?? changelog
字號:
ChangeLog04.09.01(v5.36-9)===========================1. I2C 烹腳苞 包訪竅咯 角菩矯 3鍋 retry竅霸 薦鏈 (<-- linux device driver客 悼老)04.08.06(v5.36-8)===========================1. ADC ready interrupt mask...2. IOREGC 3.3V setting.(USB HOST包訪 冠苞厘 夸沒葷親)04.08.02(v5.36-7)===========================1. pmu all register setting(RTC,ADC block 力寇).04.07.31(v5.36-6)============================1.1.8V 傈盔傍鞭 救瀝拳, DCUDC2 <==0x00.04.07.26(v5.36-5)=============================1. pmu initialize routine core棺 PLD率 傈盔 犬牢竅咯 肋給等 單撈磐啊樂欄擱 礙力肺 促矯 write.04.07.22(v5.36-4)=============================1. pmu boot initialize何盒 付瘤阜 3 register setting 昏力.<-- 冠苞厘 累訣葷親.04.07.09(v5.36-3)=============================1. booting矯 main/remocon key check 竅擱輯 救喘礬臉闌錠檔 '0' 闌 EEPROM俊 write.04.07.07(v.5.36-2)=============================1.usb power ok包訪 control 眠啊. 0x19 <== 0xFE04.07.05(v.5.36-1)=============================1.power off 矯 sequence薦瀝.04.07.03(v.5.36-0)============================1. boot sequence 薦瀝. LPP饒 boot力措肺 救登綽 bug 薦瀝.04.06.29(v5.35-6)=============================1. booting矯 pmu control sequence 薦瀝. 1) pmu register initialize甫 sdram copy 撈傈欄肺 顆辮. 2) SDRAM bypass饒 pmu ldo init饒 108MHz肺 setting.04.06.23(v5.35-5)============================1. Booting矯 key(main power, remocon power)check 竅咯 eeprom俊 歷厘.04.06.17(v5.35-4)============================1. 規傈雀肺 眠啊 (GPO3 --> 'L') 04.05.21(v5.35-3)============================1. ES3 儈 --> CPU俊輯 keepact腳齲 'H' (GIO13) : hwinit_dm270.S04.05.13(ver5.35-2)===========================1. GPO0 : 'H' in Active, GPO1 : 'H' in Active.04.05.13(ver5.35-1)===========================1. GPOOD0 : 'L' in Active 'Hi-Z' in standby.04.05.12(ver5.35-0)===========================* ES2儈 利儈 1. accessary 俊 狼茄 interrupt enable.2. backup battery charging enable(standby/active), 400uA,3.0V3. MBCC main Battery charging disable(set to Idle mode)4. LPREGC1 regsiter output Off.5. OOCC1 : clk 32ON off, wake up by EXTON off.6. BVMC : Not fixed.7. LED control off.8. source俊輯 ethernet俊 包拌等 source(CS8900) compile俊輯 力寇.04.04.30(ver5.34-3.0)============================1. ES2儈 GPO2 LED1 output --> Hi-Z2. system clock setting. SDRAM,DSP : 108MHz ARM : 94.5MHz ACL : 189MHz04.04.24(ver5.34-2.7-test)============================1. test儈. system clock setting. ARM,SDRAM,DSP : 108MHz ACL : 189MHz04.04.23(ver5.34-2.7)=======================1. pmp device狼 reset button闌 喘范闌 錠 pmu俊輯 拌加 措扁竅綽 bug fix.04.04.14(ver5.34-2.6)======================1. Battery啊 low threashold voltage撈竅肺 凍絹瘤擱 stand by mode肺 皚.04.04.14(ver5.34-2.6)======================1. rrload俊輯 main battery check routine 火澇. main battery啊 3.6V焊促 累欄擱 stand by mode肺 皚.2. ADC module coding.04.04.02(ver5.34-2.5)======================1. debug message 薦瀝 2. 彌檬 charger俊 狼秦輯 enable 登菌闌 版快 促矯 stand by肺 傈券. --> charger俊 狼秦 pmu綽 enable登瘤 臼瀾.04.03.30(ver5.23-2.4)======================1.chager俊 包茄 葛電 interrupt mask. 1) INT2M <==0xff04.03.26======================1. power control for USB device power 1) 0x25 <== 0xf8 2) 0x26 <== 0xf004.03.23======================1. power on control 梅啊. 1) D1REGC1闌 power off 0x24 <== 0x06 1) DCUDDC1俊 1.8V set 0x21 <== 0xe3 04.03.22======================1. pmu 累訣 矯累.2. i2c module 火澇.3. pmu甫 烹茄 檬扁 power test.. 1) DCDC1 1.5V set 0x1b <== 0xf8 2) GPOC3闌 low active --> FFT open 0x3a <== 0x07 3) GPOC4甫 low active --> FFT open 0x3b <== 0xe3 4) LED1 pattern setting 0x36 <== 0x08 5) GPOC2俊 LED1 ouput enable 0x39 <== 0x01
?? 快捷鍵說明
復制代碼
Ctrl + C
搜索代碼
Ctrl + F
全屏模式
F11
切換主題
Ctrl + Shift + D
顯示快捷鍵
?
增大字號
Ctrl + =
減小字號
Ctrl + -