?? 復件 new.c
字號:
/******************************************************************************/
/* Name: LCD12864+DS1302+DS18B20+S52 */
/* */
/* Designed by :whoami Date:2005/11/13 */
/* */
/* http://www.mculover.net */
/******************************************************************************/
#include <reg51.h>
sbit Bell_Out = P1 ^ 7;//鬧鐘管腳輸出
sbit DQ = P2 ^ 1;//ds1820data
sbit clock_clk = P2 ^ 2;//ds1302_clk
sbit clock_dat = P2 ^ 3;//ds1302_dat
sbit clock_Rst = P2 ^ 4;//ds1302_Rst
#define Disp_On 0x3f //定義管腳的指令值
#define Disp_Off 0x3e
#define Col_Add 0x40
#define Page_Add 0xb8
#define Start_Line 0xc0
#define Lcd_Bus P0 //定義數據口
sbit Mcs = P3 ^ 5; //
sbit Scs = P3 ^ 6; //
sbit Enable = P1 ^ 5; //
sbit Di = P1 ^ 4; //
sbit RW = P1 ^ 3; //
sbit Lcd_Rst= P3 ^ 7; //
//鍵盤掃描
sbit Add_Key = P1 ^ 0;//加1鍵
sbit Dec_Key = P1 ^ 1;//減1鍵
sbit OK_Key = P1 ^ 2;//確定鍵
//24存儲器
sbit SCL = P3 ^ 3;
sbit SDA = P3 ^ 4;
sbit WP = P3 ^ 2;
#define TRUE 1
#define FALSE 0
#define Delay2408_TIME 60 //經實驗，不要小于50！否則可能造成時序混亂
//為了編程方便定義的位變量
sbit a0 = ACC ^ 0;
sbit a1 = ACC ^ 1;
sbit a2 = ACC ^ 2;
sbit a3 = ACC ^ 3;
sbit a4 = ACC ^ 4;
sbit a5 = ACC ^ 5;
sbit a6 = ACC ^ 6;
sbit a7 = ACC ^ 7;
bit flag, Bell_Swh,Hourb,Minb,Secb,Kgb;//閃爍標志位
bit sec=0,min=0,hour=0,year=0,mon=0,day=0,weekk=0; //閃爍標志位
unsigned char id,id2,d,e,S_1302,H_1302,H_2402,S_2402; //
//Function Definition 函數聲明
void Delay(int num);
void Init_DS18B20(void);
unsigned char ReadOneChar(void);
void WriteOneChar(unsigned char dat);
unsigned int ReadTemperature(void);
void clock_out(unsigned char dd);
unsigned char clock_in(void);
unsigned char read_clock(unsigned char ord);
void write_clock(unsigned char ord, unsigned char dd);
void Disp(void);
void id_case1_key(void);
void id_case2_key(void);
void Set_time(unsigned char sel,bit sel_1);
void Timer0_Init(void);
void Init_1302(void);
void Set_Bell(unsigned char sel, bit sel_1);
//24系列
void Delay2408(unsigned int t);
void I2C_Start(void);
void I2C_Stop(void);
void SEND_0(void);
void SEND_1(void);
bit Check_Acknowledge(void);
void WriteI2CByte(unsigned char b)reentrant;
unsigned char ReadI2CByte(void)reentrant;
void Write_One_Byte(unsigned char addr,unsigned char thedata);
char Read_One_Byte(unsigned char addr);
//12864
void Delay12864(unsigned int t);
void write_com(unsigned char cmdcode);
void write_data(unsigned char Dispdata);
void frame(void);
void Clr_Scr(void);
void Disp_Img(unsigned char code *img);
void Disp_Digit(unsigned char pag,unsigned char col, unsigned char code *hzk);
void Disp_Chinese(unsigned char pag,unsigned char col, unsigned char code *hzk);
void Init_lcd(void);
//漢字庫及數字符號庫
