;
; VAG-COM Measuring Block Labels file.
; Module 1 -- Engine
; 
; from USA 2001 Audi allroad quattro 2.7T biturbo (Tiptronic)
;
; ECU p/n  :  4Z7-907-551-K
; Component:  2.7l V6/5VT G 0001
; Soft Coding: 06752
;
; **Modification history**
; created:  Paul Cunningham, 4 June 2001
; please email any comments or corrections: cunningham64@home.com
;
;   Based on USA 2000 S4 2.7T Tiptronic
;   Thanks to Paolo Sechi, USA 1998 Audi A4 2.8L/5V
;   Thanks to Andrew Smith, (gti20v@yahoo.com) 5-speed VW Golf/Jetta 1.8T
;
;
;  DISREGARD OR CONFIRM ANY STATED VALUES
;  Bentley references are for A4/S4
;
;
;2,0,Group Heading: One Line, Maximum 70 Characters!
;2,1,123456789012345,ABCDEFGHIJKLM
;2,2,Max field leng., is 13-17 chars
;2,3,Depends on size, of characters
;2,4,ABCDEFGHIJKLM,abcdefghijklmnopq 
;
; **********************************************************************
; Group 0 labels don't display (yet?) -- included for completeness
;0,0,Engine Status
;0,1,ECT,170-204
;0,2,Load,20-50
;0,3,RPM,62-86
;0,4,T-ang,0-12
;0,5,I-air,118-138
;0,6,I-lrn,118-138
;0,7,O2S1,77-179
;0,8,O2S2,77-179
;0,9,IO2S1,115-141
;0,10,IO2S2,115-141
;
1,0,Engine Idle Speed (specified values listed)
1,1,Engine speed,
1,2,Coolant Temp,80-105C
1,3,O2 Sens Bank1,+/-10%(>2% flct)
1,4,O2 Sens Bank2,+/-10%(>2% flct)
;
2,0,Load Measurement (specified values for idle/2520 RPM)
2,1,Engine speed
2,2,Engine load
2,3,Injection time,2-5/1.6-5ms
2,4,Mass air flow,2.8-5.6/10-15g/s
;
3,0,Throttle Position Sensor check (ign on && eng off -> monitor angle as varied)
3,1,Engine speed
3,2,Mass air flow,g/s
3,3,Throttle angle,0-5deg=closed
3,4,Ign timing,deg
;
4,0,General Engine Data
4,1,Engine speed
4,2,Battery voltage,10-14.5V
4,3,Coolant temp
4,4,Intake air temp
;
5,0,Engine operating conditions (engine oil temp >80C)
5,1,Engine speed
5,2,Engine load
5,3,Vehicle speed,km/h
5,4,Op condition,idl/prt/fl/dcl/erch
;
6,0,General Engine
6,1,Engine speed
6,2,Engine load
6,3,Intake air temp
6,4,Altitud Corr Factr,-50-20%
;
;8 is not found in S4
8,0, Unknown (non-S4) not the hydraulic susp.
