# Hey Emacs, this is a -*- makefile -*-#----------------------------------------------------------------------------# WinAVR Makefile Template written by Eric B. Weddington, J鰎g Wunsch, et al.## Released to the Public Domain## Additional material for this makefile was written by:# Peter Fleury# Tim Henigan# Colin O'Flynn# Reiner Patommel# Markus Pfaff# Sander Pool# Frederik Rouleau##----------------------------------------------------------------------------# On command line:## make all = Make software.## make clean = Clean out built project files.## make coff = Convert ELF to AVR COFF.## make extcoff = Convert ELF to AVR Extended COFF.## make program = Download the hex file to the device, using avrdude.#                Please customize the avrdude settings below first!## make debug = Start either simulavr or avarice as specified for debugging, #              with avr-gdb or avr-insight as the front end for debugging.## make filename.s = Just compile filename.c into the assembler code only.## make filename.i = Create a preprocessed source file for use in submitting#                   bug reports to the GCC project.## To rebuild project do "make clean" then "make all".#----------------------------------------------------------------------------# MCU nameMCU = atmega169# Processor frequency.#     This will define a symbol, F_CPU, in all source code files equal to the #     processor frequency. You can then use this symbol in your source code to #     calculate timings. Do NOT tack on a 'UL' at the end, this will be done#     automatically to create a 32-bit value in your source code.F_CPU = 8000000# Output format. (can be srec, ihex, binary)FORMAT = ihex# Target file name (without extension).TARGET = main#default to NOKIA LCD ?= NOKIA# List C source files here. (C dependencies are automatically generated.)SRC = vs1001.c delay.c uart.c  button.c SRC += timer0.cSRC += eeprom.cSRC += power.cSRC += BCD.cSRC += utils.c#SRC += ADC.c # include for MMC HWSRC +=  mmc.c#include for FAT16SRC += avrfat16.c# include only for NOKIA buildsifeq ($(LCD),NOKIA)	SRC += pcd8544.c lcdgraphics.c endif#include for ALPHA buildsifeq ($(LCD),ALPHA)	SRC += LCD_functions.c LCD_driver.c lcdgraphics.c endif#include for NO_DISPLAY buildsifeq ($(LCD),NO_DISPLAY)	SRC += lcdgraphics.c endifSRC += $(TARGET).c# List Assembler source files here.#     Make them always end in a capital .S.  Files ending in a lowercase .s#     will not be considered source files but generated files (assembler#     output from the compiler), and will be deleted upon "make clean"!#     Even though the DOS/Win* filesystem matches both .s and .S the same,#     it will preserve the spelling of the filenames, and gcc itself does#     care about how the name is spelled on its command-line.ASRC = # Optimization level, can be [0, 1, 2, 3, s]. #     0 = turn off optimization. s = optimize for size.#     (Note: 3 is not always the best optimization level. See avr-libc FAQ.)OPT = s# Debugging format.#     Native formats for AVR-GCC's -g are dwarf-2 [default] or stabs.#     AVR Studio 4.10 requires dwarf-2.#     AVR [Extended] COFF format requires stabs, plus an avr-objcopy run.DEBUG = stabs# List any extra directories to look for include files here.#     Each directory must be seperated by a space.#     Use forward slashes for directory separators.