void Uart1_TxInt(void)
{
//    rI_ISPC=BIT_UTXD1;

    if(*uart1TxStr != '\0')
    {
	WrUTXH1(*uart1TxStr++);
	rI_ISPC=BIT_UTXD1;
    }
    else
    {
	rUCON1 &= 0x3f3;//workaround
	rI_ISPC=BIT_UTXD1;
	rINTMSK|=BIT_UTXD1;
    }
}

////////Auto Flow Control TEST(Tx)////////////////

volatile unsigned char * volatile tx0,* tx1,*tx2,tx_end=0;
volatile int i;
volatile int tx_cnt=0;
void Test_UartAFC_Tx(void)
{
    tx_cnt=0;

    tx0=(unsigned char *)malloc(AFC_BUFLEN);
    tx1=tx0;
    tx2=tx0;
    uart_printf("!!!tx0=0x%x\n",tx0);

    for(i=0;i<AFC_BUFLEN;i++)
	*tx1++=i;

    pISR_UTXD1=(unsigned)U1AFC_TxInt;

    
    uart_printf("[UART AFC Tx Test]\n");
    uart_printf("This test should be configured two boards.\n");
    uart_printf("Connect twisted(rx/tx, nCTS/nRTS) cable com2 to other board's com1 port.\n");
    uart_printf("Start Rx first and press any key and,.\n");
    Uart_TxEmpty(0);
    Uart_Getch();

    rUCON1=(1<<9)|(0<<8)|(0<<7)|(0<<6)|(0<<5)|(0<<4)|(1<<2)|(1);
    rUFCON1=0x0;    //FIFO disable
    rUMCON1=0x10;   //Uart1 AFC enable

    uart_printf("Now... Tx with AFC\n");
    Uart_TxEmpty(0);
    rINTMSK=~(BIT_GLOBAL|BIT_UTXD1);

    while(!tx_end);

    uart_printf("\nEnd Tx, transfer data count=%d\n",tx_cnt);

    free((void *)tx0);
    tx_end=0;
    tx_cnt=0;
}

void U1AFC_TxInt(void)
{
    if(tx_cnt < (AFC_BUFLEN))
    {
	uart_printf("%d,",*tx2);
	WrUTXH1(*tx2++);
	rI_ISPC=BIT_UTXD1;
	tx_cnt++;
    }
    else
    {
	Uart_TxEmpty(1);
	rUCON1 &= 0x3f3;//workaround
	rI_ISPC=BIT_UTXD1;
	rINTMSK|=BIT_UTXD1;
	tx_end=1;
    }
}


////////Auto Flow Control TEST(Rx with FIFO)////////////////

volatile unsigned char *rx0,*rx1,*rx2,rx_end=0;
volatile int rx_cnt=0;

void Test_UartAFC_Rx(void)
{
    unsigned int i;
    unsigned int err_cnt=0;


    uart_printf("[UART AFC Rx Test]\n");
    uart_printf("This test should be configured two boards.\n");
    uart_printf("Connect twisted(rx/tx, nCTS/nRTS) cable com1 to other board's com2 port.\n");
    uart_printf("Then, change connected cable between host and com1, host to com2.\n");
    uart_printf("Press any key to com2 and start Rx first.\n");
    Uart_TxEmpty(0);

    Uart_Select(1);
    Uart_Getch();
    
    rx0=(unsigned char *)malloc(AFC_BUFLEN);
    rx1=rx0;
    rx2=rx0;

    pISR_URXD0=(unsigned)U0AFC_RxInt;
    pISR_UERR01=(unsigned)U0AFC_RxErrorInt;

    rx_end=0;

    rUMCON0=0x10;   //Uart0 AFC enable
    rUCON0=(1<<9)|(0<<8)|(1<<7)|(1<<6)|(0<<5)|(0<<4)|(1<<2)|(1);
    rUFCON0=(2<<6)|(1<<4)|(1<<2)|(1<<1)|(1);


    uart_printf("Now... Rx with AFC\n");
    Uart_TxEmpty(1);

    rINTMSK=~(BIT_GLOBAL|BIT_URXD0|BIT_UERR01);

    while(!rx_end);
    delay(1000);

    rINTMSK|=BIT_GLOBAL;

    uart_printf("\nEnd Rx, receive data count=%d\n",rx_cnt);
    uart_printf("Now, change connected cable between host and com2, host to com1.\n");
    uart_printf("Then, press any key.\n");
    Uart_Init(0,115200);
    Uart_Select(0);
    Uart_Getch();

    for(i=0;i<AFC_BUFLEN;i++)
    {
	if(i-(*rx1++))
	{
	    uart_printf("i=%d\n",i);
	    err_cnt++;
	}
    }
    if(err_cnt)
	uart_printf("AFC test fail!! Error count=%d\n",err_cnt);
    else
	uart_printf("AFC test is good!!\n");

