NSCRTV-HFCEMS-TVMOD-MIB DEFINITIONS::=BEGIN
   IMPORTS
      OBJECT-TYPE       
         FROM RFC-1212
      DisplayString 
         FROM RFC1213-MIB
      tvmodIdent
         FROM NSCRTV-ROOT
;

tvmodVendorOID OBJECT-TYPE
   SYNTAX OBJECT IDENTIFIER
   ACCESS read-only
   STATUS optional
   DESCRIPTION
"此對象提供廠商對模擬電視調制器MIB的擴充。無擴充時此對象應指向模擬電視調制
器節點tvmodIdent。"
   ::={ tvmodIdent 1 }

tvmodOutputlevel OBJECT-TYPE
   SYNTAX INTEGER ( 0..255 )
   ACCESS read-only
   STATUS mandatory
   DESCRIPTION
"輸出電平，單位為dBuV，此對象要求在屬性MIB中登記一個條目。"
   ::={ tvmodIdent 2 }

tvmodOutputlevelAtt OBJECT-TYPE
   SYNTAX INTEGER ( 0..255 )
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
"衰減量，單位為dB。此對象要求在屬性MIB中登記一個條目。"
   ::={ tvmodIdent 3 }

tvmodAVPower-ratio OBJECT-TYPE
   SYNTAX INTEGER ( -128..127 )
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
"圖象伴音功率比（A/V）,單位為dB。此對象要求在屬性MIB中登記一個條目。"
   ::={ tvmodIdent 4 }

tvmodfreqdeviation OBJECT-TYPE
   SYNTAX INTEGER ( 0..255 )
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
"頻偏，單位為KHz。此對象要求在屬性MIB中登記一個條目。"
   ::={ tvmodIdent 5 }

tvmodOperatingFreq OBJECT-TYPE
   SYNTAX INTEGER
   ACCESS read-only
   STATUS mandatory
   DESCRIPTION
"輸出頻率,單位為Hz。此對象要求在屬性MIB中登記一個條目。"
   ::={ tvmodIdent 6 }

tvmodModulatingDegree OBJECT-TYPE
   SYNTAX INTEGER ( 0..99 )
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
"調制度,單位為1%,‘0’表示：無調制。此對象要求在屬性MIB中登記一個條目。"
   ::={ tvmodIdent 7 }

tvmodLockalarm OBJECT-TYPE
   SYNTAX INTEGER {
      normal (1),
      alarm (2)
      }
   ACCESS read-only
   STATUS mandatory
   DESCRIPTION
"鎖相告警，‘1’為正常，‘2’為告警。此對象要求在屬性MIB中登記一個條目。"
   ::={ tvmodIdent 8 }

--***********
--*直流電源
--***********

tvmodNumberDCPowerSupply OBJECT-TYPE
   SYNTAX INTEGER ( 0..16 )
   ACCESS read-only
   STATUS mandatory
   DESCRIPTION
"內部直流電源的數目，‘0’表示應答器設備不支持無此功能。"
   ::={ tvmodIdent 9 }

tvmodDCPowerSupplymode OBJECT-TYPE
   SYNTAX INTEGER { loadsharing(1),switchedRedundant(2) }
   ACCESS read-only
   STATUS optional
   DESCRIPTION
"直流供電電源工作模式。"
   ::={ tvmodIdent 10 }

tvmodDCPowerTable OBJECT-TYPE
   SYNTAX SEQUENCE OF TvmodDCPowerEntry
   ACCESS not-accessible
   STATUS mandatory
   DESCRIPTION
"直流電源信息表。"
   ::={ tvmodIdent 11 }

tvmodDCPowerEntry OBJECT-TYPE
   SYNTAX TvmodDCPowerEntry
   ACCESS not-accessible
   STATUS mandatory
   DESCRIPTION
"直流電源信息表目。"
   INDEX { tvmodDCPowerIndex }
   ::= { tvmodDCPowerTable 1 }

TvmodDCPowerEntry::=
   SEQUENCE
   {
      tvmodDCPowerIndex
         INTEGER,
      tvmodDCPowerVoltage
         INTEGER,
      tvmodDCPowerCurrent
         INTEGER,
      tvmodDCPowerName
         DisplayString
   }

tvmodDCPowerIndex OBJECT-TYPE
   SYNTAX INTEGER 
   ACCESS read-only
   STATUS mandatory
   DESCRIPTION
"直流電源索引。"
   ::={ tvmodDCPowerEntry 1 }

tvmodDCPowerVoltage OBJECT-TYPE
   SYNTAX INTEGER (-32768..32767)
   ACCESS read-only
   STATUS mandatory
   DESCRIPTION
"直流電源電壓，單位為0.1V。此對象要求在屬性MIB中登記一個條目。"
   ::={ tvmodDCPowerEntry 2 }

tvmodDCPowerCurrent OBJECT-TYPE
   SYNTAX INTEGER (0..65535)
   ACCESS read-only
   STATUS optional
   DESCRIPTION
"電源的電流，單位為0.01A。此對象要求在屬性MIB中登記一個條目。"
   ::={ tvmodDCPowerEntry 3 }

tvmodDCPowerName OBJECT-TYPE
   SYNTAX DisplayString
   ACCESS read-only
   STATUS mandatory
   DESCRIPTION
"標明直流電源名稱，例如：24V直流電源。
此字段值由用戶規定，至少應標明工作電壓并將多個電源相互區分開。
當此表中的對象產生告警時，此對象名稱應放進hfcAlarmEvent陷阱的alarmText對象
里。"
   ::={ tvmodDCPowerEntry 4 }

END