?? def9603.h
字號:
/**********************************************************************/
/* 9603 I/O address definition */
/**********************************************************************/
//#define USBN9603_addr 0x0000
/**********************************************************************/
/* 9603 register and bit definitions */
/**********************************************************************/
#define MCNTRL 0x00 /*Main control register */
#define CCONF 0x01 /*Clk. config. register */
//Regster 0x02 is Reserved
//#define TCR 0x02 /*Xcvr config. register */
#define RID 0x03 /*Rev. ID register */
#define FAR 0x04 /*Func address register */
#define NFSR 0x05 /*Node func st register */
#define MAEV 0x06 /*Main event register */
#define MAMSK 0x07 /*Main mask register */
#define ALTEV 0x08 /*Alt. event register */
#define ALTMSK 0x09 /*ALT mask register */
#define TXEV 0x0A /*TX event register */
#define TXMSK 0x0B /*TX mask register */
#define RXEV 0x0C /*RX event register */
#define RXMSK 0x0D /*RX mask register */
#define NAKEV 0x0E /*NAK event register */
#define NAKMSK 0x0F /*NAK mask register */
#define FWEV 0x10 /*FIFO warning register */
#define FWMSK 0x11 /*FIFO warning mask */
#define FNH 0x12 /*Frame nbr hi register */
#define FNL 0x13 /*Frame nbr lo register */
#define DMACNTRL 0x14 /*DMA control register */
#define DMAEV 0x15 /*DMA event register */
#define DMAMSK 0x16 /*DMA Mask register */
#define MIR 0x17 /*mirror register */
#define DMACNT 0x18 /*DMA Count register */
#define DMAERR 0x19 /*DMA Error register */
//Regster 0x1A is Reserved
#define WKUP 0x1B /*Wakeup register */
//Regster 0x1C is Reserved
//Regster 0x1D is Reserved
//Regster 0x1E is Reserved
//Regster 0x1F is Reserved
#define EPC0 0x20 /*Endpoint0 register */
#define TXD0 0x21 /*TX data register 0 */
#define TXS0 0x22 /*TX status register 0 */
#define TXC0 0x23 /*TX command register 0 */
//Regster 0x24 is Reserved
#define RXD0 0x25 /*RX data register 0 */
#define RXS0 0x26 /*RX status register 0 */
#define RXC0 0x27 /*RX command register 0 */
#define EPC1 0x28 /*Endpoint1 register */
#define TXD1 0x29 /*TX data register 1 */
#define TXS1 0x2A /*TX status register 1 */
#define TXC1 0x2B /*TX command register 1 */
#define EPC2 0x2C /*Endpoint2 register */
#define RXD1 0x2D /*RX data register 1 */
#define RXS1 0x2E /*RX status register 1 */
#define RXC1 0x2F /*RX command register 1 */
#define EPC3 0x30 /*Endpoint3 register */
#define TXD2 0x31 /*TX data register 2 */
#define TXS2 0x32 /*TX status register 2 */
#define TXC2 0x33 /*TX command register 2 */
#define EPC4 0x34 /*Endpoint4 register */
#define RXD2 0x35 /*RX data register 2 */
#define RXS2 0x36 /*RX status register 2 */
#define RXC2 0x37 /*RX command register 2 */
#define EPC5 0x38 /*Endpoint5 register */
#define TXD3 0x39 /*TX data register 3 */
#define TXS3 0x3A /*TX status register 3 */
#define TXC3 0x3B /*TX command register 3 */
#define EPC6 0x3C /*Endpoint6 register */
#define RXD3 0x3D /*RX data register 3 */
#define RXS3 0x3E /*RX status register 3 */
#define RXC3 0x3F /*RX command register 3 */
/* MCNTRL bits ********************************************************/
#define SRST 0x01 /*software reset */
#define DBG 0x02 /*debug mode */
#define VGE 0x04 /*voltage regulator enable*/
#define NAT 0x08 /*node attached */
#define INT_DIS 0x00 /*interrupts disabled */
#define INT_L_O 0x40 /*act lo ints, open drain */
#define INT_H_P 0x80 /*act hi ints, push pull */
#define INT_L_P 0xC0 /*act lo ints, push pull */
/* CCONF bits ********************************************************/
#define CODIS 0x80 /*disable clock output */
/* FAR bits ********************************************************/
#define AD_EN 0x80 /*address enable */
/* EPCX bits ********************************************************/
#define DEF 0x40 /*force def. adr (0 only) */
#define STALL 0x80 /*force stall handshakes */
#define ISO 0x20 /*set for isochr. (1-3) */
#define EP_EN 0x10 /*enables endpt. (1-3) */