#     For a directory that has spaces, enclose it in quotes.EXTRAINCDIRS = # Compiler flag to set the C Standard level.#     c89   = "ANSI" C#     gnu89 = c89 plus GCC extensions#     c99   = ISO C99 standard (not yet fully implemented)#     gnu99 = c99 plus GCC extensionsCSTANDARD = -std=gnu99# Place -D or -U options hereCDEFS = -DF_CPU=$(F_CPU)UL -D$(LCD)# Place -I options hereCINCS =#---------------- Compiler Options ----------------#  -g*:          generate debugging information#  -O*:          optimization level#  -f...:        tuning, see GCC manual and avr-libc documentation#  -Wall...:     warning level#  -Wa,...:      tell GCC to pass this to the assembler.#    -adhlns...: create assembler listingCFLAGS = -g$(DEBUG)CFLAGS += $(CDEFS) $(CINCS)CFLAGS += -O$(OPT)CFLAGS += -funsigned-char -funsigned-bitfields -fpack-struct -fshort-enumsCFLAGS += -Wall -Wstrict-prototypesCFLAGS += -Wa,-adhlns=$(<:.c=.lst)CFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))CFLAGS += $(CSTANDARD)#---------------- Assembler Options ----------------#  -Wa,...:   tell GCC to pass this to the assembler.#  -ahlms:    create listing#  -gstabs:   have the assembler create line number information; note that#             for use in COFF files, additional information about filenames#             and function names needs to be present in the assembler source#             files -- see avr-libc docs [FIXME: not yet described there]ASFLAGS = -Wa,-adhlns=$(<:.S=.lst),-gstabs #---------------- Library Options ----------------# Minimalistic printf versionPRINTF_LIB_MIN = -Wl,-u,vfprintf -lprintf_min# Floating point printf version (requires MATH_LIB = -lm below)PRINTF_LIB_FLOAT = -Wl,-u,vfprintf -lprintf_flt# If this is left blank, then it will use the Standard printf version.PRINTF_LIB = #PRINTF_LIB = $(PRINTF_LIB_MIN)#PRINTF_LIB = $(PRINTF_LIB_FLOAT)# Minimalistic scanf versionSCANF_LIB_MIN = -Wl,-u,vfscanf -lscanf_min# Floating point + %[ scanf version (requires MATH_LIB = -lm below)SCANF_LIB_FLOAT = -Wl,-u,vfscanf -lscanf_flt# If this is left blank, then it will use the Standard scanf version.SCANF_LIB = #SCANF_LIB = $(SCANF_LIB_MIN)#SCANF_LIB = $(SCANF_LIB_FLOAT)MATH_LIB =#MATH_LIB = -lm#---------------- External Memory Options ----------------# 64 KB of external RAM, starting after internal RAM (ATmega128!),# used for variables (.data/.bss) and heap (malloc()).#EXTMEMOPTS = -Wl,-Tdata=0x801100,--defsym=__heap_end=0x80ffff# 64 KB of external RAM, starting after internal RAM (ATmega128!),# only used for heap (malloc()).#EXTMEMOPTS = -Wl,--defsym=__heap_start=0x801100,--defsym=__heap_end=0x80ffffEXTMEMOPTS =#---------------- Linker Options ----------------#  -Wl,...:     tell GCC to pass this to linker.#    -Map:      create map file#    --cref:    add cross reference to  map fileLDFLAGS = -Wl,-Map=$(TARGET).map,--crefLDFLAGS += $(EXTMEMOPTS)LDFLAGS += $(PRINTF_LIB) $(SCANF_LIB) $(MATH_LIB)#---------------- Programming Options (avrdude) ----------------# Programming hardware: alf avr910 avrisp bascom bsd # dt006 pavr picoweb pony-stk200 sp12 stk200 stk500## Type: avrdude -c ?# to get a full listing.#AVRDUDE_PROGRAMMER = butterfly# com1 = serial port. Use lpt1 to connect to parallel port.AVRDUDE_PORT = /dev/cu.usbserial    # programmer connected to serial deviceAVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep# Uncomment the following if you want avrdude's erase cycle counter.