    free((void *)rx0);
    rx_end=0;
    rx_cnt=0;
}


void U0AFC_RxInt(void)
{
    rI_ISPC=BIT_URXD0;

    while( (rUFSTAT0 & 0x100) || ((rUFSTAT0 & 0xf) >0) )
    {
	delay(1000);
	*rx2++=rURXH0;
	uart_printf("%d,",*(rx2-1));
	rx_cnt++;
    }
    if(rx_cnt == (AFC_BUFLEN))
        rx_end=1;
}


void U0AFC_RxErrorInt(void)
{
    rI_ISPC=BIT_UERR01;

    switch(rUERSTAT0)//to clear and check the status of register bits
    {
	case 1:
	    WrUTXH1('!');
	    break;
	case 2:
	    WrUTXH1('#');
	    break;
	case 4:
	    WrUTXH1('$');
	    break;
	case 8:
	    WrUTXH1('@');
	    break;
	default :
	    WrUTXH1('*');
	    break;
    }
}


char _done=0, error=0;
void Test_BDMA(void)
{
    char *_buf,i;
    char *_temp2;
    int *_temp;

    _buf=(char *)malloc(100);
    _temp=(int *)malloc(1);
    _temp2=_buf;


    rINTMSK=~(BIT_GLOBAL|BIT_BDMA0|BIT_UERR01);
    pISR_BDMA0=(unsigned)Test_Done;
    pISR_UERR01=(unsigned)Error;
    Uart_Init(0,115200);    
    uart_printf("[Read BDCON0 register in Rxing...]\n");
    Uart_TxEmpty(0);

    rBDISRC0=(0<<30)+(3<<28)+(int)URXH0;    //byte,inc,Rx-buf
    rBDIDES0=(1<<31)+(1<<28)+(int)_buf;	    //M2IO,fix,IISFIF
    rBDICNT0=(1<<31)+(1<<26)+(3<<22)+(1<<21)+(1<<20)+700;
    //Uart0,reserve,done_int,auto-reload/start,DMA enable,COUNT
    rBDCON0 = 0x0<<2;

    rUCON0=0x2c6;	//tx:polling rx:BDMA0    

    while(!_done)
    {
	*_temp=rBDCON0;
	if((rBDCON0 & 0xf))
	{
	    uart_printf("!!Error0x%x!!,",rBDCON0);
	    break;
	}
    }
    uart_printf("!END!\n");

    if(error)
	uart_printf("[rUERSTAT=0x%x]\n",rUERSTAT0);

    rINTMSK|=BIT_GLOBAL;
//    rUCON0 &= 0x3fd;//Rx disable
    rBDICNT0=0x0;   //BDMA stop

    for(i=0;i<10;i++)
	uart_printf("%d=0x%x,",i,*_temp2++);
    uart_printf("\n0x%x,",*_temp);

    free(_buf);
    _done=0;
}

void Test_Done(void)
{
    rI_ISPC=BIT_BDMA0;	//clear pending bit
    _done=1;
}

void Error(void)
{
    rI_ISPC=BIT_UERR01;
    error=1;
}


////////////IrDA////////////

void U1IrDA_TxInt(void)
{
    if(tx_cnt < (IrDA_BUFLEN))
    {
	uart_printf("%d,",*tx2);
	WrUTXH1(*tx2++);
	rI_ISPC=BIT_UTXD1;
	tx_cnt++;
    }
    else
    {
	Uart_TxEmpty(1);
	rUCON1 &= 0x3f3;//workaround
	rI_ISPC=BIT_UTXD1;
	rINTMSK|=BIT_UTXD1;
	tx_end=1;
    }
}


void U1IrDA_RxInt(void)
{
    rI_ISPC=BIT_URXD1;

    while( (rUFSTAT1 & 0x100) || ((rUFSTAT1 & 0xf) >0) )
    {
	*rx2=rURXH1;
	uart_printf("%d,",*rx2++);
	rx_cnt++;
    }
    if(rx_cnt == (IrDA_BUFLEN))
    {
    	rINTMSK|=BIT_URXD1;
        rx_end=1;
    }
}


void U1IrDA_RxErrorInt(void)
{
    rI_ISPC=BIT_UERR01;

    switch(rUERSTAT1)//to clear and check the status of register bits
    {
	case 1:
	    WrUTXH0('!');
	    break;
	case 2:
	    WrUTXH0('#');
	    break;
	case 4:
	    WrUTXH0('$');
	    break;
	case 8:
	    WrUTXH0('@');
	    break;
	default :
	    WrUTXH0('*');
	    break;
    }
}


void Test_Uart1IrDA_Tx(void)
{
    int i, j;
    tx_cnt=0;
    tx0=(unsigned char *)malloc(IrDA_BUFLEN);
    tx1=tx0;
    tx2=tx0;
    uart_printf("!!!tx0=0x%x\n",tx0);
    
