#include "exp4_2407.h"
void cpu_ini(void)

{

	asm(" nop ");
	asm(" nop ");
	asm(" nop ");
    asm(" setc INTM");         //禁止所有中斷 ST0.9=INTM
    asm(" clrc SXM");          //抑制符號位擴展
    asm(" clrc OVM");          //累加器中結果正常溢出
    asm(" clrc CNF");          //配置 B0為數據儲存器

/*** Configure the System Control and Status registers ***/    
//    * SCSR1=0x0EFD;            //配置時鐘鎖相為0.5倍頻CLKOUT=0.5*10MHZ=5MHZ,MAX CPU freq
/*
 bit 15        0:      reserved
 bit 14        0:      CLKOUT = CPUCLK
 bit 13-12     00:     IDLE1 selected for low-power mode when execute IDLE instruction
 bit 11-9      111:    PLL x0.5 mode
 bit 8         0:      reserved
 bit 7         1:      1 = enable ADC module clock
 bit 6         1:      1 = enable SCI module clock
 bit 5         1:      1 = enable SPI module clock
 bit 4         1:      1 = enable CAN module clock
 bit 3         1:      1 = enable EVB module clock
 bit 2         1:      1 = enable EVA module clock
 bit 1         0:      reserved
 bit 0         1:      clear the ILLADR bit
*/    
//    * SCSR1=0x0EFD;            //配置時鐘鎖相為0.5倍頻CLKOUT=0.5*10MHZ=5MHZ
//    * SCSR1=0x0CFD;            //*0.57
//    * SCSR1=0x0AFD;            //*0.66
//    * SCSR1=0x08FD;            //*0.8
      * SCSR1=0x06FD;            //*1
//    * SCSR1=0x04FD;            //*1.33
//      * SCSR1=0x02FD;          //*2 
      *SCSR2 = (*SCSR2 | 0x000B) & 0x000F;
    
/*
 bit 15-7      0's:    reserved
 bit 6         0:      Input Qualifier Clocks=5 clock
 bit 5         0:      D'ont write this bit.allows  user to disable WD through the WDDIS bit in the WDCR.
 bit 4         0:      XMIF_HI-Z, 0=normal mode, 1=Hi-Z'd
 bit 3         1:      disable the boot ROM, enable the FLASH
 bit 2         no change   MP/MC* bit reflects state of MP/MC* pin
 bit 1-0      11:      11 = SARAM mapped to prog and data
*/
    
/*** Disable the watchdog timer ***/
          
    * WDCR=0x00EF;             //禁止看門狗
/*
 bits 15-8     0's:     reserved
 bit 7         1:       clear WD flag
 bit 6         1:       disable the dog
 bit 5-3       101:     must be written as 101
 bit 2-0       111:     WDCLK divider = 64  WDCLK= CLKOUT/512
*/
	
/*** Setup external memory interface for LF2407  ***/
    WSGR = 0x01FF;
/*
 bit 15-11     0's:    reserved
 bit 10-9      00:     bus visibility off
 bit 8-6       111:    7 wait-state for I/O space
 bit 5-3       111:    7 wait-state for data space
 bit 2-0       111:    7 wait state for program space
*/	

/*** Setup shared I/O pins ***/
    *MCRA = 0x0000;  /* group A pins */
/*
 bit 15        0:      0=IOPB7,     1=TCLKINA
 bit 14        0:      0=IOPB6,     1=TDIRA
 bit 13        0:      0=IOPB5,     1=T2PWM/T2CMP
 bit 12        0:      0=IOPB4,     1=T1PWM/T1CMP
 bit 11        0:      0=IOPB3,     1=PWM6
 bit 10        0:      0=IOPB2,     1=PWM5
 bit 9         0:      0=IOPB1,     1=PWM4
 bit 8         0:      0=IOPB0,     1=PWM3
 bit 7         0:      0=IOPA7,     1=PWM2
 bit 6         0:      0=IOPA6,     1=PWM1
 bit 5         0:      0=IOPA5,     1=CAP3
 bit 4         0:      0=IOPA4,     1=CAP2/QEP2
 bit 3         0:      0=IOPA3,     1=CAP1/QEP1
 bit 2         0:      0=IOPA2,     1=XINT1
 bit 1         0:      0=IOPA1,     1=SCIRXD
 bit 0         0:      0=IOPA0,     1=SCITXD
*/