# Note that this counter needs to be initialized first using -Yn,# see avrdude manual.#AVRDUDE_ERASE_COUNTER = -y# Uncomment the following if you do /not/ wish a verification to be# performed after programming the device.#AVRDUDE_NO_VERIFY = -V# Increase verbosity level.  Please use this when submitting bug# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude> # to submit bug reports.#AVRDUDE_VERBOSE = -v -vAVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)#---------------- Debugging Options ----------------# For simulavr only - target MCU frequency.DEBUG_MFREQ = $(F_CPU)# Set the DEBUG_UI to either gdb or insight. DEBUG_UI = gdb#DEBUG_UI = insight# Set the debugging back-end to either avarice, simulavr.DEBUG_BACKEND = avarice#DEBUG_BACKEND = simulavr# GDB Init Filename.GDBINIT_FILE = __avr_gdbinit# When using avarice settings for the JTAGJTAG_DEV = /dev/cu.usbserial#JTAG_OPTS = --erase# Debugging port used to communicate between GDB / avarice / simulavr.DEBUG_PORT = 4242# Debugging host used to communicate between GDB / avarice / simulavr, normally#     just set to localhost unless doing some sort of crazy debugging when #     avarice is running on a different computer.DEBUG_HOST = localhost#============================================================================# Define programs and commands.SHELL = shCC = avr-gccOBJCOPY = avr-objcopyOBJDUMP = avr-objdumpSIZE = avr-sizeNM = avr-nmAVRDUDE = avrdudeREMOVE = rm -fCOPY = cpWINSHELL = cmd# Define Messages# EnglishMSG_ERRORS_NONE = Errors: noneMSG_BEGIN = -------- begin --------MSG_END = --------  end  --------MSG_SIZE_BEFORE = Size before: MSG_SIZE_AFTER = Size after:MSG_COFF = Converting to AVR COFF:MSG_EXTENDED_COFF = Converting to AVR Extended COFF:MSG_FLASH = Creating load file for Flash:MSG_EEPROM = Creating load file for EEPROM:MSG_EXTENDED_LISTING = Creating Extended Listing:MSG_SYMBOL_TABLE = Creating Symbol Table:MSG_LINKING = Linking:MSG_COMPILING = Compiling:MSG_ASSEMBLING = Assembling:MSG_CLEANING = Cleaning project:# Define all object files.OBJ = $(SRC:.c=.o) $(ASRC:.S=.o) # Define all listing files.LST = $(SRC:.c=.lst) $(ASRC:.S=.lst) # Compiler flags to generate dependency files.GENDEPFLAGS = -MD -MP -MF .dep/$(@F).d# Combine all necessary flags and optional flags.# Add target processor to flags.ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS) $(GENDEPFLAGS)ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS)# Default target.all: begin gccversion sizebefore build sizeafter endbuild: elf hex eep lss symelf: $(TARGET).elfhex: $(TARGET).hexeep: $(TARGET).eeplss: $(TARGET).lss sym: $(TARGET).sym# Eye candy.# AVR Studio 3.x does not check make's exit code but relies on# the following magic strings to be generated by the compile job.begin:	@echo	@echo $(MSG_BEGIN)end:	@echo $(MSG_END)	@echo# Display size of file.HEXSIZE = $(SIZE) --target=$(FORMAT) $(TARGET).hexELFSIZE = $(SIZE) -A $(TARGET).elfAVRMEM = avr-mem.sh $(TARGET).elf $(MCU)sizebefore:	@if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_BEFORE); $(ELFSIZE); \	$(AVRMEM) 2>/dev/null; echo; fisizeafter:	@if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_AFTER); $(ELFSIZE); \	$(AVRMEM) 2>/dev/null; echo; fi# Display compiler version information.gccversion : 	@$(CC) --version# Program the device.  