unsigned char code nao[32]={0x00,0x00,0xF9,0x12,0x90,0x92,0x96,0xFA,0x92,0x92,0x92,0x12,0x02,0xFE,0x00,0x00,
0x00,0x00,0xFF,0x00,0x1F,0x00,0x00,0x7F,0x00,0x08,0x1F,0x40,0x80,0x7F,0x00,0x00};/*-- 文字: 鬧 --*/
unsigned char code zhong[32]={0x40,0x30,0x2C,0xEB,0x28,0x28,0x00,0xF8,0x08,0x08,0xFF,0x08,0x08,0xF8,0x00,0x00,
0x01,0x01,0x01,0xFF,0x41,0x21,0x00,0x01,0x01,0x01,0xFF,0x01,0x01,0x01,0x00,0x00};/*-- 文字: 鐘 --*/
unsigned char code she[32]={0x40,0x41,0xCE,0x04,0x00,0x80,0x40,0xBE,0x82,0x82,0x82,0xBE,0xC0,0x40,0x40,0x00,
0x00,0x00,0x7F,0x20,0x90,0x80,0x40,0x43,0x2C,0x10,0x10,0x2C,0x43,0xC0,0x40,0x00};/*-- 文字: 設 --*/
unsigned char code ding[32]={0x00,0x10,0x0C,0xA4,0x24,0x24,0x25,0xE6,0x24,0x24,0x24,0x24,0x14,0x0C,0x04,0x00,
0x40,0x20,0x18,0x07,0x08,0x10,0x20,0x7F,0x42,0x42,0x42,0x42,0x40,0x40,0x00,0x00};/*-- 文字: 定 --*/
unsigned char code kai[32]={0x40,0x42,0x42,0x42,0x42,0xFE,0x42,0x42,0x42,0x42,0xFE,0x42,0x42,0x42,0x42,0x00,
0x00,0x40,0x20,0x10,0x0C,0x03,0x00,0x00,0x00,0x00,0x7F,0x00,0x00,0x00,0x00,0x00};/*-- 文字: 開 --*/
unsigned char code guan[32]={0x00,0x10,0x10,0x10,0x11,0x1E,0x14,0xF0,0x10,0x18,0x17,0x12,0x18,0x10,0x00,0x00,
0x01,0x81,0x41,0x21,0x11,0x09,0x05,0x03,0x05,0x09,0x31,0x61,0xC1,0x41,0x01,0x00};/*-- 文字: 關 --*/
unsigned char code shit[32]={0x00,0xFC,0x44,0x44,0x44,0xFC,0x10,0x90,0x10,0x10,0x10,0xFF,0x10,0x10,0x10,0x00,
0x00,0x07,0x04,0x04,0x04,0x07,0x00,0x00,0x03,0x40,0x80,0x7F,0x00,0x00,0x00,0x00};/*-- 文字: 時 --*/
unsigned char code jian[32]={0x00,0xF8,0x01,0x06,0x00,0xF0,0x92,0x92,0x92,0x92,0xF2,0x02,0x02,0xFE,0x00,0x00,
0x00,0xFF,0x00,0x00,0x00,0x07,0x04,0x04,0x04,0x04,0x07,0x40,0x80,0x7F,0x00,0x00};/*-- 文字: 間 --*/
unsigned char code dao[32]={0x00,0x22,0x72,0x2A,0x26,0xE2,0x2A,0x72,0x22,0x00,0xF8,0x00,0x00,0xFF,0x00,0x00,
0x00,0x42,0xC2,0x42,0x22,0x3F,0x22,0x12,0x12,0x00,0x0F,0x40,0x80,0x7F,0x00,0x00};/*-- 文字: 到 --*/
unsigned char code shi[32]={0x00,0x10,0x2C,0x24,0xA4,0x64,0x25,0x26,0x24,0x24,0xA4,0x24,0x34,0x2C,0x04,0x00,
0x40,0x40,0x48,0x49,0x49,0x49,0x49,0x7F,0x49,0x49,0x49,0x4B,0x48,0x40,0x40,0x00};//室
unsigned char code wen[32]={0x10,0x21,0x86,0x70,0x00,0x7E,0x4A,0x4A,0x4A,0x4A,0x4A,0x7E,0x00,0x00,0x00,0x00,
0x02,0xFE,0x01,0x40,0x7F,0x41,0x41,0x7F,0x41,0x41,0x7F,0x41,0x41,0x7F,0x40,0x00};//溫
unsigned char code zero[16]={0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x0F,0x10,0x20,0x20,0x10,0x0F,0x00};//0
unsigned char code one[16]={0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00};//1
unsigned char code two[16]={0x00,0x70,0x08,0x08,0x08,0x88,0x70,0x00,0x00,0x30,0x28,0x24,0x22,0x21,0x30,0x00};//2
unsigned char code three[16]={0x00,0x30,0x08,0x88,0x88,0x48,0x30,0x00,0x00,0x18,0x20,0x20,0x20,0x11,0x0E,0x00};//3