8,1,,"not operating"
8,2,,"Pump OFF"
8,3,,"670/365 mbar"
8,4,,Diag status
;
10,0,General Engine
10,1,Engine speed
10,2,Engine load
10,3,Throttle Drive
10,4,Ignition time
;
11,0,General Engine
11,1,Engine speed
11,2,Coolant temp
11,3,Intake air temp
11,4,Ignition time
;
14,0,Misfire recognition (@idle)
14,1,Engine speed
14,2,Engine load
14,3,Total misfires,0-30
14,4,Misfire status,activated
;
15,0,Misfire recognition cylinders 1-3 (@idle)
15,1,Cyl 1,0-5
15,2,Cyl 2,0-5
15,3,Cyl 3,0-5
15,4,Misfire status,activated
;
16,0,Misfire recognition cylinders 4-6 (@idle)
16,1,Cyl 4,0-5
16,2,Cyl 5,0-5
16,3,Cyl 6,0-5
16,4,Misfire status,activated
;
18,0,Misfires
18,1,Lowest engine,speed@misfire
18,2,Highest engine,speed@misfire
18,3,Lowest engine,load@misfire
18,4,Highest engine,load@misfire
;
20,0,Timing correction
20,1,Cyl 1
20,2,Cyl 2
20,3,Cyl 3
20,4,Cyl 4
;
21,0,More Timing correction
21,1,Cyl 5
21,2,Cyl 6
21,3,(no data)
21,4,(no data)
;
22,0,Knock control Cyl 1&&2 (must road test: RPM>2600 && load>3ms)
22,1,Engine speed
22,2,Engine load
22,3,Ign ang corr 1,0-10 deg
22,4,Ign ang corr 2,0-10 deg
;
23,0,Knock control Cyl 3&&4 (must road test: RPM>2600 && load>3ms)
23,1,Engine speed
23,2,Engine load
23,3,Ign ang corr 3,0-10 deg
23,4,Ign ang corr 4,0-10 deg
;
24,0,Knock control Cyl 5&&6 (must road test: RPM>2600 && load>3ms)
24,1,Engine speed
24,2,Engine load
24,3,Ign ang corr 5,0-10 deg
24,4,Ign ang corr 6,0-10 deg
;
26,0,Knock sensor voltage
26,1,Cyl 1
26,2,Cyl 2
26,3,Cyl 3
26,4,Cyl 4
;
27,0,knock sensor voltage
27,1,Cyl 5
27,2,Cyl 6
27,3,(no data)
27,4,(no data)
;
28,0,Undocumented
28,1,Engine speed
28,2,Engine load
28,3,Coolant temp
28,4,Test status
;
30,0,O2S ctrl op. condition [B=Bank S=Sensor]   Fields:[heater on][oper.][ctrl active]
30,1,Status B1S1,000=OK ?
30,2,Status B1S2,000=OK ?
30,3,Status B2S1,000=OK ?
30,4,Status B2S2,000=OK ?
;
31,0,Undocumented
31,1,O2S volts pre TWC
31,2,O2S volts post TWC
31,3,b2 pre TWC
31,4,b2 post TWC
;
32,0,O2S control learning values (before Cat. Conv.)   [B=Bank S=Sensor]
32,1,@idle B1S1,+/-10%
32,2,@part B1S1,+/-10%
32,3,@idle B2S1,+/-10%
32,4,@part B2S1,+/-10%
;
33,0,O2S control (before Cat. Conv.)    [B=Bank S=Sensor]
33,1,Control B1S1,+/-10%(>2% flct)
33,2,Voltage B1S1,0-1V(>0.3V@30Hz)
33,3,Control B2S1,+/-10%(>2% flct)
33,4,Voltage B1S1,0-1V(>0.3V@30Hz)
;
34,0,O2S aging B1S1 (Temp >80C && engine 1800-2200 RPM until "OK")(Bentley 01-123)
34,1,Engine RPM
34,2,Catalyst?
34,3,Time Period,0.2-2.1s
34,4,Diag Status,ON/OFF|OK
;
35,0,O2S aging B2S1 (Temp >80C && engine 1800-2200 RPM until "OK")(Bentley 01-124)
35,1,Engine RPM
35,2,Catalyst?
35,3,Time Period,0.2-2.1s
35,4,Diag Status,ON/OFF|OK
;
36,0,O2S (beyond Cat. Conv.) [B=Bank S=Sensor] (Bentley 01-126)
36,1,Volt Supply B1S2,0-1V
36,2,Diag Status B1S2,ON/OFF|OK
36,3,Volt Supply B2S2,0-1V
36,4,Diag Status B2S2,ON/OFF|OK
;
37,0,[for 2.7T] Diag O2S ctrl Bank 1 (road test >10 min) (Bentley 01-128)
37,1,Engine load
37,2,O2S Volt S2,0-1V
37,3,Corr val S1-S2,-500-500ms
37,4,Diag Status,ON/OFF|OK
;
38,0,[for 2.7T] Diag O2S ctrl Bank 2 (road test >10 min) (Bentley 01-129)
38,1,Engine load
38,2,O2S Volt S2,0-1V
38,3,Corr val S1-S2,-500-500ms
38,4,Diag Status,ON/OFF|OK
;
;39 not found on S4
39,0,Undocumented
39,1,,Mass Flow
39,2,,Voltage
39,3,,Voltage
39,4,,Diag status, ON/OFF|OFF
;
43,0,Oxy sensor aging oxygen sensor behind TWC (bank 1) (Bentley 01-131)
43,1,Engine speed	
43,2,Catalyst?	
