NSCRTV-HFCEMS-QAMMOD-MIB DEFINITIONS::=BEGIN
   IMPORTS
      OBJECT-TYPE       
         FROM RFC-1212
      DisplayString 
         FROM RFC1213-MIB
      qammodIdent
         FROM NSCRTV-ROOT
;
qamMOdVendorOID OBJECT-TYPE
   SYNTAX OBJECT IDENTIFIER
   ACCESS read-only
   STATUS optional
   DESCRIPTION
"此對象提供廠商對QAM調制器MIB的擴充。無擴充時此對象應指向QAM調制器節點"
   ::={ qammodIdent 1 }

qamModmode OBJECT-TYPE
   SYNTAX INTEGER ( 1..6 )
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
"QAM模式,包括16、32、64、128、256、預留,共6種。"
   ::={ qammodIdent 2 }

qamModsymbolrate OBJECT-TYPE
   SYNTAX INTEGER ( 0..65535 )
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
"符號率，正常范圍為1150..7000，單位為ksym/s。此對象要求在屬性MIB中登記一個條
目。"
   ::={ qammodIdent 3 }

qamModRFfreq OBJECT-TYPE
   SYNTAX INTEGER 
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
"RF頻率,單位為Hz。此對象要求在屬性MIB中登記一個條目。"
   ::={ qammodIdent 4 }

qamModRFLevel OBJECT-TYPE
   SYNTAX INTEGER 
   ACCESS read-write
   STATUS optional
   DESCRIPTION
"RF輸出電平，單位為dBuV。此對象要求在屬性MIB中登記一個條目。"
   ::={ qammodIdent 5 }

qamModInputInterface OBJECT-TYPE
   SYNTAX INTEGER {
      asi (1),
      spi (2),
      ds3 (3),
      other (4)
   }
   ACCESS read-only
   STATUS mandatory
   DESCRIPTION
"輸入接口類型有asi、spi、ds3和其它。"
   ::={ qammodIdent 6 }

qamModstatus OBJECT-TYPE
   SYNTAX INTEGER {
sync (1),
nasync (2)
}
   ACCESS read-only
   STATUS mandatory
   DESCRIPTION
"調制狀態有‘1'同步和‘2'不同步兩種。"
   ::={ qammodIdent 7 }

qamModTSpacketlen OBJECT-TYPE
   SYNTAX INTEGER {
      bytes188 (1),
      bytes204 (2)
   }
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
"輸入TS流包長度，‘1'表示188字節，‘2'表示204字節。"
   ::={ qammodIdent 8 }

--***********
--*直流電源
--***********

qamModNumberDCPowerSupply OBJECT-TYPE
   SYNTAX INTEGER ( 0..16 )
   ACCESS read-only
   STATUS mandatory
   DESCRIPTION
"內部直流電源的數目，‘0’表示設備無此功能。"
   ::={ qammodIdent 9 }

qamModDCPowerSupplyMode OBJECT-TYPE
   SYNTAX INTEGER {
loadsharing (1),
switchedRedundant (2),
aloneSupply (3)
}
   ACCESS read-only
   STATUS optional
   DESCRIPTION
"供電電源工作模式。"
   ::={ qammodIdent 10 }

qamModDCPowerTable OBJECT-TYPE 
   SYNTAX SEQUENCE OF QamModDCPowerEntry
   ACCESS not-accessible
   STATUS mandatory
   DESCRIPTION
"直流電源信息表。"
   ::={ qammodIdent 11 }

qamModDCPowerEntry OBJECT-TYPE

   SYNTAX QamModDCPowerEntry
   ACCESS not-accessible
   STATUS mandatory
   DESCRIPTION
"直流電源信息表目。"
   INDEX { qamModDCPowerIndex }
   ::={ qamModDCPowerTable 1 }

qamModDCPowerEntry::=
   SEQUENCE
   {
qamModDCPowerIndex
INTEGER,
qamModDCPowerVoltage
INTEGER,
qamModDCPowerCurrent
INTEGER,
qamModDCPowerName
DisplayString
}

qamModDCPowerIndex OBJECT-TYPE
   SYNTAX INTEGER 
   ACCESS read-only
   STATUS mandatory
   DESCRIPTION
"直流電源索引。"
   ::={ qamModDCPowerEntry 1 }

qamModDCPowerVoltage OBJECT-TYPE
   SYNTAX INTEGER (-32768..32767)
   ACCESS read-only
   STATUS mandatory
   DESCRIPTION
"電源電壓，單位為0.1V。此對象要求在屬性MIB中登記一個條目。"
   ::={ qamModDCPowerEntry 2 }

qamModDCPowerCurrent OBJECT-TYPE
   SYNTAX INTEGER (0..65535)
   ACCESS read-only
   STATUS optional
   DESCRIPTION
"電源的電流，單位為0.01A。此對象要求在屬性MIB中登記一個條目。"
   ::={ qamModDCPowerEntry 3 }

qamModDCPowerName OBJECT-TYPE
   SYNTAX DisplayString
   ACCESS read-only
   STATUS mandatory
   DESCRIPTION
"標明電源的名稱，例如：24V直流電源。
此字段值由用戶規定，至少應標明工作電壓并將多個電源相互區分開。
當這張表里的對象產生告警時，此對象名稱應放進hfcAlarmEvent陷阱的alarmText對象
里。"
   ::={ qamModDCPowerEntry 4 }

END