unsigned char code four[16]={0x00,0x00,0xC0,0x20,0x10,0xF8,0x00,0x00,0x00,0x07,0x04,0x24,0x24,0x3F,0x24,0x00};//4
unsigned char code five[16]={0x00,0xF8,0x08,0x88,0x88,0x08,0x08,0x00,0x00,0x19,0x21,0x20,0x20,0x11,0x0E,0x00};//5
unsigned char code six[16]={0x00,0xE0,0x10,0x88,0x88,0x18,0x00,0x00,0x00,0x0F,0x11,0x20,0x20,0x11,0x0E,0x00};//6
unsigned char code seven[16]={0x00,0x38,0x08,0x08,0xC8,0x38,0x08,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,0x00};//7
unsigned char code eight[16]={0x00,0x70,0x88,0x08,0x08,0x88,0x70,0x00,0x00,0x1C,0x22,0x21,0x21,0x22,0x1C,0x00};//8
unsigned char code nine[16]={0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x00,0x31,0x22,0x22,0x11,0x0F,0x00};//9
unsigned char code point[16]={0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,0x00,0x00};//小數點
unsigned char code maohao[16]={0x00,0x00,0x00,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00};//冒號
unsigned char code space[16]={0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00};//空白
unsigned char code fh[16]={0x00,0x00,0x00,0xFC,0xFC,0x00,0x00,0x00,0x00,0x00,0x00,0x6F,0x6F,0x00,0x00,0x00};//!感嘆號
unsigned char code nian[32]={0x40,0x20,0x10,0x0C,0xE3,0x22,0x22,0x22,0xFE,0x22,0x22,0x22,0x22,0x02,0x00,0x00,
0x04,0x04,0x04,0x04,0x07,0x04,0x04,0x04,0xFF,0x04,0x04,0x04,0x04,0x04,0x04,0x00};//年
unsigned char code yue[32]={0x00,0x00,0x00,0x00,0x00,0xFF,0x11,0x11,0x11,0x11,0x11,0xFF,0x00,0x00,0x00,0x00,
0x00,0x40,0x20,0x10,0x0C,0x03,0x01,0x01,0x01,0x21,0x41,0x3F,0x00,0x00,0x00,0x00};//月
unsigned char code xing[32]={0x00,0x00,0x00,0xBE,0x2A,0x2A,0x2A,0xEA,0x2A,0x2A,0x2A,0x2A,0x3E,0x00,0x00,0x00,
0x00,0x48,0x46,0x41,0x49,0x49,0x49,0x7F,0x49,0x49,0x49,0x49,0x49,0x41,0x40,0x00};//星
unsigned char code qi[32]={0x00,0x04,0xFF,0x54,0x54,0x54,0xFF,0x04,0x00,0xFE,0x22,0x22,0x22,0xFE,0x00,0x00,
0x42,0x22,0x1B,0x02,0x02,0x0A,0x33,0x62,0x18,0x07,0x02,0x22,0x42,0x3F,0x00,0x00};//期
unsigned char code cone[32]={0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0xC0,0x80,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00};//一
unsigned char code ctwo[32]={0x00,0x00,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x06,0x04,0x00,0x00,0x00,
0x00,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x18,0x10,0x00};//二
unsigned char code cthree[32]={0x00,0x04,0x84,0x84,0x84,0x84,0x84,0x84,0x84,0x84,0x84,0x84,0x84,0x04,0x00,0x00,
0x00,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x00};//三
unsigned char code cfour[32]={0x00,0xFE,0x02,0x02,0x02,0xFE,0x02,0x02,0xFE,0x02,0x02,0x02,0x02,0xFE,0x00,0x00,
0x00,0x7F,0x28,0x24,0x23,0x20,0x20,0x20,0x21,0x22,0x22,0x22,0x22,0x7F,0x00,0x00};//四