43,3,V of O2 sensor,behind TWC (bank 1)	
43,4,Diag status
;
44,0,Oxy sensor aging oxygen sensor behind TWC (bank 2) (Bentley 01-131)
44,1,Engine speed	
44,2,,Catalyst?	
44,3,V of O2 sensor,behind TWC (bank 2)	
44,4,Diag status
;
46,0,Cat. Conv. B1 diagnosis (1800-2200 RPM until "Cat B1 OK") (Bentley 01-134)
46,1,Engine speed
46,2,Catalyst?
46,3,Test time, 0-60s
46,4,Diag status,ON/OFF|OK
;
47,0,Cat. Conv. B2 diagnosis (1800-2200 RPM until "Cat B2 OK") (Bentley 01-135)
47,1,Engine speed
47,2,Catalyst?
47,3,Test time, 0-60
47,4,Diag status,ON/OFF|OK
;
50,0,Signals to Engine Control Module (@idle)
50,1,Engine speed
50,2,Spec'd eng spd
50,3,A/C idle boost
50,4,A/C compressor,ON/OFF
;
51,0,Undocumented
51,1,Engine speed
51,2,Spec'd eng spd
51,3,,Count (0)
51,4,,Voltage
;
53,0,Undocumented
53,1,Engine speed
53,2,Spec'd eng spd
53,3,,Voltage
53,4,,Load
;
54,0,Throttle Position at Speed (700-2520 RPM)
54,1,Engine speed
54,2,Op condition,Idle|Part|
54,3,Throt Position,0-100%
54,4,Throt Drive,0-100%
;
55,0,Idle control (@idle)
55,1,Engine speed
55,2,Idle air ctrl?
55,3,Learn value?
55,4,Op condition,00000=OK?
;
56,0,Idle speed stabilization (@idle)
56,1,Engine speed
56,2,Spec'd RPM
56,3,Ctrl Torque Chg,%
56,4,Op condition,00000=OK
;
60,0,Adaptation of throttle valve control mod.(ign on && engine off) (Bentley 01-111)
60,1,Throt Sens 1,3-93%
60,2,Throt Sens 2,97-3%
60,3,
60,4,Adapt status,RUN/OK/ERROR
;
; 61,62,66 from 1.8T
;
61,0,Throttle
61,1,Engine Speed
61,2,Throt Voltage,12-15V
61,3,Throt Drive,0-100%
61,4,Op condition
;
62,0,Ignition on but engine not running
62,1,Throt Sens 1,3-93%
62,2,Throt Sens 2,97-3%
62,3,Throttle Pos,12-97%
62,4,Sender 2 TPS,4-49%
;
63,0,Ignition on but engine not running
63,1,Throttle Pos,12-97%
63,2,,Duty cycle
63,3,,(no data)
63,4,Adapt status,RUN/OK/ERR
;
64,0,Undocumented
64,1,,Voltage (<1)
64,2,,Voltage (<5)
64,3,,Voltage (<1)
64,4,,Voltage (<5)
;
66,0,Cruise Control
66,1,Vehicle speed
66,2,Brake Position,1000 binary
66,3,Cruise speed,
66,4,Cruise switches,0000 binary
;
70,0,Evap. emissions canister purge valve diagnosis (@idle)  (Bentley 01-113)
70,1,Purge vlv open,0-93%
70,2,O2S deviation,+/-15%
70,3,Idle air vlv dev,-1 to 0 g/s
70,4,Diag status,ON/OFF|OK
;
71,0,Fuel tank leak detection (@idle)  (Bentley 01-116)
71,1,Reed contact,OPEN
71,2,Error msg,(no data)
71,3,Sys Status,Test/check/end
71,4,Diag Status,TestON/OFF|OK
;
77,0,Diag of secondary air injection sys (bank 1) (Bentley 01-137)
77,1,Engine speed	
77,2,Air mass (g/s)	
77,3,Rel. air mass ,sec. air inj.
77,4,Diag status,ON/OFF|OK
;
78,0,Diag of secondary air injection sys (bank 2) (Bentley 01-138)
78,1,Engine speed	
78,2,Air mass (g/s)	
78,3,Rel. air mass, sec. air inj.