    Uart_Select(0);
    
    for(i=0;i<IrDA_BUFLEN;i++)
	*tx1++=i;
        
    pISR_UTXD1=(unsigned)U1IrDA_TxInt;
    
    uart_printf("\nSelect the baud rate\n");
    uart_printf("1)9600    2)19200    3)38400    4)57600    5)115200\n"); 
    j=Uart_Getch();
    switch(j)
    {
	case '1':
            IrDA_BAUD=9600;
        break;
	
	case '2':
            IrDA_BAUD=19200;
        break;
	
	case '3':
            IrDA_BAUD=38400;
        break;
	
	case '4':
            IrDA_BAUD=57600;
        break;
	
	case '5':
            IrDA_BAUD=115200;
        break;
	
	default:
	break;
    }

    rUBRDIV1=( (int)(MCLK/16./IrDA_BAUD + 0.5) -1 );
    uart_printf("rUBRDIV1=%d\n", rUBRDIV1);

    rULCON1=(1<<6)|3;
    rUCON1=0;

    uart_printf("[UART IrDA Tx Test]\n");
    uart_printf("This test should be configured two boards.\n");
    uart_printf("Start Rx first and press any key and...\n");
    Uart_TxEmpty(0);
    Uart_Getch();

    
    rUCON1=(1<<9)|(1<<8)|(0<<7)|(0<<6)|(0<<5)|(0<<4)|(1<<2)|(1);
    //Tx&Rx:Level,Timeout off,Rx err off,Loop-back off,send break off,int,int
    rUFCON1=(1<<6)|(1<<4)|(1<<2)|(1<<1)|(0);	
    uart_printf("Now... Tx with IrDA\n");
    Uart_TxEmpty(0);
    rINTMSK=~(BIT_GLOBAL|BIT_UTXD1);

    while(!tx_end);
    uart_printf("\nEnd Tx, transfer data count=%d\n",tx_cnt);
    while(rUFSTAT1 & 0x2f0);
    Uart_TxEmpty(1);    
  
    uart_printf("\nTx is Done. Press any key to quit!!!\n");
    Uart_Getch();
    Uart_Init(0,115200);
 
}

void Test_Uart1IrDA_Rx(void)
{
    unsigned int i, j, err_cnt;
    rx2=(unsigned char *)malloc(IrDA_BUFLEN);
    rx1=rx2;   
    Uart_Select(0);
        
    pISR_URXD1=(unsigned)U1IrDA_RxInt;
    pISR_UERR01=(unsigned)U1IrDA_RxErrorInt;

    uart_printf("\nSelect the baud rate\n");
    uart_printf("1)9600    2)19200    3)38400    4)57600    5)115200\n"); 
    j=Uart_Getch();
    switch(j)
    {
	case '1':
            IrDA_BAUD=9600;
        break;
	
	case '2':
            IrDA_BAUD=19200;
        break;
	
	case '3':
            IrDA_BAUD=38400;
        break;
	
	case '4':
            IrDA_BAUD=57600;
        break;
	
	case '5':
            IrDA_BAUD=115200;
        break;
	
	default:
	break;
    }

    rUBRDIV1=( (int)(MCLK/16./IrDA_BAUD + 0.5) -1 );
    uart_printf("rUBRDIV1=%d\n", rUBRDIV1);
    
    rUCON1=0;
    rULCON1=(1<<6)|3;

    uart_printf("[UART IrDA Rx Test]\n");
    uart_printf("This test should be configured two boards.\n");
    uart_printf("Press any key to start Rx and then Start Tx....\n");
    Uart_Getch();

    rUCON1=(1<<9)|(1<<8)|(1<<7)|(1<<6)|(0<<5)|(0<<4)|(1<<2)|(1);
//    rUFCON1=0;	//FIFO Disable
    rUFCON1=(2<<6)|(1<<4)|(1<<2)|(1<<1)|(1);	//FIFO Enable
    rx_end=0;
    err_cnt=0;
    uart_printf("Now... Rx with IrDA\n");
    Uart_TxEmpty(0);
     rINTMSK=~(BIT_GLOBAL|BIT_URXD1|BIT_UERR01);

    while(!rx_end);
  
    uart_printf("\nEnd Rx, receive data count=%d\n",rx_cnt);
    
    for(i=0;i<IrDA_BUFLEN;i++)
    {

	if(i-(*rx1++))
	{
	    uart_printf("i=%d\n",i);
	    err_cnt++;
	}
    }
    if(err_cnt)
	uart_printf("IrDA test fail!! Error count=%d\n",err_cnt);
    else
	uart_printf("IrDA test is good!!\n");


    Uart_Init(1,115200);   
    Uart_Init(0,115200);

}