unsigned char code cfive[32]={0x00,0x02,0x82,0x82,0x82,0x82,0xFE,0x82,0x82,0x82,0xC2,0x82,0x02,0x00,0x00,0x00,
0x20,0x20,0x20,0x20,0x20,0x3F,0x20,0x20,0x20,0x20,0x3F,0x20,0x20,0x30,0x20,0x00};//五
unsigned char code csix[32]={0x10,0x10,0x10,0x10,0x10,0x91,0x12,0x1E,0x94,0x10,0x10,0x10,0x10,0x10,0x10,0x00,
0x00,0x40,0x20,0x10,0x0C,0x03,0x01,0x00,0x00,0x01,0x02,0x0C,0x78,0x30,0x00,0x00};//六
unsigned char code ri[32]={0x00,0x00,0x00,0xFE,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0xFE,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x3F,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x3F,0x00,0x00,0x00,0x00};//日
unsigned char code sheshidu[32]={0x00,0x02,0x05,0xE2,0x18,0x04,0x02,0x02,0x02,0x02,0x02,0x02,0x04,0x1E,0x00,0x00,
0x00,0x00,0x00,0x07,0x18,0x20,0x40,0x40,0x40,0x40,0x40,0x40,0x20,0x18,0x00,0x00};//攝氏度的符號
unsigned char code spaces[32]={0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00};//漢字空格
unsigned char code biaozhi[32]={0x00,0x00,0x00,0x00,0xE0,0xF8,0xFC,0xFC,0xFC,0xFC,0xF8,0xE0,0x00,0x00,0x00,0x00,
0x00,0x10,0x18,0x3E,0x3F,0x7F,0x5F,0x9F,0x9F,0x5F,0x7F,0x3F,0x3E,0x18,0x10,0x00};//鬧鐘的圖標
/******************************************************************************/
/* 24C08.c*/
//調用方式如下：
//Write_One_Byte(0x10,0x04);
//k=Read_One_Byte(0x10);
/********** 函數定義 ************/
void Delay2408(unsigned int t) /*延時函數*/
{
while(t!=0)
t--;
}
void I2C_Start(void)
{
/*啟動I2C總線的函數，當SCL為高電平時使SDA產生一個負跳變*/
SDA=1;
SCL=1;
Delay2408(Delay2408_TIME);
SDA=0;
Delay2408(Delay2408_TIME);
SCL=0;
Delay2408(Delay2408_TIME);
}
void I2C_Stop(void)
{
/*終止I2C總線，當SCL為高電平時使SDA產生一個正跳變*/
SDA=0;
SCL=1;
Delay2408(Delay2408_TIME);
SDA=1;
Delay2408(Delay2408_TIME);
SCL=0;
Delay2408(Delay2408_TIME);
}
void SEND_0(void) /* SEND ACK */
{
/*發送0，在SCL為高電平時使SDA信號為低*/
SDA=0;
SCL=1;
Delay2408(Delay2408_TIME);
SCL=0;
Delay2408(Delay2408_TIME);
}
void SEND_1(void)
{
/*發送1，在SCL為高電平時使SDA信號為高*/
SDA=1;
SCL=1;
Delay2408(Delay2408_TIME);
SCL=0;
Delay2408(Delay2408_TIME);
}
bit Check_Acknowledge(void)
{
/*發送完一個字節后檢驗設備的應答信號*/
SDA=1;
SCL=1;
Delay2408(Delay2408_TIME/2);
F0=SDA;
Delay2408(Delay2408_TIME/2);
SCL=0;
Delay2408(Delay2408_TIME);
if(F0==1)
return FALSE;
return TRUE;
}
void WriteI2CByte(unsigned char b)reentrant
{
/*向I2C總線寫一個字節*/
unsigned char i;
for(i=0;i<8;i++)
if((b<<i)&0x80)
SEND_1();
else
SEND_0();
}
unsigned char ReadI2CByte(void)reentrant
{
/*從I2C總線讀一個字節*/
unsigned char b=0,i;
for(i=0;i<8;i++)
{
SDA=1; /*釋放總線*/
SCL=1; /*接受數據*/
Delay2408(10);
F0=SDA;
Delay2408(10);
SCL=0;
if(F0==1)
{
b=b<<1;
b=b|0x01;
}
else
b=b<<1;
}
return b;
}
/**********以下為讀寫24c02的函數***********************************************/
void Write_One_Byte(unsigned char addr,unsigned char thedata)
{
bit acktemp=1;