/* NFSR bits ********************************************************/
#define RST_ST 0x00 /*reset state */
#define RSM_ST 0x01 /*resume state */
#define OPR_ST 0x02 /*operational state */
#define SUS_ST 0x03 /*suspend state */
/* MAEV, MAMSK bits ***************************************************/
#define WARN 0x01 /*warning bit has been set*/
#define ALT 0x02 /*alternate event */
#define TX_EV 0x04 /*transmit event */
#define FRAME 0x08 /*SOF packet received */
#define NAK 0x10 /*NAK event */
#define ULD 0x20 /*unlock locked detected */
#define RX_EV 0x40 /*receive event */
#define INTR_E 0x80 /*master interrupt enable */
/* ALTEV, ALTMSK bits *************************************************/
#define EOP 0x08 /*end of packet */
#define SD3 0x10 /*3 ms suspend */
#define SD5 0x20 /*5 ms suspend */
#define RESET_A 0x40 /*reset detected */
#define RESUME_A 0x80 /*resume detected */
/* TXEV, TXMSK bits ***************************************************/
#define TXFIFO0 0x01 /*TX_DONE, FIFO 0 */
#define TXFIFO1 0x02 /*TX_DONE, FIFO 1 */
#define TXFIFO2 0x04 /*TX_DONE, FIFO 2 */
#define TXFIFO3 0x08 /*TX_DONE, FIFO 3 */
#define TXUDRN0 0x10 /*TX_URUN, FIFO 0 */
#define TXUDRN1 0x20 /*TX_URUN, FIFO 1 */
#define TXUDRN2 0x40 /*TX_URUN, FIFO 2 */
#define TXUDRN3 0x80 /*TX_URUN, FIFO 3 */
/* RXEV, RXMSK bits ***************************************************/
#define RXFIFO0 0x01 /*RX_DONE, FIFO 0 */
#define RXFIFO1 0x02 /*RX_DONE, FIFO 1 */
#define RXFIFO2 0x04 /*RX_DONE, FIFO 2 */
#define RXFIFO3 0x08 /*RX_DONE, FIFO 3 */
#define RXOVRN0 0x10 /*RX_OVRN, FIFO 0 */
#define RXOVRN1 0x20 /*RX_OVRN, FIFO 1 */
#define RXOVRN2 0x40 /*RX_OVRN, FIFO 2 */
#define RXOVRN3 0x80 /*RX_OVRN, FIFO 3 */
/* NAKEV, NAKMSK bits *************************************************/
#define NAK_I0 0x01 /*IN NAK, FIFO 0 */
#define NAK_I1 0x02 /*IN NAK, FIFO 1 */
#define NAK_I2 0x04 /*IN NAK, FIFO 2 */
#define NAK_I3 0x08 /*IN NAK, FIFO 3 */
#define NAK_O0 0x10 /*OUT NAK, FIFO 0 */
#define NAK_O1 0x20 /*OUT NAK, FIFO 1 */
#define NAK_O2 0x40 /*OUT NAK, FIFO 2 */
#define NAK_O3 0x80 /*OUT NAK, FIFO 3 */
/* TXCx bits ********************************************************/
#define TX_EN 0x01 /*transmit enable */
#define TX_LAST 0x02 /*last data in FIFO */
#define TX_TOGL 0x04 /*specifies PID used */
#define FLUSH 0x08 /*flushes all FIFO data */
#define IGN_IN 0x10 /*ignore in tokens */
/* TXS0 bits ********************************************************/
#define TX_DONE 0x20 /*transmit done */
#define ACK_STAT 0x40 /*ack status of xmission */
/* RXC0 bits ********************************************************/
#define RX_EN 0x01 /*receive enable */
#define IGN_OUT 0x02 /*ignore out tokens */
#define IGN_SETUP 0x04 /*ignore setup tokens */
/* RXS0 bits ********************************************************/
#define RX_LAST 0x10 /*indicates RCOUNT valid */
#define RX_TOGL 0x20 /*last pkt was DATA1 PID */
#define SETUP_R 0x40 /*setup packet received */
#define RX_ERR 0x80 /*last packet had an error*/
/* Some new 9603 bits *************************************************/
/* WKUP bits ********************************************************/
#define PNDUSB 0x01 /* Pending USB WakeUp */
#define PNDUC 0x02 /* Pending uC WakeUp */
#define ENUSB 0x04 /* Enable USB */
#define ENUC 0x08 /* Enable Microcontroller */
#define WKMODE 0x20 /* Wake Up Mode */
#define HOS 0x40 /* Halt On Suspend */
#define FHT 0x80 /* Force Halt */
/**********************************************************************/
/* 9602 commands and constants */
/**********************************************************************/
#define USBREAD 0x00 /*reads data at spec. addr*/
#define USBWRITE 0x80 /*write selected register */
#define USBBURST 0xC0 /*burst write */
/* RCOUNT bits ********************************************************/
#define RCOUNT 0x0F?? 快捷鍵說明
復制代碼
Ctrl + C
搜索代碼
Ctrl + F
全屏模式
F11
切換主題
Ctrl + Shift + D
顯示快捷鍵
?
增大字號
Ctrl + =
減小字號
Ctrl + -