?? 44binit.s
字號:
GET memcfg.s
;Memory Area
;GCS6 16M 16bit(2MB) DRAM/SDRAM(0xc000000-0xc7fffff)
;APP RAM=0xc000000~0xc1effff
;44BMON RAM=0xc7f0000-0xc7fffff
;STACK =0xc7ffa00
;Interrupt Control
INTPND EQU 0x01e00004
INTMOD EQU 0x01e00008
INTMSK EQU 0x01e0000c
I_ISPR EQU 0x01e00020
I_CMST EQU 0x01e0001c
;Watchdog timer
WTCON EQU 0x01d30000
;Clock Controller
PLLCON EQU 0x01d80000
CLKCON EQU 0x01d80004
LOCKTIME EQU 0x01d8000c
;Memory Controller
REFRESH EQU 0x01c80024
;Pre-defined constants
USERMODE EQU 0x10
FIQMODE EQU 0x11
IRQMODE EQU 0x12
SVCMODE EQU 0x13
ABORTMODE EQU 0x17
UNDEFMODE EQU 0x1b
MODEMASK EQU 0x1f
NOINT EQU 0xc0
;check if tasm.exe is used.
GBLL THUMBCODE
[ {CONFIG} = 16
THUMBCODE SETL {TRUE}
CODE32
THUMBCODE SETL {FALSE}
]
[ THUMBCODE
CODE32 ;for start-up code for Thumb mode
]
MACRO
$HandlerLabel HANDLER $HandleLabel
$HandlerLabel
sub sp,sp,#4 ;decrement sp(to store jump address)
stmfd sp!,{r0} ;PUSH the work register to stack(lr does't push because it return to original address)
ldr r0,=$HandleLabel;load the address of HandleXXX to r0
ldr r0,[r0] ;load the contents(service routine start address) of HandleXXX
str r0,[sp,#4] ;store the contents(ISR) of HandleXXX to stack
ldmfd sp!,{r0,pc} ;POP the work register and pc(jump to ISR)
MEND
AREA Init,CODE,READONLY
IMPORT __use_no_semihosting_swi
ENTRY
b ResetHandler ;for debug
b HandlerUndef ;handlerUndef
b HandlerSWI ;SWI interrupt handler
b HandlerPabort ;handlerPAbort
b HandlerDabort ;handlerDAbort
b . ;handlerReserved
;************************************
b HandlerIRQ
b HandlerFIQ
;***IMPORTANT NOTE***
;If the H/W vectored interrutp mode is enabled, The above two instructions should
;be changed like below, to work-around with H/W bug of S3C44B0X interrupt controller.
; b HandlerIRQ -> subs pc,lr,#4
; b HandlerIRQ -> subs pc,lr,#4
;************************************
VECTOR_BRANCH
ldr pc,=HandlerEINT0 ;mGA 硬件中斷向量表H/W interrupt vector table
ldr pc,=HandlerEINT1 ;
ldr pc,=HandlerEINT2 ;
ldr pc,=HandlerEINT3 ;
ldr pc,=HandlerEINT4567 ;
ldr pc,=HandlerTICK ;mGA
b .
b .
ldr pc,=HandlerZDMA0 ;mGB
ldr pc,=HandlerZDMA1 ;
ldr pc,=HandlerBDMA1 ;
ldr pc,=HandlerWDT ;
ldr pc,=HandlerUERR01 ;mGB
b .
b .
ldr pc,=HandlerTIMER0 ;mGC
ldr pc,=HandlerTIMER1 ;
ldr pc,=HandlerTIMER2 ;
ldr pc,=HandlerTIMER3 ;
ldr pc,=HandlerTIMER4 ;
ldr pc,=HandlerTIMER5 ;mGC
b .
b .
ldr pc,=HandlerURXD0 ;mGD
ldr pc,=HandlerURXD1 ;
ldr pc,=HandlerIIC ;
ldr pc,=HandlerSIO ;
ldr pc,=HandlerUTXD0 ;
ldr pc,=HandlerUTXD1 ;mGD
b .
b .
ldr pc,=HandlerRTC ;mGKA
b . ;
b . ;
b . ;
b . ;
b . ;mGKA
b .
b .
ldr pc,=HandlerADC ;mGKB
b . ;
b . ;
b . ;
b . ;
b . ;mGKB
b .
b .
