STK52xx.  Patch by Martin Krause, 12 Jul 2006* Add support for new TQM5200 revisions  - Support for TQM5200S (short version without graphic controller)  - Support for modules with 'N' type S29GL128N Spansion flashes    (requires changes to flash layout)  - Support for MPC5200B cpu (mostly support for second SDRAM bank)  Patch by Martin Krause, 07 Jul 2006* Fix support for PS/2 keyboard on TQM85xx boards  The PS/2 keyobard driver for the TQM85xx modules only supports the  internal DUART of the MPC85xx CPU. Since the MPC8560 doesn't  include a DUART, the TQM8560 modules can't be used with the PS/2  keyboard controller on the STK85xx board.  The PS/2 keyboard driver should work with the modules TQM8540,  TQM8541 and TQM8555, but it only has been tested on a TQM8540, yet.  Make sure the PS/2 controller on the STK85xx is programmed. Jumper  settings: X66 1-2, 9-10; X61 2-3  Patch by Martin Krause, 21 Jun 2006* Adjust RTC century handling on STK52xx board to match Linux driver.  Patch by Martin Krause, 12 Jun 2006* Adjust filenames for USB update images on TRAB board.  During an automatic update via USB stick, U-Boot searches for  images with the name "firmware.img" and "kernel.img". This names  are now changed to "firmw_01.img" and "kernl_01.img". This is done,  to prevent updates of new boards (with the new macronics "c" step  flashes) with old, incompatible firmware or kernel versions.  Patch by Martin Krause, 21 Jun 2006* Bugfix in VFD routine on TRAB board.  Make sure upper lext pixel can be set to blue, too  (so far only red was possible).  Patch by Martin Krause, 15 Feb 2006* Enable buffered flash writes for TB5200 board.* Fix some bugs in TRAB board flash driver.  - increase CFG_FLASH_ERASE_TOUT from 2 to 15 seconds  - use CFG_FLASH_WRITE_TOUT for programming instead of CFG_FLASH_ERASE_TOUT  - remove "Unlock Bypass" mode, because macronix flashes do not support    this mode officially  - fix flash reset command from 0x00FF to 0x00F0. 0x00FF is only specified    for Intel compatible flashes, not for AMD compatible.  Patch by Martin Krause, 15 Feb 2006* Add additional error messages to flash driver on TRAB board  (for erase errors and timeout errors)  Patch by Martin Krause, 14 Feb 2006* Add support for TB5200 board  The TB5200 ("Tinybox") is a small baseboard for the TQM5200 module  integrated in a little aluminium case.  Patch by Martin Krause, 8 Jun 2006