#include "c:\keil\c51\inc\atmel\at89x52.h"
#include "intrins.h"
typedef unsigned char UINT8;
typedef unsigned int UINT16;
#define sclk P3_0
#define dat P3_1


void delay_100us()
{
        UINT8 i = 50;
        while (i--);
}
UINT8 CheckSum(UINT8 dat)
{
	UINT8 temp,i;

	for ( temp = 0,i= 0; i< 8;i++)
	{
	    temp += (dat & 0x01);
		dat >>= 1;
	}
	temp += 1;
	temp &= 0x01;     //求奇偶校驗和，偶數個1為1
	return temp;
}

UINT8 PCSendComm(UINT8 comm)
{
	UINT8 i;
	UINT8 checksum;
	sclk = 0;  			//拉低時鐘線
    //delay_100us();
	checksum = CheckSum(comm);  		//求檢驗和

	dat = 0;						//發送起始低電平
	sclk = 1;
	while (sclk);                 	//等待出現下降沿
	while (!sclk);              	//等待下個時鐘上升沿

	dat = comm & 0x01; 				//發送DATA0
	comm >>= 1;						//在時鐘上升沿轉換數據
	while (sclk);                 	//等待出現下降沿
	while (!sclk);              	//等待下個時鐘上升沿

	dat = comm & 0x01; 				//發送DATA1
	comm >>= 1;						//在時鐘上升沿轉換數據
	while (sclk);                 	//等待出現下降沿
	while (!sclk);              	//等待下個時鐘上升沿

	dat = comm & 0x01; 				//發送DATA2
	comm >>= 1;						//在時鐘上升沿轉換數據
	while (sclk);                 	//等待出現下降沿
	while (!sclk);              	//等待下個時鐘上升沿

	dat = comm & 0x01; 				//發送DATA3
	comm >>= 1;						//在時鐘上升沿轉換數據
	while (sclk);                 	//等待出現下降沿
	while (!sclk);              	//等待下個時鐘上升沿

	dat = comm & 0x01; 				//發送DATA4
	comm >>= 1;						//在時鐘上升沿轉換數據
	while (sclk);                 	//等待出現下降沿
	while (!sclk);              	//等待下個時鐘上升沿

	dat = comm & 0x01; 				//發送DATA5
	comm >>= 1;						//在時鐘上升沿轉換數據
	while (sclk);                 	//等待出現下降沿
	while (!sclk);              	//等待下個時鐘上升沿

	dat = comm & 0x01; 				//發送DATA6
	comm >>= 1;						//在時鐘上升沿轉換數據
	while (sclk);                 	//等待出現下降沿
	while (!sclk);              	//等待下個時鐘上升沿

	dat = comm & 0x01; 				//發送DATA7
	while (sclk);                 	//等待出現下降沿
	while (!sclk);              	//等待下個時鐘上升沿

	dat = checksum; 				//發送檢驗和
	while (sclk);                 	//等待出現下降沿
	while (!sclk);              	//等待下個時鐘上升沿

	dat = 1;						//發送停止位1
	while (sclk);                 	//等待出現下降沿
	while (!sclk);                  //等待高電平結束！！很重要，必須

    checksum = 0;
    checksum |= dat;                 //下降沿時讀取從機ACK

	return checksum;
}


UINT8 PCReceData()
{	UINT8 rece_data = 0;
	UINT8 checksum,temp;
	while (sclk); 					//等待從機應答的第一個時鐘下降沿出現
	if (!dat)						//檢查是否收到開始低電平，否則停止接收
	{
		while (!sclk);				//等待起始低電平結束

		while (sclk);				//等待時鐘下降沿，接收data0
		rece_data |= dat;  		//時鐘下降沿接收數據
		while (!sclk);              //等待時鐘低電平結束

		while (sclk);				//等待時鐘下降沿，接收data1
		temp  = dat;
        temp <<= 1;
		rece_data |= temp;  		//時鐘下降沿接收數據
		while (!sclk);              //等待時鐘低電平結束

		while (sclk);				//等待時鐘下降沿，接收data2
		temp  = dat;
        temp <<= 2;
		rece_data |= temp;  		//時鐘下降沿接收數據
		while (!sclk);              //等待時鐘低電平結束

		while (sclk);				//等待時鐘下降沿，接收data3
		temp  = dat;
        temp <<= 3;
		rece_data |= temp;  		//時鐘下降沿接收數據
		while (!sclk);              //等待時鐘低電平結束

		while (sclk);				//等待時鐘下降沿，接收data4
		temp  = dat;
        temp <<= 4;
		rece_data |= temp;  		//時鐘下降沿接收數據
		while (!sclk);              //等待時鐘低電平結束

		while (sclk);				//等待時鐘下降沿，接收data5
		temp  = dat;
        temp <<= 5;
		rece_data |= temp;  		//時鐘下降沿接收數據
		while (!sclk);              //等待時鐘低電平結束

		while (sclk);				//等待時鐘下降沿，接收data6
		temp  = dat;
        temp <<= 6;
		rece_data |= temp;  		//時鐘下降沿接收數據
		while (!sclk);              //等待時鐘低電平結束

		while (sclk);				//等待時鐘下降沿，接收data7
		temp  = dat;
        temp <<= 7;
		rece_data |= temp;  			//時鐘下降沿接收數據
		while (!sclk);              //等待時鐘低電平結束

		while (sclk);				//等待時鐘下降沿，接收data0
		checksum |= dat;  			//時鐘下降沿接收數據
		while (!sclk);              //等待時鐘低電平結束

        while (sclk);
        if (!dat) return 0;
        while (!sclk);
        temp = CheckSum(rece_data);
        if ( temp != checksum)  return 0;
        else return rece_data;
        }
}

#define COMM_CONFIG_LED 0xed
#define COMM_RESET     0xff
#define COMM_DISABLE_KEY 0xf5
#define COMM_ENABLE_KEY 0xf4
#define COMM_ACK     0xfa
#define COMM_RESEND  0xfe
#define COMM_CONFIG_RATE   0xf3

#define NUM_LED  0x02
#define CAPS_LED 0x04
#define SCROLL_LED 0x01
void config_led(UINT8 led)
{
	led &= 0x07;
        do
        {
	       while (PCSendComm(COMM_CONFIG_LED));
        }while (PCReceData() != COMM_ACK);
	while (PCSendComm(led));
}

//keyrate 
void config_keyrate(UINT8 keyrate)
{
        keyrate &= 0x7f;
        do
        {
	       while (PCSendComm(COMM_CONFIG_RATE));
        }while (PCReceData() != COMM_ACK);
	while (PCSendComm(keyrate));
}        






void main()
{       UINT8 temp;

 PCSendComm(COMM_RESET);
 PCSendComm(COMM_DISABLE_KEY );
 PCSendComm(COMM_ENABLE_KEY );
 
 config_keyrate(0x21);
  config_keyrate(0x28);
  
   config_keyrate(0x2f);
 
 config_led(NUM_LED);
 config_led(CAPS_LED);
 config_led(SCROLL_LED|CAPS_LED|NUM_LED);
 config_led(CAPS_LED);
}