make it work with the Monahans.  - Make Monahans clock frequency configurable using    CFG_MONAHANS_RUN_MODE_OSC_RATIO and    CFG_MONAHANS_TURBO_RUN_MODE_RATIO.  Merge from Markus Klotzb點her's repo, 25 Mar 2006* Enable Quad UART om MCC200 board.* Cleanup MCC200 board configuration; omit non-existent stuff.* Add support for MPC859/866 Rev. A.0* Add command for handling DDR ECC registers on MPC8349EE MDS board.* Fix DDR ECC bit definitions for MPC83xx.* Add initial support for MPC8349E MDS board.* Add support for ECC DDR initialization on MPC83xx.* Add DMA support for MPC83xx.* Add sync in do_reset() routine for MPC83xx after RPR register  was written to. It is need on some targets when BAT translation  is enabled.* Add bit definitions for MPC83xx DDR controller registers.* Add Dcbz(), Dcbi() and Dcbf() routines for MPC83xx.* Correct shift offsets in icache_status and dcache_status for MPC83xx.* Add support for DS1374 RTC chip.* Add support for Lite5200B board.  Patch by  Patch by Jose Maria (Txema) Lopez, 16 Jan 2006* Apply SoC concept to arm926ejs CPUs, i.e. move the SoC specific  timer and cpu_reset code from cpu/$(CPU) into the new  cpu/$(CPU)/$(SOC) directories  Patch by Andreas Engel, 13 Mar 2006* Change max size of uncompressed uImage's to 8MByte and add  CFG_BOOTM_LEN to adjust this setting.  As mentioned by Robin Getz on 2005-05-24 the size of uncompressed  uImages was restricted to 4MBytes. This default size is now  increased to 8Mbytes and can be overrided by setting CFG_BOOTM_LEN  in the board config file.  Patch by Stefan Roese, 13 Mar 2006* Fix problem with updated PCI code in cpu/ppc4xx/405gp_pci.c  Patch by Stefan Roese, 13 Mar 2006* cpu/ppc4xx/start.S : exceptions are enabled after relocation  Patch by Cedric Vincent, 06 Jul 2005* au1x00_eth.c: check malloc return value and abort if it failed  Patch by Andrew Dyer, 26 Jul 2005* Change the sequence of events in soft_i2c.c:send_ack() to keep from  incorrectly generating start/stop conditions on the bus.  Patch by Andrew Dyer, 26 Jul 2005* Fix bug in [id]cache_status commands for MPC85xx processors;  should look at LSB of L1CSRn registers to determine if L1 cache is  enabled, not the MSB.  Patch by Murray Jensen, 19 Jul 2005* Fix array overflow with fw_setenv on uninitialised environment  Patch by Murray Jensen, 15 Jul 2005* Add support for EmbeddedPlanet EP88x boards  Patch by Yuli Barcohen, 13 Jul 2005* Remove board specific configuration includes from the common xilinx  ethernet and iic adapter code.  Patch by Michael Libeskind, 12 Jul 2005* Add Nat Semi DP83865 PHY support to MPC85xx TSEC driver  Patch by Murray Jensen, 08 Jul 2005* Add (some) definitions for the MPC85xx local bus controller  Patch by Murray Jensen, 08 Jul 2005* Add CPM2 I/O pin functions for MPC85xx processors  Patch by Murray Jensen, 08 Jul 2005* Fix compile problem* Added PCI support for MPC8349ADS board  Patch by Kumar Gala 11 Jan 2006* Enable address translation on MPC83xx  Patch by Kumar Gala, 10 Feb 2006* Decopuled setting of OR/BR and LBLAWBAR/LBLAWAR on MPC83xx  Patch by Kumar Gala, 25 Jan 2006* Fixed defines for MPC83xx SICRL register to match current specs  Patch by Kumar Gala, 23 Jan 2006* Only disable the MPC83xx watchdog if its enabled out of reset.  If its disabled out of reset SW can later enable it if so desired  Patch by Kumar Gala, 11 Jan 2006* Allow config of GPIO direction & data registers at boot on 83xx  Patch by Kumar Gala, 11 Jan 2006* Enable time handling on 83xx  Patch by Kumar Gala, 11 Jan 2006* Make System IO Config Registers board configurable on MPC83xx  Patch by Kumar Gala, 11 Jan 2006* Fixed PCI indirect config ops to handle multiple PCI controllers  We need to adjust the bus number we are trying to access based  on which PCI controller its on  Patch by Kumar Gala, 12 Jan 2006* Report back PCI bus when doing table based device config  Patch by Kumar Gala, 11 Jan 2006* Added support for PCI prefetchable region and BARs  If a host controller sets up a region as prefetchable and  a device's BAR denotes it as prefetchable, allocate the  BAR into the prefetch region.  If a BAR is prefetchable and no prefetchable region has  been setup by the controller we fall back to allocating  the BAR into the normally memory region.  