program: $(TARGET).hex $(TARGET).eep	$(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)# Generate avr-gdb config/init file which does the following:#     define the reset signal, load the target file, connect to target, and set #     a breakpoint at main().gdb-config: 	@$(REMOVE) $(GDBINIT_FILE)	@echo define reset >> $(GDBINIT_FILE)	@echo SIGNAL SIGHUP >> $(GDBINIT_FILE)	@echo end >> $(GDBINIT_FILE)	@echo file $(TARGET).elf >> $(GDBINIT_FILE)	@echo target remote $(DEBUG_HOST):$(DEBUG_PORT)  >> $(GDBINIT_FILE)ifeq ($(DEBUG_BACKEND),simulavr)	@echo load  >> $(GDBINIT_FILE)endif		@echo break main >> $(GDBINIT_FILE)	debug: gdb-config $(TARGET).elfifeq ($(DEBUG_BACKEND), avarice)	@echo Starting AVaRICE - Press enter when "waiting to connect" message displays.#	@$(WINSHELL) /c start avarice --jtag $(JTAG_DEV) --erase --program --file \	$(TARGET).elf $(DEBUG_HOST):$(DEBUG_PORT)#	@$(WINSHELL) /c pause	@avarice --jtag $(JTAG_DEV) $(JTAG_OPTS) --program --file \	$(TARGET).elf $(DEBUG_HOST):$(DEBUG_PORT) &	else	@$(WINSHELL) /c start simulavr --gdbserver --device $(MCU) --clock-freq \	$(DEBUG_MFREQ) --port $(DEBUG_PORT)endif#	@$(WINSHELL) /c start 	sleep 10	avr-$(DEBUG_UI) --command=$(GDBINIT_FILE)	# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB.COFFCONVERT=$(OBJCOPY) --debugging \--change-section-address .data-0x800000 \--change-section-address .bss-0x800000 \--change-section-address .noinit-0x800000 \--change-section-address .eeprom-0x810000 coff: $(TARGET).elf	@echo	@echo $(MSG_COFF) $(TARGET).cof	$(COFFCONVERT) -O coff-avr $< $(TARGET).cofextcoff: $(TARGET).elf	@echo	@echo $(MSG_EXTENDED_COFF) $(TARGET).cof	$(COFFCONVERT) -O coff-ext-avr $< $(TARGET).cof# Create final output files (.hex, .eep) from ELF output file.%.hex: %.elf	@echo	@echo $(MSG_FLASH) $@	$(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@%.eep: %.elf	@echo	@echo $(MSG_EEPROM) $@	-$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \	--change-section-lma .eeprom=0 -O $(FORMAT) $< $@# Create extended listing file from ELF output file.%.lss: %.elf	@echo	@echo $(MSG_EXTENDED_LISTING) $@	$(OBJDUMP) -h -S $< > $@# Create a symbol table from ELF output file.%.sym: %.elf	@echo	@echo $(MSG_SYMBOL_TABLE) $@	$(NM) -n $< > $@# Link: create ELF output file from object files..SECONDARY : $(TARGET).elf.PRECIOUS : $(OBJ)%.elf: $(OBJ)	@echo	@echo $(MSG_LINKING) $@	$(CC) $(ALL_CFLAGS) $^ --output $@ $(LDFLAGS)# Compile: create object files from C source files.%.o : %.c	@echo	@echo $(MSG_COMPILING) $<	$(CC) -c $(ALL_CFLAGS) $< -o $@ # Compile: create assembler files from C source files.%.s : %.c	$(CC) -S $(ALL_CFLAGS) $< -o $@# Assemble: create object files from assembler source files.%.o : %.S	@echo	@echo $(MSG_ASSEMBLING) $<	$(CC) -c $(ALL_ASFLAGS) $< -o $@# Create preprocessed source for use in sending a bug report.%.i : %.c	$(CC) -E -mmcu=$(MCU) -I. $(CFLAGS) $< -o $@ # Target: clean project.clean: begin clean_list endclean_list :	@echo	@echo $(MSG_CLEANING)	$(REMOVE) $(TARGET).hex	$(REMOVE) $(TARGET).eep	$(REMOVE) $(TARGET).cof	$(REMOVE) $(TARGET).elf	$(REMOVE) $(TARGET).map	$(REMOVE) $(TARGET).sym	$(REMOVE) $(TARGET).lss	$(REMOVE) $(OBJ)	$(REMOVE) $(LST)	$(REMOVE) $(SRC:.c=.s)	$(REMOVE) $(SRC:.c=.d)	$(REMOVE) .dep/*# Include the dependency files.-include $(shell mkdir .dep 2>/dev/null) $(wildcard .dep/*)# Listing of phony targets..PHONY : all begin finish end sizebefore sizeafter gccversion \build elf hex eep lss sym coff extcoff \clean clean_list program debug gdb-config