* Enable buffered flash writes for TQM5200 board.* Fix problems with SanDisk Corporation Cruzer Micro USB memory stick.* Add support for TQM885D board.  Patch by Martin Krause, 20 Mar 2006* Fix FEC initialisation: All MII configuration is done via FEC1  registers, but MII_SPEED was configured according to FEC used. So  if only FEC2 was used, this caused the real MII_SPEED register in  FEC1 to stay uninitalised, leqading to "mii_send STUCK!" messages.  Fix: always configure MII_SPEED on FEC1 only.  Patch by Markus Klotzbuecher, 12 Jul 2006* Add support for SPC1920 board.  Patch by Markus Klotzbuecher, 12 Jul 2006* MCC200 board: support console on any one of the Quad UART ports.* Fix error in flash protection calculation on MCC200 board.* Major PCMCIA Cleanup to make code better readable and maintainable.  Notes:  - Board-dependend code for RPXLITE and RPXCLASSIC-based boards    placed to the drivers/rpx_pmcia.c file to avoid duplication.    Same for TQM8xx-based boards (drivers/tqm8xx_pmcia.c).  - drivers/i82365.c has been split into two parts located at    board/atc/ti113x.c and board/cpc45/pd67290.c (ATC and CPC45 are    the only boards using CONFIG_82365).  - Changes were tested for clean build and *very* *few* boards.* Fix timer problems on AMCC yucca board.  Set Timer Clock Select to use CPU clock as a timer input source.* Bring yucca config more in line with other AMCC boards.* Add AMCC bamboo board to MAKEALL build script.* Fix AMCC bamboo eval board compilation errors.* Add system memory to the PCI region list for AMCC PPC44x CPUs.  Enabled it for Yucca board.* Cleanup config file and bootup output for Yucca board.* Fix CONFIG_440_GX define usage.* Remove autogenerated bmp_logo.h file.* Add support for AMCC 440SPe CPU based eval board (Yucca).* Call serial_initialize() before first debug() is used.* Cleanup trab board for GCC-4.x* VoiceBlue update: use new MTD flash partitioning methods, use more  reasonable TEXT_BASE, update default environment and enable keyed  autoboot.  Patch by Ladislav Michl, 16. Aug 2005* Add forgotten changes for the PLEB 2 Board.  Patch by David Snowdon, 13. Aug 2005* Add support for wrPPMC7xx/74xx boards  Patch by Richard Danter, 12 Aug 2005* Add support for gth2 board  Patch by Thomas Lange, Aug 11 2005* Add support for CONFIG_SERIAL_MULTI on MPC5xxx  Patch by Martin Krause, 8 Jun 2006  This patch supports two serial consoles on boards with  a MPC5xxx CPU. The console can be switched at runtime  by setting stdin, stdout and stderr to the desired serial  interface (serial0 or serial1). The PSCs to be used as  console port are definded by CONFIG_PSC_CONSOLE  and CONFIG_PSC_CONSOLE2.  See README.serial_multi for details.* Bugfix in I2C initialisation on S3C2400.  If the bus is blocked because of a previously interrupted  transfer, up to eleven clocks are generated on the I2CSCL  line to complete the transfer and to free the bus.  With this fix pin I2CSCL (PG6) is really configured as GPIO  so the clock pulses are really generated.  Patch by Martin Krause, 04 Apr 2006* Fix DDR6 errata on TQM834x boards  Patch by Thomas Waehner, 07 Mar 2006* Remove obsolete flash driver board/tqm5200/flash.c  Patch by Martin Krause, 11 Jan 2006* Update configuration for CMC-PU2 board  Patch by Martin Krause, 17 Nov 2005* Add support for PS/2 keyboard on TQM85xx board  Patch by Martin Krause, 07 Nov 2005  Tested on a STK85XX baseboard. Make sure the PS/2 controller  has been programmed. Jumper Settings: X66 1-2, 9-10; X61 2-3* Fix TRAB channel switching delay for trab_fkt.bin standalone applikation  In tsc2000_read_channel() the delay after setting the multiplexer  to a temperature channel is increased from 1,5 ms to 10 ms. This  is to allow the multiplexer inputs to stabilize after huge steps  of the input signal level.  Patch by Martin Krause, 08 Nov 2005* Adjust TQM5200 make targets  Make the automatic CS configuration the default.  The dedicated configurations CONFIG_TQM5200_AA, CONFIG_TQM5200_AB  and CONFIG_TQM5200_AC are removed.  "TQM5200_config" is now the default for STK52XX.200 base boards.  On a STK52XX.100 base board "TQM5200_STK100_config" must be used.  Patch by Martin Krause, 07 Nov 2005* Fix setting of environment variable "ver" on trab board  The environment variable "ver" is now set before  do_auto_update() is called, so that "ver" can be used  in USB update scripts.  