Patch by Kumar Gala, 11 Jan 2006* Add helper function for generic flat device tree fixups for mpc83xx  Patch by Kumar Gala, 11 Jan 2006* Add support for passing initrd information via flat device tree  Patch by Kumar Gala, 11 Jan 2006* Added OF_STDOUT_PATH and OF_SOC  OF_STDOUT_PATH specifies the path to the device the kernel can use  for console output  OF_SOC specifies the proper name of the SOC node if one exists.  Patch by Kumar Gala, 11 Jan 2006* Allow board code to fixup the flat device tree before booting a kernel  Patch by Kumar Gala, 11 Jan 2006* Added CONFIG_ options for bd_t and env in flat dev tree	CONFIG_OF_HAS_BD_T will put a copy of the bd_t	into the resulting flat device tree.	CONFIG_OF_HAS_UBOOT_ENV will copy the environment	variables from u-boot into the flat device tree  Patch by Kumar Gala, 11 Jan 2006* Add support for the DHCP vendor optional bootfile (#67).  Ignores the vendor TFTP server name option (#66).  Patch by Murray Jensen, 30 Jun 2005* Fix a HW timing issue on 8548 CDS for eTSEC 3 in RGMII mode  Patch by Andy Fleming, 14 Jun 2005* Fix bad register definitions for LTX971 PHY on MPC85xx boards.  Patch by Gerhard Jaeger, 21 Jun 2005* Add netconsole and some more commands to RPXlite_DW board  Patch by Sam Song, 19 Jun 2005* Fix bad declaration on pci_cfgfunc_nothing  Patch by Sam Song, 19 Jun 2005* Adjust "echo" as a default command  Patch by Sam Song, 19 Jun 2005* Fix PCIDF calculation in cpu/mpc8260/speed.c for MPC8280EC  Patch by KokHow Teh, 16 Jun 2005* Add crc of data to jffs2 (in jffs2_1pass_build_lists()).  Patch by Rick Bronson, 15 Jun 2005* Coding Style cleanup* Avoid dereferencing NULL in find_cmd() if no valid commands were found  Patch by Andrew Dyer, 13 Jun 2005* Add ADI Blackfin support  - add support for Analog Devices Blackfin BF533 CPU  - add support for the ADI BF533 Stamp uClinux board  - add support for the ADI BF533 EZKit board  Patches by Richard Klingler, 11 Jun 2005* Add loads of ntohl() in image header handling  Patch by Steven Scholz, 10 Jun 2005* Switch MPC86xADS and MPC885ADS boards to use cpuclk environment  variable to set clock  Patch by Yuli Barcohen, 05 Jun 2005* RPXlite configuration fixes  - Use correct flash sector size  - Use correct memory test end address  - Add support for bzip2 compression  - Various small fixes  Patch by Yuli Barcohen, 05 Jun 2005* Memory configuration changes for ZPC.1900 board  - Fix SDRAM timing on both local bus and 60x bus  - Add support for second flash bank (SIMM)  - Change boot flash base  Patch by Yuli Barcohen, 05 Jun 2005* Add support for Adder boards with 16MB SDRAM;  add support for second FEC on Adder87x board.  Patch by Yuli Barcohen, 05 Jun 2005* Fix conditional for including ks8695eth driver  Patch by Greg Ungerer, 04 Jun 2005* Fix Makefile: include config.mk only after CROSS_COMPILE is defined  Patch by Friedrich Lobenstock, 02 Jun 2005* Fix comment in common/soft_i2c.c  Patches by Peter Korsgaard/Tolunay Orkun, 26 May 2005* Cleanup compiler warnings.  Patch by Greg Ungerer, 21 May 2005* Word alignment fixes for word aligned NS16550 UART  Patch by Jean-Paul Saman, 01 Mar 2005  Fixes bug with UART that only supports word aligned access: removed  "__attribute__ ((packed));" for "(CFG_NS16550_REG_SIZE == 4)" some  (broken!) versions of GCC generate byte accesses when encountering  the packed attribute regardless if the struct is already correctly  aligned for a platform. Peripherals that can only handle word  aligned access won't work properly when accessed with byte access.  The struct NS16550 is already word aligned for REG_SIZE = 4, so  there is no need to packed the struct in that case.* Fix behaviour if gatewayip is not set  Patch by Robin Gilks, 23 Dec 2004* Fix cleanup for netstart board.  Remove build results from repository* Some code cleanup for GCC 4.x* Fixes to support environment in NAND flash;  enable NAND flash based environment for delta board.* Add support for Intel Monahans CPU on Zylonite and Delta boards  (This is Work in Progress!)* Add support for TQM8260-AI boards.