78,4,Diag status,ON/OFF|OK
;
81,0,Unexpected text - VIN plus?
82,0,More text
;
86,0,OBD-II Readiness Code (Bentley 01-101 && 105)
86,1,Readiness Code,00000000=OK
86,2,Cycling flags
86,3,Cycling flags
86,4,Cycling flags
;
87,0,Undocumented
87,1,Ready bits
87,2,Error bits
87,3,Error bits
87,4,Error bits
;
88,0,Undocumented
88,1,,contains data
88,2,,contains data
88,3,,contains data
88,4,,(no data)
;
89,0,Undocumented
89,1,,Count (0)
89,2,,(OK)
;
90,0,Camshaft adjustment (values are for idle && road test: accel in 2nd gear)
90,1,Engine speed
90,2,Adj ON/OFF,idle=OFF/rt=ON
90,3,Adj resp Bank1,-3-6/16-25degKW
90,4,Adj resp Bank2,-3-6/16-25degKW
;
91,0,Camshaft adjustment (Bank 1)
91,1,Engine speed
91,2,,Load
91,3,,Cam Ctrl. ON|OFF
91,4,,Adj resp Bank1
;
92,0,Camshaft adjustment (Bank 2)
92,1,Engine speed
92,2,,Load
92,3,,Cam Ctrl. ON|OFF
92,4,,Adj resp Bank2
;
93,0,Undocumented
93,1,Engine speed
93,2,Engine load
93,3,,Dig. Idle Stab.
93,4,,Dig. Idle Stab.
;
94,0,Undocumented
94,1,Engine speed
94,2,Cam Ctrl. ON|OFF
94,3,Test Status
94,4,Test Status
;
99,0,O2S Control (ON in read mode && OFF for diagnosis in Basic Setting)
99,1,Engine speed,RPM
99,2,Coolant temp,80-110 C
99,3,PreCat O2 Reg,-10-10% 
99,4,O2S control,ON|OFF
;
100,0,Undocumented
100,1,Ready Code,00000000
100,2,Coolant Temp,80-110 C
100,3,Running time
100,4,Diag Status,(10000000)
;
101,0,Undocumented
101,1,Engine speed
101,2,Engine load
101,3,,Avg fuel inject time?
101,4,,0.00 g/s
;
102,0,Undocumented
102,1,Engine speed
102,2,Coolant temp
102,3,Intake air temp
102,4,,inj. on time
;
104,0,Undocumented
104,1,Coolant temp
104,2,,Lambda(-20.3)
104,3,,Lambda (4.7)
104,4,,Lambda 0%
;
107,0,Diagnostic of fuel supply  (Bentley 01-118)
107,1,Engine speed
107,2,O2 Control 1,%
107,3,02 Control 2,%
107,4,Diag. status,Test OFF|
;
110,0,Undocumented
110,1,Engine speed
110,2,Coolant temp
110,3,Avg fuel inject time
110,4,Throttle angle
;
111,0,Undocumented
111,1,,8.6%
111,2,,8.6%
111,3,,14.7%
111,4,,9.0%
;
112,0,Undocumented
112,1,,1035 C
112,2,0%
112,3,,1035 C
112,4,0%
;
; 113-120 from 1.8T
;
113,0,Atmosphere
113,1,Engine speed
113,2,Engine load 
113,3,Throttle Drive,0-100%
113,4,Atmos Press,500-1200 mbar 
;
114,0,Boost Pressure regulation - Eng load  (Bentley 21-18)
;load values in 1-3 can vary by 5% from each other
114,1,Spec'd load, Uncorrected
114,2,Corrected load,
114,3,Engine load
114,4,Wastegate valve,duty cycle
;
115,0,Boost pressure regulation  (Bentley 21-14)
115,1,Engine speed
115,2,Engine load
115,3,Spec'd Boost,990-1800 mbar
115,4,Actual Boost,<=1800 mbar
;
116,0,Boost pressure regulation  (Bentley 21-17)
116,1,Engine speed
116,2,Fuel Corr Factr,0-20%
116,3,,0%
116,4,Air Corr Factr,0-20%
;
;116? From Bentley: If display field 2 indicates a correction factor <0 %, 
;fuel quality is probably incorrect. 