/*write a byte to mem*/
I2C_Start();
WriteI2CByte(0xa0);
acktemp=Check_Acknowledge();
WriteI2CByte(addr); /*address*/
acktemp=Check_Acknowledge();
WriteI2CByte(thedata); /*thedata*/
acktemp=Check_Acknowledge();
I2C_Stop();
}
/******************************************************************************/
char Read_One_Byte(unsigned char addr)
{
bit acktemp=1;
unsigned char mydata;
/*read a byte from mem*/
I2C_Start();
WriteI2CByte(0xa0);
acktemp=Check_Acknowledge();
WriteI2CByte(addr);/*address*/
acktemp=Check_Acknowledge();
I2C_Start();
WriteI2CByte(0xa1);
acktemp=Check_Acknowledge();
mydata=ReadI2CByte();
acktemp=Check_Acknowledge();
return mydata;
I2C_Stop();
}
/******************************************************************************/
void Delay(int num)//延時函數
{
while(num--) ;
}
/*12864driver.c*/
/******************************************************************************/
void Delay12864(unsigned int t)//
{
unsigned int i,j;
for(i=0;i<t;i++)
{
for(j=0;j<10;j++);
}
}
/******************************************************************************/
void write_com(unsigned char cmdcode)//寫命令到LCD
{
Di = 0;
RW = 0;
Lcd_Bus = cmdcode;
Delay12864(0);
Enable = 1;
Delay12864(0);
Enable = 0;
}
/******************************************************************************/
void write_data(unsigned char Dispdata)//寫數據到LCD
{
Di = 1;
RW = 0;
Lcd_Bus = Dispdata;
Delay12864(0);
Enable = 1;
Delay12864(0);
Enable = 0;
}
/*******************************************************************************/
void frame(void)//顯示邊框
{
unsigned char i;
Mcs = 1;
Scs = 1;
write_com(Page_Add+0);
write_com(Col_Add+0);
for(i=0;i<64;i++)
{
write_data(0x01);
}
write_com(Page_Add+7);
write_com(Col_Add+0);
for(i=0;i<64;i++)
{
write_data(0x80);
}
for(i=0;i<8;i++)
{
Mcs=0;
Scs=1;
write_com(Page_Add+i);
write_com(Col_Add+63);
write_data(0xff);
Mcs=1;
Scs=0;
write_com(Page_Add+i);
write_com(Col_Add+0);
write_data(0xff);
}
}
/******************************************************************************/
void Clr_Scr(void)//清除內存
{
unsigned char j,k;
Mcs=1;Scs=1;
write_com(Page_Add+0);
write_com(Col_Add+0);
for(k=0;k<8;k++)
{
write_com(Page_Add+k);
write_com(Col_Add+0);
for(j=0;j<64;j++)
{
write_data(0x00);
}
}
}
/*******************************************************************************/
void Disp_Img(unsigned char code *img)//顯示12864圖片
{
unsigned char j,k;
for(k=0;k<8;k++)
{
Mcs=1;
Scs=0;
Delay(10);
write_com(Page_Add+k);
write_com(Col_Add+0);
for(j=0;j<64;j++)
{
write_data(img[k*128+j]);
}
Mcs=0;
Scs=1;
Delay(10);
write_com(Page_Add+k);
?? 快捷鍵說明
復制代碼
Ctrl + C
搜索代碼
Ctrl + F
全屏模式
F11
切換主題
Ctrl + Shift + D
顯示快捷鍵
?
增大字號
Ctrl + =
減小字號
Ctrl + -