function [dscdma_open_ber3]=dscdma_open_looptest3(snr_in_dB)

%******************** Preparation part **********************

sr=256000.0; % Symbol rate
ml=1;        % Number of modulation levels
br=sr.*ml;   % Bit rate (=symbol rate in this case)
nd = 1;
N=nd;% Number of symbols that simulates in each loop
E=1;
snr=10^(snr_in_dB/10);     % Eb/N0
sgma=sqrt(E/snr)/2;
IPOINT=8;    % Number of oversamples

%******************* Filter initialization ********************

irfn=21;     % Number of filter taps          
alfs=0.5;    % Rolloff factor
[xh] = hrollfcoef(irfn,IPOINT,sr,alfs,1);   %Transmitter filter coefficients 
[xh2] = hrollfcoef(irfn,IPOINT,sr,alfs,0);  %Receiver filter coefficients 

m=32;    %擴頻碼的碼片數目


%********************** Spreading code initialization **********************

user  = 2;                                                          % number of users
seq   = 3;                                                          % 1:M-sequence  2:Gold  3:Orthogonal Gold
stage = 5;                                                          % number of stages
ptap1 = [1 3];                                                      % position of taps for 1st
ptap2 = [2 3];                                                      % position of taps for 2nd
regi1 = [1 1 1 1 1];                                                    % initial value of register for 1st
regi2 = [1 1 1 1 1];                                                    % initial value of register for 2nd

%******************** Generation of the spreading code *********************

switch seq
case 1                                                              % M-sequence
    code = mseq(stage,ptap1,regi1,user);
case 2                                                              % Gold sequence
    m1   = mseq(stage,ptap1,regi1);
    m2   = mseq(stage,ptap2,regi2);
    code = goldseq(m1,m2,user);
case 3                                                              % Orthogonal Gold sequence
    m1   = mseq(stage,ptap1,regi1);
    m2   = mseq(stage,ptap2,regi2);
    code = [goldseq(m1,m2,user),zeros(user,1)];
end
code = code * 2 - 1;
code=code';
clen = length(code);

%**************************** START CALCULATION ****************************

nloop = 10000;                                                       % simulation number of times
noe   = 0;
nod   = 0;

for iii=1:nloop
    
%****************************** Transmitter ********************************
    data0= rand(1,nd*ml) > 0.5;
    
%******************** 第一路 BPSK 調制 ***********************  

      data=data0.*2-1; %————————測試點————————

%data1=spread(data,code(:,1)) %第一路天線需要發射的信號————————測試點16  nd=2
data_1=data*code(:,1);

%[data2] = oversamp( data1, N*m , IPOINT)                 %128  -1,0,1
%[data3] = conv(data2,xh) % conv: built in function--------測試點  295

%******************** 第二路 BPSK 調制 ********************
%********************擴展原始碼元以實現擴頻序列*************

%data2=spread(data,code(:,2))
data_2=data*code(:,2);            %第二路天線需要發射的信號————————測試點16
%[data_2] = oversamp( data_1, N*m , IPOINT)                 %128  -1,0,1
%[data_3] = conv(data_2,xh) % conv: built in function--------測試點  295


%******************產生空間路徑衰落系數矩陣*******************
%******************產生空間路徑衰落系數矩陣*******************
%Nr=1;
%Nt=2;
%t=1;
%h=mimo_channel(Nr,Nt,t);  %********2 x 1 天線********
%receiver1=1/sqrt(2)*(h(1,1)*data1+h(1,2)*data_1);  %------16復數
h=randn(1,2)+randn(1,2)*j;
receiver1=1/sqrt(2)*(h(1,1)*data_1+h(1,2)*data_2);

%****************** Attenuation Calculation *****************
	
   % spow=sum(data_1.*data_1)/nd          
	%attn=0.5*spow*sr/br*10.^(-ebn0/10)
	%attn=sqrt(attn)
  

%************ Add White Gaussian Noise (AWGN) ***************
	
    inoise=(randn(1,length(data_1)).*attn)'  % randn: built in function
    %for t=1:length(data_1)
    %inoise(t)=gngauss(sgma);
    %end
    
    inoise_1=inoise';
	data4=receiver1+inoise_1;
	%data5=conv(data4,xh2)  % conv: built in function  ---------462復數

	%sampl=irfn*IPOINT+1;
	%data6 = data5(sampl:8:8*nd+sampl-1)  %-------2個復數 
    
    
 %****************************解擴信號************************
           
           data_7=code(:,1)'*data4;            
           %data7=despread(data4,code(:,1))
           data_8=code(:,2)'*data4;
           %data8=despread(data4,code(:,2))   
           data9=conj(h(1,1))*data_7+conj(h(1,2))*data_8;      
           %data_9=1/sqrt(2)*((abs(h(1,1)))^2+(abs(h(1,2)))^2)*data+(conj(h(1,1))*code(1,:)+conj(h(1,2))*code(2,:))*inoise'
    
   
%******************** BPSK Demodulation *********************

                 demodata=data9 > 0;
    
%******************** Bit Error Rate (BER) ******************
	
    % count number of instantaneous errors
    noe2=sum(abs(data0-demodata));  % sum: built in function
	
    % count number of instantaneous transmitted data
    nod2=length(data);  % length: built in function
	
    noe=noe+noe2;
	nod=nod+nod2;

	%fprintf('%d\t%e\n',iii,noe2/nod2)
end % for iii=1:nloop    

%********************** Output result ***************************

dscdma_open_ber3 = noe/nod;
fprintf('%d\t%d\t%d\t%e\n',snr_in_dB,noe,nod,noe/nod);


%******************** end of file ***************************