;If display field 3 indicates a correction factor <0 %, 
;coolant temperature is too high (heat warning lamp lit 
;in instrument cluster) or the Engine Control Module is
;
117,0,Boost pressure regulation (Bentley 21-16)
117,1,Engine speed
117,2,Throttle Position,0-100%
117,3,Throttle Drive,0-100%
117,4,Spec. Boost,990-1800 mbar
;
118,0,Boost pressure regulation
118,1,Engine speed
118,2,Intake air temp,<=110 C
118,3,Boost Duty Cycle,0-100% 
118,4,Actual Boost,<=1800 mbar
;
119,0,Boost pressure regulation
119,1,Engine speed,700-6800 RPM
119,2,,Charge Limit %
119,3,Boost Duty Cycle,0-100% 
119,4,Actual Boost,<=1800 mbar
;
120,0,Traction Control (ASR)
120,1,Engine speed
120,2,Spec'd torque,(599.8 Nm)
120,3,Current torque,0-260 Nm
120,4,Status,ON|OFF
;
122,0,Engine torque reduced during shifting (road test)
122,1,Engine speed
122,2,Req. torque,(599.8)
122,3,Act. torque,-100-310Nm
122,4,,[Text 000 120]
;122,4,Timing retard,act/mtr eng
;
125,0,Undocumented, At Idle
125,1,,Transmission 1
;fields 2 and 3 dont exist in S4
125,2,,ABS1
125,3,,Instruments 1
125,4,,(no data)
;
;No data beyond 125 for 2000 S4
;
190,0,Unexpected 10-field data thru 199
;
203,0,Undocumented
203,1,,Engine speed
203,2,,Load
203,3,,Inj. on Time
203,4,,Inj. on Time
;
204,0,Undocumented (see 115)
204,1,Engine speed
204,2,,pressure
204,3,,Spec'd boost
204,4,Actual boost,<=1800 mbar
;
205,0,Undocumented
205,1,Engine speed
205,2,Load
205,3,,Load
205,4,,Lambda
;
206,0,Undocumented
206,1,Engine speed
206,2,Load
206,3,,Lambda(8.6)
206,4,,Lambda(14.7)
;
207,0,Undocumented
207,1,Engine speed
207,2,Load
207,3,,Lambda(9.0)
207,4,,Lambda(8.6)
;
208,0,Undocumented
208,1,Engine speed
208,2,Load
208,3,,Load/lambda?
208,4,,Act boost?
;
209,0,Undocumented
209,1,Engine speed
209,2,Load
209,3,,Timing
209,4,,(00000001)
;
210,0,Undocumented
210,1,Engine speed
210,2,Load
210,3,,Act. boost?
210,4,,Dig. Idle Stab.
;
211,0,Undocumented
211,1,,Mass Flow
211,2,,Mass Flow
211,3,,(unknown)
211.4,,Act. boost?
;
212,0,Undocumented
212,1,,Load
212,2,,Lamdba
212,3,,Lambda
212,4,,Load
;
213,0,Undocumented
213,1,,Load (89.6%)
213,2,,Load
213,3,,Act. boost?
213,4,,Load
;
215,0,Undocumented
215,1,,OK
215,2,,(10s)
215,3,,(2.7s)
215,4,,(0s)
;
216,0,Undocumented Bank 1 see 046
216,1,,(0)
216,2,,(0)
216,3,,(1s)
216,4,Test time,0-60
;
217,0,Undocumented Bank 2 see 047
217,1,,(0)
217,2,,(0)
217,3,,(1s)
217,4,,(0.14)
;
218,0,Undocumented
218,1,Engine speed
218,2,,Lambda/Load?
218,3,,Mass Flow
218,4,Diag status,ON/OFF|OK
;
;is this Bank2?
219,0,Undocumented
219,1,Engine speed
219,1,,Lambda/Load?
219,2,,Mass Flow
219,3,,Diag status,ON/OFF|OK
;
220,0,Undocumented
220,1,Engine speed
220,2,Load
220,3,Load
220,4,,OFF
;
221,0,Undocumented (bank2?)
221,1,Engine speed
221,2,Load
221,3,Load
221,4,,OFF
;
222,0,Undocumented
222,1,Engine speed
222,2,Load
222,3,,Load(0)
222,4,,Load(0)
;
;
;
;no data beyond this block
;
;<end of file>