;0xe0=EnterPWDN
ldr pc,=EnterPWDN
LTORG
HandlerFIQ HANDLER HandleFIQ
HandlerIRQ HANDLER HandleIRQ
HandlerUndef HANDLER HandleUndef
HandlerSWI HANDLER HandleSWI
HandlerDabort HANDLER HandleDabort
HandlerPabort HANDLER HandlePabort
HandlerADC HANDLER HandleADC
HandlerRTC HANDLER HandleRTC
HandlerUTXD1 HANDLER HandleUTXD1
HandlerUTXD0 HANDLER HandleUTXD0
HandlerSIO HANDLER HandleSIO
HandlerIIC HANDLER HandleIIC
HandlerURXD1 HANDLER HandleURXD1
HandlerURXD0 HANDLER HandleURXD0
HandlerTIMER5 HANDLER HandleTIMER5
HandlerTIMER4 HANDLER HandleTIMER4
HandlerTIMER3 HANDLER HandleTIMER3
HandlerTIMER2 HANDLER HandleTIMER2
HandlerTIMER1 HANDLER HandleTIMER1
HandlerTIMER0 HANDLER HandleTIMER0
HandlerUERR01 HANDLER HandleUERR01
HandlerWDT HANDLER HandleWDT
HandlerBDMA1 HANDLER HandleBDMA1
HandlerBDMA0 HANDLER HandleBDMA0
HandlerZDMA1 HANDLER HandleZDMA1
HandlerZDMA0 HANDLER HandleZDMA0
HandlerTICK HANDLER HandleTICK
HandlerEINT4567 HANDLER HandleEINT4567
HandlerEINT3 HANDLER HandleEINT3
HandlerEINT2 HANDLER HandleEINT2
HandlerEINT1 HANDLER HandleEINT1
HandlerEINT0 HANDLER HandleEINT0
;deal with IRQ interrupt
IRQ_Handler
IMPORT ISR_IrqHandler
STMFD sp!, {r0-r12, lr}
BL ISR_IrqHandler
LDMFD sp!, {r0-r12, lr}
SUBS pc, lr, #4
EXPORT IRQ_Handler
;One of the following two routines can be used for non-vectored interrupt.
IsrIRQ ;using I_ISPR register.
sub sp,sp,#4 ;reserved for PC
stmfd sp!,{r8-r9}
;IMPORTANT CAUTION
;if I_ISPC isn't used properly, I_ISPR can be 0 in this routine.
ldr r9,=I_ISPR
ldr r9,[r9]
cmp r9, #0x0 ;If the IDLE mode work-around is used,
;r9 may be 0 sometimes.
beq %F2
mov r8,#0x0
0
movs r9,r9,lsr #1
bcs %F1
add r8,r8,#4
b %B0
1
ldr r9,=HandleADC
add r9,r9,r8
ldr r9,[r9]
str r9,[sp,#8]
ldmfd sp!,{r8-r9,pc}
2
ldmfd sp!,{r8-r9}
add sp,sp,#4
subs pc,lr,#4
;****************************************************
;* START *
;****************************************************
ResetHandler
ldr r0,=WTCON ;watch dog disable
ldr r1,=0x0
str r1,[r0]
ldr r0,=INTMSK
ldr r1,=0x07ffffff ;all interrupt disable
str r1,[r0]
;****************************************************
;* Set clock control registers *
;****************************************************
ldr r0,=LOCKTIME
ldr r1,=800 ; count = t_lock * Fin (t_lock=200us, Fin=4MHz) = 800
str r1,[r0]
[ PLLONSTART
ldr r0,=PLLCON ;temporary setting of PLL
ldr r1,=((0xe8<<12)+(0x4<<4)+0x2) ;Fin=4MHz,Fvco=160Mhz,Fout=40MHz,m/p/s=0x48/0/0x2
str r1,[r0]
]
ldr r0,=CLKCON
ldr r1,=0x7ff8 ;All unit block CLK enable
str r1,[r0]
;****************************************************
;* Set memory control registers *
;****************************************************
ldr r0,=SMRDATA
ldmia r0,{r1-r13}
ldr r0,=0x01c80000 ;BWSCON Address
stmia r0,{r1-r13}
;****************************************************
;* Initialize stacks *
;****************************************************
ldr sp, =SVCStack ;Why?