Patch by Martin Krause, 27 Oct 2005* Fix wrong usage of udelay() in led_blink() on trab board  Patch by Martin Krause, 27 Oct 2005* Fix udelay bug in vfd.c for trab board  Patch by Martin Krause, 27 Oct 2005* Disable JFFS2 support for trab board  Patch by Martin Krause, 27 Oct 2005* Change mtdparts definition on trab board to match current flash map  Patch by Martin Krause, 27 Oct 2005* Fix memory init problems on MCC200 board* Fix IxEthDB.h to compile again  Patch by Stefan Roese, 14 Jun 2006* Minor cleanup for PCS440EP board  Patch by Stefan Roese, 13 Jun 2006* Add MCF5282 support (without preloader)  relocate ichache_State to ram  u-boot can run from internal flash  Add EB+MCF-EV123 board support.  Add m68k Boards to MAKEALL  Patch from Jens Scharsig, 08 Aug 2005* Nios II - Add Altera EP1C20, EP1S10 and EP1S40 boards  Patch by Scott McNutt, 08 Jun 2006* Nios II - Add EPCS Controller bootrom work-around  -When booting from an epcs controller, the epcs bootrom may leave the  slave select in an asserted state causing soft reset hang. This  patch ensures slave select is negated at reset.  Patch by Scott McNutt, 08 Jun 2006* Update PK1C20 board  -Update base addresses for standard configuration  -Eliminate use of CACHE_BYPASS in board code  Patch by Scott McNutt, 08 Jun 2006* Nios II - Fix I/O Macros and mini-app stubs  -Fix asm/io.h macros  -Eliminate use of CACHE_BYPASS in cpu code  -Eliminate assembler warnings  -Fix mini-app stubs and force no small data  Patch by Scott McNutt, 08 Jun 2006* Fix U-Boot environment sector protection on MCC200 board* Minor cleanup for PCS440EP board* Update PCS440EP port to fit into one flash device (incl. environment)  Patch by Stefan Roese, 06 Jun 2006* Add support for PCS440EP board  Patch by Stefan Roese, 02 Jun 2006* Fix examples/Makefile; some build targets were lost* Fix watchdog handling in CFI flash driver  Just use udelay() when waiting for status changes which will  implicitely trigger the watchdog.* Fix PCI to memory window size problems on PM82x boards  We use the "automatic" mode that was used for  the  MPC8266ADS  and  MPC8272 boards. Eventually this should be used on all boards?]  Patch by Wolfgang Grandegger, 17 Jan 2006* Correct GPIO setup (UART1/IRQ's) on yosemite & yellowstone  Patch by Stefan Roese, 29 May 2006* Update Intel IXP4xx support  - Add IXP4xx NPE ethernet MAC support  - Add support for Intel IXDPG425 board  - Add support for Prodrive PDNB3 board  - Add IRQ support  Patch by Stefan Roese, 23 May 2006* Fix problem in PVR detection for 440GR  Patch by Stefan Roese, 18 May 2006* Fix gcc 3.4.x AFLAGS setting for m68k platform.* Enable autoboot for M5271EVB board.* Changed default ramdisk addr in yosemite/yellowstone ports  Patch by Stefan Roese, 15 May 2006* Fix PCMCIA support on virtlab2* Add support for VirtLab2 board  (needed because of differences in the PCMCIA hardware).* Minor cleanup.* Update yosemite configuration to enable flash write buffer support  Patch by Stefan Roese, 10 May 2006* Fix compile warnings in common/xyzModem.c  Patch by Stefan Roese, 10 May 2006* Add support for AMCC 440EP Rev C and 440GR Rev B  Patch by John Otken, 08 May 2006* OMAP 5912/OSK: update EMIFS CS1 timings:  Problems have been seen in the linux kernel's smc91x network driver  due to improper bus timings.  The latest 2.6 OMAP kernels currently  have a workaround, but this fix belongs in u-boot.  Patch by Kevin Hilman, 13 Oct 2005* Fix REG_MPU_LOAD_TIMER definition in multiple OMAP ports  Patch by Hiroki Kaminaga, 11 Mar 2006* Update omap5912osk board support  - Fix OMAP support that omap5912osk compiles in current source tree  - Update with code from "http://omap.spectrumdigital.com/osk5912"    to fix problems with DDR initialization  - Fix timer setup  - Use CFI flash driver and support complete 32MB of onboard flash  - Add "print_cpuinfo()" and "checkboard()" functions to display    CPU (with frequency) and Board infos  Patch by Stefan Roese, 10 May 2006* Fix watchdog issues for ColdFire boards.* Add M5271EVB board support.* Make R5200 specific low level initialization board conditional.* Update CPU target identification strings for ColdFire family.* Update register definitions for MCF5271.