<Linux Base Driver for DM9013 adapter>DAVICOM Semiconductor Inc.				08/16/2006        A Davicom DM9013 Ethernet switch driver for Linux.         Copyright (C) 1997 2006  Sten Wang ,Jackal Huang        This program is free software; you can redistribute it and/or        modify it under the terms of the GNU General Public License        as published by the Free Software Foundation; either version 2        of the License, or (at your option) any later version.        This program is distributed in the hope that it will be useful,        but WITHOUT ANY WARRANTY; without even the implied warranty of        MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the        GNU General Public License for more details.        <A. Requirements>  kernel source tree (supported versions 2.4.x or 2.6.x)  compiler/binutils for kernel compilation  <B. Building and Installation>    B-1: Login as root.    B-2: Untar/unzip archive:  	tar -zxvf dm9sw_x.x.tar.gz  	  B-3: Change to the directory  	cd dm9sw_x.x  	  B-4: Compile the driver module  	-Kernel 2.4  	  Please according to your system to pick one.     	    make     	;;Without SMP support      	    make mod	;;Set version info on all module symbol     	    make smp	;;symmetric multi-processing(SMP) support     	    make smp_mod	;;SMP & Set version info on module	    		make checksum	;;Set TX/RX Checksum offload 	-Kernel 2.6	    make  B-5: Install the module:       -Kernel 2.4       insmod dm9sw.o <parameter>=<value>       -Kernel 2.6       insmod dm9sw.ko <parameter>=<value>  B-6: Assign an IP address to the interface by entering the following,        where x is the interface number:     	 ifconfig ethx <IP_address>  B-7: Verify that the interface works. Enter the following, where        <IP_address> is the IP address for another machine on the        same subnet as the interface that is being tested:            ping  <IP_address>            	  <C. The parameters of installing module>  If the driver is built as a module, the following optional parameters are   used by entering them on the command line with the modprobe or insmod command  using this syntax:     insmod dm9sw.[k]o [<parameter>=<VAL1>,<VAL2>,...]   The default value for each parameter is generally the recommended setting,  unless otherwise noted.    C-1: Intro parameters     - irq (IRQ number)    default value :3    ex.    	insmod irq=5 	;;inster module with irq number=5      - iobase (I/O base adddress)    default value: the program will reach from 0x300 to 0x370 automatically.    ex.    	insmod iobase=0x310 ;;inster module with I/O base address=0x310    	  - mode (Media Speed)    default value: Auto Detection    ex.    	insmod dm9sw.o           ;;Auto Detection Mode        insmod dm9sw.o mode=0    ;;Force 10M Half Duplex        insmod dm9sw.o mode=1    ;;Force 100M Half Duplex        insmod dm9sw.o mode=4    ;;Force 10M Full Duplex        insmod dm9sw.o mode=5    ;;Force 100M Full Duplex           C-2: For Redhat, You can use the following to Activate NIC		1.  login as root.	2.  copy dm9sw.[k]o into /lib/modules/2.4.x[2.6.x]/kernel/drivers/net/	3.  add the new line with "alias ethx dm9sw" in "/etc/module.conf". 	4.  execute "netconfig -d ethx".	5.  Fill your IP address, netmask and gateway	6.  press <ok> to confirm and exit this setting	7   reboot	DAVICOM Web-Site: www.davicom.com.tw