/************************************************************* * File: include/l65066.h * Purpose: Include file for L65066 (DCAM-111) * Author: Phil Bunce (pjb@carmel.com) * Revision History: *	990212	Created from L9a0084.h */#if defined(L65066) && !defined(_L65066_H_)#define _L65066_H_/* * Defines for the L65066 (DCAM-111) */#ifndef LR4102#define LR4102#endif#include <lr4102.h>/*#define USE_FBUS	/* enable this when switching to the fbus */#define M_084_R		0xbe100000#define M_084_TC0	0xbe200000#define M_084_TCOUNT0	0xbe200004#define M_084_RCOUNT0	0xbe200008#define M_084_TC1	0xbe200010#define M_084_TCOUNT1	0xbe200014#define M_084_RCOUNT1	0xbe200018#define M_084_RTCC	0xbe200020#define M_084_RTCCOUNT	0xbe200024#define M_084_RTCLOAD	0xbe200028#define M_084_SYSCLK	0xbe300000#define SYSCLK_MCLKENP	(1<<0)#define SYSCLK_BIUCLK	(1<<10)#define SYSCLK_TMR0CLK	(1<<12)#define SYSCLK_TMR1CLK	(1<<13)#define SYSCLK_SIO0CLK	(1<<14)#define SYSCLK_SIO1CLK	(1<<15)#define SYSCLK_SIO2CLK	(1<<16)#define M_084_ACLKDIV0	0xbe300004#define M_084_ACLKDIV1	0xbe300008#define M_084_ACLKDIV2	0xbe30000c#define ACLKDIV_DIV	(0xff<<0)#define ACLKDIV_DB4	(1<<8)#define ACLKDIV_EN	(1<<9)#define ACLKDIV_CSEL	(3<<10)  /* 13.5MHz,20.25MHz,ext2,ext3 */#define M_084_BDC	0xbe400000#define M_084_D0C	0xbe400004#define M_084_D1C	0xbe400008#define M_084_D2C	0xbe40000c#define M_084_D3C	0xbe400010#define M_084_REFRESH	0xbe40001c/*  * Baud rate calculations * 	Assumes ACLKDIV0:CSEL = 0 (13.5MHz) *	Assumes SOC0=SIC0:CSEL = 1 (iaclkp0) * *	Baud	DIV	DB4 *      ------------------- *	1200	176	1 *	2400	 88	1 *	4800	176	0 *	9600	 88	0 *	19200	 44	0 *	38400	 22	0 *//* serial port 0 */#define M_084_SOD0	0xbe900000 /* TX */#define M_084_SOC0	0xbe900004 /* TX control */#define M_084_SID0	0xbe900008 /* RX */#define M_084_SIC0	0xbe90000c /* RX control *//* serial port 1 */#define M_084_SOD1	0xbe900010#define M_084_SOC1	0xbe900014#define M_084_SID1	0xbe900018#define M_084_SIC1	0xbe90001c/* serial port 2 */#define M_084_SOD2	0xbe900020#define M_084_SOC2	0xbe900024#define M_084_SID2	0xbe900028#define M_084_SIC2	0xbe90002c/* bit defs for SOC */#define SOC_EN	   (1<<0)	/* enable */#define SOC_SD	   (1<<1)	/* shift direction *//* uart convention is ls bit 1st ie SD=1 */#define SOC_SM	   (1<<2)	/* synchronous mode */#define SOC_DB1	   (1<<3)	/* delay by one */#define SOC_STP	   (1<<4)	/* stop bits 0=1 1=2 */#define SOC_FC	   (1<<5)	/* cts control */#define SOC_LEN	   (1<<6)	/* 0=8bits 1=7bits */#define SOC_PARITY (3<<7) 	/* none,odd,even,nonee */#define SOC_CI	   (1<<9)	/* clock invert */#define SOC_CSEL   (3<<10) 	/* clock select sclkp,iaclkp0,iaclkp1,iaclkp2*/#define SOC_CSEL_1 (1<<10) 	/* clock select iaclkp0 */#define SOC_CSELSHFT 10 	/* clock select shift amount */#define SOC_FA	   (1<<14)	/* frame active */#define SOC_SFNF   (1<<15) 	/* fifo not full */#define SOC_PDAT   (0xf<<16) 	/* pin data */#define SOC_PCFG   (0xf<<20) 	/* pin config *//* bit defs for SIC */#define SIC_EN	   (1<<0)	/* enable */#define SIC_SD	   (1<<1)	/* shift direction */#define SIC_SM	   (1<<2)	/* syncronous mode */#define SIC_DB1	   (1<<3)	/* delay by one */#define SIC_LEN	   (1<<6)	/* 0=8bits 1=7bits */#define SIC_PARITY (3<<7) 	/* none,odd,even,nonee */#define SIC_CI	   (1<<9)	/* clock invert */#define SIC_CSEL   (3<<10) 	/* clock select */#define SIC_CSEL_1 (1<<10) 	/* clock select iaclkp0 */#define SIC_CSELSHFT 10 	/* clock select shift amount */#define SIC_FA	   (1<<14)	/* frame active */#define SIC_SFNE   (1<<15) 	/* fifo not empty */#define SIC_PDAT   (0xf<<16) 	/* pin data */#define SIC_PCFG   (0xf<<20) 	/* pin config */#define SIC_FE	   (1<<28)	/* framing error */#define SIC_PE	   (1<<29)	/* parity error */#define SIC_OVE	   (1<<30)	/* overrun error */#define SIC_SE	   (1<<31)	/* sum of error *//* interrupt handler */#define M_084_ICAUSE	0xbea00000#define M_084_IMASK	0xbea00004#endif /*  _L65066_H_ */