* Fix serial console support for MCF5271.* Fixes for gcc 3.4 based m68k toolchain,  based on patch by Jate Sujjavanich.* Fix lowboot support on MCC200 board* Merged MPC8349ADS and MPC8349EMDS ports into MPC8349EMDS port:  - Removed MPC8349ADS port  - Added PCI support to MPC8349ADS  - reworked memory map to allow mapping of all regions with BATs  Patch by Kumar Gala, 20 Apr 2006* Coding Style cleanup* Write RTC seconds first to maintain settings integrity per  Maxim/Dallas DS1306 data sheet.  Patch by Alan J. Luse, 02 May 2006* Scheduled for removal: strnicmp() which is unused* Update for Intel Monahans boards:  - support for magic key detection and handling on delta board  - NAND support for zylonite board + some minor cleanup* Declare load_serial_ymodem() when using CFG_CMD_LOADB.  Patch by Jon Loeliger, 01 May 2006* Fixed handling of bad checksums with "mkimage -l"* Added support for BC3450 board  Patch by Stefan Strobl, 21 Oct 2005* Update for NC650 board:  - Support rev1 and rev2 hardware  - adapt to new NAND layer  - add CP850 configuration based on NC650* MPC5200: enable snooping of DMA transactions on XLB even if no PCI  is configured; othrwise DMA accesses aren't cache coherent which  causes for example USB to fail.* Some code cleanup* Fix dbau1x00 boards broken by dbau1550 patch  PLL:s were not set for boards other than 1550.  Flash CFI caused card to hang due to undefined CFG_FLASH_BANKS_LIST.  Default boot is now bootp for cards other than 1550.  Patch by Thomas Lange, 10 Aug 2005* Fixes common/cmd_flash.c:  - fix some compiler/parser error, if using m68k tool chain  - optical fix for protect on/off all messages, if using more    then one bank  Patch by Jens Scharsig, 28 Jul 2005* Fix Quad UART mapping on MCC200 board due to new HW revision* Fix JFFS2 support for legacy NAND driver.* Remove dependencies between DoC code and old legacy NAND driver.* Fix PM828_PCI target, for which PCI was *not* configured in.* Fix Lite5200B support: initialize SDelay register  See Freescale's AN3221 "MPC5200B SDRAM Initialization and  Configuration", 3.3.1 SDelay--MBAR + 0x0190* Changes/fixes for drivers/cfi_flash.c:  - Add Intel legacy lock/unlock support to common CFI driver    On some Intel flash's (e.g. Intel J3) legacy unlocking is    supported, meaning that unlocking of one sector will unlock    all sectors of this bank. Using this feature, unlocking    of all sectors upon startup (via env var "unlock=yes") will    get much faster.  - Fixed problem with multiple reads of envronment variable    "unlock" as pointed out by Reinhard Arlt & Anders Larsen.  - Removed unwanted linefeeds from "protect" command when    CFG_FLASH_PROTECTION is enabled.  - Changed p3p400 board to use CFG_FLASH_PROTECTION  Patch by Stefan Roese, 01 Apr 2006* Changes/fixes for drivers/cfi_flash.c:  - Correctly handle the cases where CFG_HZ != 1000 (several    XScale-based boards)  - Fix the timeout calculation of buffered writes (off by a    factor of 1000)  Patch by Anders Larsen, 31 Mar 2006* Updates to common PPC4xx onboard (DDR)SDRAM init code (405 and 440)  405 SDRAM: - The SDRAM parameters can now be defined in the board	       config file and the 405 SDRAM controller values will	       be calculated upon bootup (see PPChameleonEVB).	       When those settings are not defined in the board	       config file, the register setup will be as it is now,	       so this implementation should not break any current	       design using this code.	       Thanks to Andrea Marson from DAVE for this patch.  440 DDR:   - Added function sdram_tr1_set to auto calculate the	       TR1 value for the DDR.	     - Added ECC support (see p3p440).  Patch by Stefan Roese, 17 Mar 2006* Fix CONFIG_SKIP_LOWLEVEL_INIT dependency in cpu/arm920t/start.S  Patch by Peter Menzebach, 13 Oct 2005 [DNX#2006040142000473]* Add support for ymodem protocol download  Patch by Stefano Babic, 29 Mar 2006* Memory Map Update for Delta board: U-Boot is at 0x80000000-0x84000000  Merge from Markus Klotzb點her's repo, 01 Apr 2006* GCC-4.x fixes: clean up global data pointer initialization for all  boards* Update for Delta board:  - redundant NAND environment  - misc Monahans cleanups (remove dead code etc.)  - DA9030 Initialization; some minimal changes to PXA I2C driver to