* Minor code cleanup* Merge the new NAND code (testing-NAND brach); see doc/README.nand  Rewrite of NAND code based on what is in 2.6.12 Linux kernel  Patch by Ladislav Michl, 29 Jun 2005* Add lowboot target to mcc200 board  Patch by Stefan Roese, 4 Mar 2006* Fix problem with flash_get_size() from CFI driver update  Patch by Stefan Roese, 1 Mar 2006* Make CFG_NO_FLASH work on ARM systems  Patch by Markus Klotzbuecher, 27 Feb 2006* Update mcc200 config: Disable PCI and DoC, use 133 MHz IPB clock,  use hush shell.* Convert mcc200 to use common CFI flash driver  Patch by Stefan Roese, 28 Feb 2006* Add env-variable "unlock" to handle initial state of sectors  (locked/unlocked).  Only the U-Boot image and it's environment is protected,  all other sectors are unprotected (unlocked) if flash  hardware protection is used (CFG_FLASH_PROTECTION) and  the environment variable "unlock" is set to "yes".  Patch by Stefan Roese, 28 Feb 2006* Update drivers/cfi_flash.c:  - find_sector() called in both versions of flash_write_cfiword()  Patch by Peter Pearse, 27th Feb 2006* CFI support for a x8/x16 AMD/Spansion flash configured in x8 mode  Patch by Jose Maria Lopez, 16 Jan 2006* Add support for AMD/Spansion Flashes in flash_write_cfibuffer  Patch by Alex Bastos and Thomas Schaefer, 2005-08-29* Changes/fixes for drivers/cfi_flash.c:  We *should* check if there are any error bits if the previous call  returned ERR_OK (Otherwise we will have output an error message in  flash_status_check() already.)  The original code would only check for  error bits if flash_status_check() returns ERR_TIMEOUT.  Patch by Marcus Hall, 23 Aug 2005* Changes/fixes for drivers/cfi_flash.c:  - Add CFG_FLASH_PROTECT_CLEAR on drivers/cfi_flash.c  - Prohibit buffer write when buffer_size is 1 on drivers/cfi_flash.c  Patch by Sangmoon Kim, 19 Aug 2005* Fixes for drivers/cfi_flash.c:  - Fix wrong timeout value usage in flash_status_check()  - Round write_tout up when converting to msec in flash_get_size()  - Remove clearing flash status at the end of flash_write_cfibuffer()    which sets Intel 28F640J3 flash back to command mode on CSB472  Patch by Tolunay Orkun, 02 July 2005* Add basic support for the SMMACO4 Board from PanDaCom.  Patch by Heiko Schocher, 20 Feb 2006* Add GIT version information (commid ID) to untagged U-Boot versions  As done in the linux kernel, the U-Boot version (U_BOOT_VERSION)  of all unreleased (untagged) U-Boot images will be automatically  extended upon compiletime with a part of the GIT commit ID and  possibly with "dirty" if uncommited changes are detected.  Here an example for the resulting version:  "U-Boot 1.1.4-g3457ac18-dirty"  The version is now maintained in the toplevel Makefile and the  version headers are autogenerated.  Patch by Stefan Roese, 9 Feb 2006* Update default environment for INKA4x00 board.* Convert CPCI750 to use common CFI flash driver  Patch by Reinhard Arlt, 8 Feb 2006* Various changes to esd HH405 board specific files  Patch by Matthias Fuchs, 07 Feb 2006* Cleanup U-Boot boot messages on ARM.  To match the U-Boot user interface on ARM platforms to the U-Boot  standard (as on PPC platforms), some messages with debug character  are removed from the default U-Boot build.  Enable DEBUG for lib_arm/board.c to enable debug messages.  New CONFIG_DISPLAY_CPUINFO and CONFIG_DISPLAY_BOARDINFO options.  Patch	 by Stefan Roese, 24 Jan 2006* Fix various compiler warnings on ppc4xx builds (ELDK 4.0)  Patch by Stefan Roese, 18 Jan 2006* Add VGA support (CT69000) to CPCI750 board.  Insert missing __le32_to_cpu() for filesize in ext2fs_read_file().  Patch by Reinhard Arlt, 30 Dec 2005* PMC405 and CPCI405: Moved configuration of pci resources  into config file.  PMC405 and CPCI2DP: Added firmware download and booting via pci.  Patch by Matthias Fuchs, 20 Dec 2005* Add ColdFire targets to MAKEALL script  Patch by Zachary Landau, 26 Jan 2006* Add support for r5200 board  Patch by Zachary Landau, 26 Jan 2006* Add support for Freescale M5271 processor  Patch by Zachary Landau, 26 Jan 2006* Fix 28F256J3A support on PM520 board  (without bank-switching only 32 MB can be accessed)* Fix mkimage bug with multifile images created on 64 bit systems.* Add support for 28F256J3A flash (=> 64 MB) on PM520 board* Fix compiler problem with at91rm9200dk board.  Patch by Eugen Bigz, 19 Dec 2005