#include "44b.h"
#include "def.h"
#include "option.h"
#include "utils.h"
#include "iic.h"

#define WRDATA	    (1)
#define POLLACK     (2)
#define RDDATA	    (3)
#define SETRDADDR   (4)

#define IICBUFSIZE 0x20

U8 _iicData[IICBUFSIZE];
volatile int _iicDataCount;
volatile int _iicStatus;
volatile int _iicMode;
int _iicPt;

void __irq IicInt(void);

void Test_Iic( void )
{
    unsigned int i,j,save_F,save_PF;
    static U8 data[256];

    printf("\nIIC EEPROM AT24C02 Read and Write Test\n");

    printf("\n\n注意由于本項測試使用了中斷，所以必須將本項目的目標代碼燒寫入Flash的0地址\n");
    printf("這樣Flash中才有中斷向量，不過只需要燒入一次就行了，以后JTAG調試或網口下載運行本程序就沒有問題了\n");
    printf("可以使用netload或者是comload下載本目標代碼到SDRAM，然后用Prog 0燒寫代碼到Flash(不覆蓋0地址跳轉指令)\n\n");

    save_F=rPCONF;
    save_PF=rPUPF;
    rPCONF |=0xa;	//PF0:IICSCL, PF1:IICSDA
    rPUPF |=0x3;	//pull-up disable

    rINTMSK = BIT_GLOBAL ;	//disable INT
	rINTCON = 0x5 ;		//無向量中斷模式
	rINTMOD = 0x0 ;		//All=IRQ mode
    pISR_IIC = (unsigned)IicInt;
    rINTMSK = ~(BIT_GLOBAL|BIT_IIC);

    rIICCON=(1<<7)|(0<<6)|(1<<5)|(0xf);
    //Enable interrupt, IICCLK=MCLK/16, Enable ACK
    //40Mhz/16/(15+1) = 257Khz	
    rIICADD=0x10;   // S3C44B0X slave address

    rIICSTAT=0x10;

    printf("\nWrite test data into KS24C080\n");

    for(i=0;i<256;i++)
	Wr24C040(0xa0,(U8)i,i);
    for(i=0;i<256;i++)
	data[i]=0;

    printf("\nRead test data from KS24C080\n\n");
    for(i=0;i<256;i++)
	Rd24C040(0xa0,(U8)i,&(data[i])); 

    for(i=0;i<16;i++)
    {
		for(j=0;j<16;j++)
		    printf("%2x ",data[i*16+j]);
		printf("\n");
    }
    
    rPCONF=save_F;
    rPUPF=save_PF;
    rINTMSK = BIT_GLOBAL ;	//disable INT
}


void Wr24C040(U32 slvAddr,U32 addr,U8 data)
{
    _iicMode=WRDATA;
    _iicPt=0;
    _iicData[0]=(U8)addr;
    _iicData[1]=data;
    _iicDataCount=2;
    
    rIICDS=slvAddr;//0xa0
    rIICSTAT=0xf0; //MasTx,Start
    //Clearing the pending bit isn't needed because the pending bit has been cleared.
    while(_iicDataCount!=-1);

    _iicMode=POLLACK;

    while(1)
    {
	rIICDS=slvAddr;
	_iicStatus=0x100;
	rIICSTAT=0xf0; //MasTx,Start
	rIICCON=0xaf;  //resumes IIC operation. 
	while(_iicStatus==0x100);
	if(!(_iicStatus&0x1))
	    break; // when ACK is received
    }
    rIICSTAT=0xd0;  //stop MasTx condition 
    rIICCON=0xaf;   //resumes IIC operation. 
    Delay(1);	    //wait until stop condtion is in effect.

    //write is completed.
}
	

void Rd24C040(U32 slvAddr,U32 addr,U8 *data)
{
    _iicMode=SETRDADDR;
    _iicPt=0;
    _iicData[0]=(U8)addr;
    _iicDataCount=1;

    rIICDS=slvAddr;
    rIICSTAT=0xf0; //MasTx,Start  
    //Clearing the pending bit isn't needed because the pending bit has been cleared.
    while(_iicDataCount!=-1);

    _iicMode=RDDATA;

    _iicPt=0;
    _iicDataCount=1;
    
    rIICDS=slvAddr;
    rIICSTAT=0xb0; //MasRx,Start
    rIICCON=0xaf;  //resumes IIC operation.   
    while(_iicDataCount!=-1);

    *data=_iicData[1];
}



void __irq IicInt(void)
{
    U32 iicSt,i;
    rI_ISPC=BIT_IIC;

    iicSt=rIICSTAT; 
    if(iicSt&0x8){} // when bus arbitration is failed.
    if(iicSt&0x4){} // when a slave address is matched with IICADD
    if(iicSt&0x2){} // when a slave address is 0000000b
    if(iicSt&0x1){} // when ACK isn't received

    switch(_iicMode)
    {
	case POLLACK:
	    _iicStatus=iicSt;
	    break;

	case RDDATA:
	    if((_iicDataCount--)==0)
	    {
		_iicData[_iicPt++]=rIICDS;
	    
		rIICSTAT=0x90;  //stop MasRx condition 
		rIICCON=0xaf;   //resumes IIC operation.
		Delay(1);	//wait until stop condtion is in effect.
				//too long time... 
		//The pending bit will not be set after issuing stop condition.
		break;    
	    }	     
	    _iicData[_iicPt++]=rIICDS;
				//The last data has to be read with no ack.
	    if((_iicDataCount)==0)
		rIICCON=0x2f;	//resumes IIC operation with NOACK.  
	    else 
		rIICCON=0xaf;	//resumes IIC operation with ACK
	    break;

	case WRDATA:
	    if((_iicDataCount--)==0)
	    {
		rIICSTAT=0xd0;	//stop MasTx condition 
		rIICCON=0xaf;	//resumes IIC operation.
		Delay(1);	//wait until stop condtion is in effect.
		//The pending bit will not be set after issuing stop condition.
		break;    
	    }
	    rIICDS=_iicData[_iicPt++];  //_iicData[0] has dummy.
	    for(i=0;i<10;i++);	    //for setup time until rising edge of IICSCL
	    rIICCON=0xaf;	    //resumes IIC operation.
	    break;

	case SETRDADDR:
	    //printf("[S%d]",_iicDataCount);
	    if((_iicDataCount--)==0)
	    {
		break;  //IIC operation is stopped because of IICCON[4]    
	    }
	    rIICDS=_iicData[_iicPt++];
	    for(i=0;i<10;i++);  //for setup time until rising edge of IICSCL
	    rIICCON=0xaf;	    //resumes IIC operation.
	    break;

	default:
	    break;	  
    }
}