bl InitStacks
;****************************************************
;* Setup IRQ handler *
;****************************************************
ldr r0,=HandleIRQ ;This routine is needed
ldr r1,=IRQ_Handler ;=IsrIRQ ;if there isn't 'subs pc,lr,#4' at 0x18, 0x1c
str r1,[r0]
IMPORT __main
[ :LNOT:THUMBCODE
BL __main ;Don't use main() because ......
B .
]
[ THUMBCODE ;for start-up code for Thumb mode
orr lr,pc,#1
bx lr
CODE16
bl Main ;Don't use main() because ......
b .
CODE32
]
;****************************************************
;* The function for initializing stack *
;****************************************************
IMPORT UserStack
IMPORT SVCStack
IMPORT UndefStack
IMPORT IRQStack
IMPORT AbortStack
IMPORT FIQStack
InitStacks
;Don't use DRAM,such as stmfd,ldmfd......
;SVCstack is initialized before
;Under toolkit ver 2.50, 'msr cpsr,r1' can be used instead of 'msr cpsr_cxsf,r1'
mrs r0,cpsr
bic r0,r0,#MODEMASK
orr r1,r0,#UNDEFMODE|NOINT
msr cpsr_cxsf,r1 ;UndefMode
ldr sp,=UndefStack
orr r1,r0,#ABORTMODE|NOINT
msr cpsr_cxsf,r1 ;AbortMode
ldr sp,=AbortStack
orr r1,r0,#IRQMODE|NOINT
msr cpsr_cxsf,r1 ;IRQMode
ldr sp,=IRQStack
orr r1,r0,#FIQMODE|NOINT
msr cpsr_cxsf,r1 ;FIQMode
ldr sp,=FIQStack
;bic r0,r0,#MODEMASK|NOINT
orr r1,r0,#SVCMODE|NOINT
msr cpsr_cxsf,r1 ;SVCMode
ldr sp,=SVCStack
;USER mode is not initialized.
mov pc,lr ;The LR register may be not valid for the mode changes.
;****************************************************
;* The function for entering power down mode *
;****************************************************
;void EnterPWDN(int CLKCON);
EnterPWDN
mov r2,r0 ;r0=CLKCON
ldr r0,=REFRESH
ldr r3,[r0]
mov r1, r3
orr r1, r1, #0x400000 ;self-refresh enable
str r1, [r0]
nop ;Wait until self-refresh is issued. May not be needed.
nop ;If the other bus master holds the bus, ...
nop ; mov r0, r0
nop
nop
nop
nop
;enter POWERDN mode
ldr r0,=CLKCON
str r2,[r0]
;wait until enter SL_IDLE,STOP mode and until wake-up
mov r0,#0xff
0 subs r0,r0,#1
bne %B0
;exit from DRAM/SDRAM self refresh mode.