    *MCRB = 0xFE03;    /* group B pins */
/*
 bit 15        1:      0=reserved,  1=TMS2 (always write as 1)
 bit 14        1:      0=reserved,  1=TMS  (always write as 1)
 bit 13        1:      0=reserved,  1=TD0  (always write as 1)
 bit 12        1:      0=reserved,  1=TDI  (always write as 1)
 bit 11        1:      0=reserved,  1=TCK  (always write as 1)
 bit 10        1:      0=reserved,  1=EMU1 (always write as 1)
 bit 9         1:      0=reserved,  1=EMU0 (always write as 1)
 bit 8         0:      0=IOPD0,     1=XINT2/ADCSOC
 bit 7         0:      0=IOPC7,     1=CANRX
 bit 6         0:      0=IOPC6,     1=CANTX
 bit 5         0:      0=IOPC5,     1=SPISTE
 bit 4         0:      0=IOPC4,     1=SPICLK
 bit 3         0:      0=IOPC3,     1=SPISOMI
 bit 2         0:      0=IOPC2,     1=SPISIMO
 bit 1         1:      0=IOPC1,     1=BIO*
 bit 0         1:      0=IOPC0,     1=W/R*
*/

    *MCRC = 0x0001;    /* group C pins */
/*
 bit 15        0:      reserved
 bit 14        0:      0=IOPF6,     1=IOPF6
 bit 13        0:      0=IOPF5,     1=TCLKINB
 bit 12        0:      0=IOPF4,     1=TDIRB
 bit 11        0:      0=IOPF3,     1=T4PWM/T4CMP
 bit 10        0:      0=IOPF2,     1=T3PWM/T3CMP
 bit 9         0:      0=IOPF1,     1=CAP6
 bit 8         0:      0=IOPF0,     1=CAP5/QEP4
 bit 7         0:      0=IOPE7,     1=CAP4/QEP3
 bit 6         0:      0=IOPE6,     1=PWM12
 bit 5         0:      0=IOPE5,     1=PWM11
 bit 4         0:      0=IOPE4,     1=PWM10
 bit 3         0:      0=IOPE3,     1=PWM9
 bit 2         0:      0=IOPE2,     1=PWM8
 bit 1         0:      0=IOPE1,     1=PWM7
 bit 0         1:      0=IOPE0,     1=CLKOUT    
*/

/*** Configure IOPA pin as an INPUT ***/
    *PADATDIR = *PADATDIR & 0x00FF;
 
/*** Configure IOPB pin as an INPUT ***/
    *PBDATDIR = *PBDATDIR & 0x00FF;
    
/*** Configure IOPC pin as an INPUT ***/
    *PCDATDIR = *PCDATDIR & 0x00FF;
    
/*** Configure IOPD pin as an INPUT ***/
    *PDDATDIR = *PDDATDIR & 0xFEFF; 

/*** Configure IOPE pin as an INPUT ***/
    *PEDATDIR = *PEDATDIR & 0x00FF; 
    
/*** Configure IOPF pin as an INPUT ***/
    *PFDATDIR = *PFDATDIR & 0x7FFF;           
    

/*** Setup timers 1 and 2, and the PWM configuration ***/
    *T1CON = 0x0000;                    /* disable timer 1 */
    *T2CON = 0x0000;                    /* disable timer 2 */

    *GPTCONA = 0x0000;                  /* configure GPTCONA */
    *GPTCONB = 0x0000;                  /* configure GPTCONB */
/*     
 bit 15        0:      reserved
 bit 14        0:      T2STAT, read-only
 bit 13        0:      T1STAT, read-only
 bit 12-11     00:     reserved
 bit 10-9      00:     T2TOADC, 00 = no timerX event starts ADC
 bit 8-7       00:     T1TOADC, 00 = no timerX event starts ADC
 bit 6         0:      TCOMPOE, 0 = Hi-z all timer compare outputs
 bit 5-4       00:     reserved
 bit 3-2       00:     TXPIN, 00 = forced low
 bit 1-0       00:     TXPIN, 00 = forced low
*/

 
    /*開總中斷*/
     asm(" clrc INTM");  
    /*使能int1中斷*/
     * IMR=0x0001;                  
    /*使能xint1中斷,下降沿有效,高優先級,清xint1中斷標志*/
     * XINT1CR=0x8001;          
     * IFR=0xFFFF;              //清除所有中斷標志,"寫1清0"  
}

    

interrupt void  nothing()
{
return;
}