ldr r0,=REFRESH
str r3,[r0]
mov pc,lr
LTORG
SMRDATA DATA
DCD BWSCON_cfg
DCD ((B0_Tacs<<13)+(B0_Tcos<<11)+(B0_Tacc<<8)+(B0_Tcoh<<6)+(B0_Tah<<4)+(B0_Tacp<<2)+(B0_PMC)) ;GCS0
DCD ((B1_Tacs<<13)+(B1_Tcos<<11)+(B1_Tacc<<8)+(B1_Tcoh<<6)+(B1_Tah<<4)+(B1_Tacp<<2)+(B1_PMC)) ;GCS1
DCD ((B2_Tacs<<13)+(B2_Tcos<<11)+(B2_Tacc<<8)+(B2_Tcoh<<6)+(B2_Tah<<4)+(B2_Tacp<<2)+(B2_PMC)) ;GCS2
DCD ((B3_Tacs<<13)+(B3_Tcos<<11)+(B3_Tacc<<8)+(B3_Tcoh<<6)+(B3_Tah<<4)+(B3_Tacp<<2)+(B3_PMC)) ;GCS3
DCD ((B4_Tacs<<13)+(B4_Tcos<<11)+(B4_Tacc<<8)+(B4_Tcoh<<6)+(B4_Tah<<4)+(B4_Tacp<<2)+(B4_PMC)) ;GCS4
DCD ((B5_Tacs<<13)+(B5_Tcos<<11)+(B5_Tacc<<8)+(B5_Tcoh<<6)+(B5_Tah<<4)+(B5_Tacp<<2)+(B5_PMC)) ;GCS5
[ BDRAMTYPE="DRAM"
DCD ((B6_MT<<15)+(B6_Trcd<<4)+(B6_Tcas<<3)+(B6_Tcp<<2)+(B6_CAN)) ;GCS6 check the MT value in parameter.a
DCD ((B7_MT<<15)+(B7_Trcd<<4)+(B7_Tcas<<3)+(B7_Tcp<<2)+(B7_CAN)) ;GCS7
| ;"SDRAM"
DCD ((B6_MT<<15)+(B6_Trcd<<2)+(B6_SCAN)) ;GCS6
DCD ((B7_MT<<15)+(B7_Trcd<<2)+(B7_SCAN)) ;GCS7
]
DCD ((REFEN<<23)+(TREFMD<<22)+(Trp<<20)+(Trc<<18)+(Tchr<<16)+REFCNT) ;REFRESH RFEN=1, TREFMD=0, trp=3clk, trc=5clk, tchr=3clk,count=1019
DCD 0x10 ;SCLK power down mode, BANKSIZE 32M/32M
DCD 0x20 ;MRSR6 CL=2clk
DCD 0x20 ;MRSR7
ALIGN
IMPORT HandleReset
IMPORT HandleUndef
IMPORT HandleSWI
IMPORT HandlePabort
IMPORT HandleDabort
IMPORT HandleReserved
IMPORT HandleIRQ
IMPORT HandleFIQ
IMPORT HandleADC
IMPORT HandleRTC
IMPORT HandleUTXD1
IMPORT HandleUTXD0
IMPORT HandleSIO
IMPORT HandleIIC
IMPORT HandleURXD1
IMPORT HandleURXD0
IMPORT HandleTIMER5
IMPORT HandleTIMER4
IMPORT HandleTIMER3
IMPORT HandleTIMER2
IMPORT HandleTIMER1
IMPORT HandleTIMER0
IMPORT HandleUERR01
IMPORT HandleWDT
IMPORT HandleBDMA1
IMPORT HandleBDMA0
IMPORT HandleZDMA1
IMPORT HandleZDMA0
IMPORT HandleTICK
IMPORT HandleEINT4567
IMPORT HandleEINT3
IMPORT HandleEINT2
IMPORT HandleEINT1
IMPORT HandleEINT0
END
?? 快捷鍵說明
復制代碼
Ctrl + C
搜索代碼
Ctrl + F
全屏模式
F11
切換主題
Ctrl + Shift + D
顯示快捷鍵
?
增大字號
Ctrl + =
減小字號
Ctrl + -