////////////////////////////////////////////////////////////////////////////////
// Cypress Semiconductor - Customer Design Center 
////////////////////////////////////////////////////////////////////////////////
// File:		hub_811.c
// Purpose:	    8051 firmware to master SL811 downstream hub (CY7C651xx). 
//              Contains hub-related control firmware. 
//              Based on SL811HST code written by cxn.
// H/W Target:  SL811HST(Rev 1.5) + EZUSB DEV KIT
// IMPORTANT :  Turn ON SW4 of S6-DIP-SWITCH 
//              to enable upper 32K memory on EZUSB Dev Kit
//
// $Header: /USB/ez811/firmware/Emb_Host/hub_811.c 7     5/17/02 6:09p Tpm $
// Copyright (c) 2002 Cypress Semiconductor. May not be reproduced without permission.
// See the license agreement for more details.
////////////////////////////////////////////////////////////////////////////////

#include "host_811.h"

extern xdata BYTE 			STATUS[8];		// for status data buffer
extern xdata BYTE 			HubChange[1];	// Hub port endpoint 1 data status
extern xdata BYTE 			pNumPort;		// Number of downstream ports on hub
extern xdata pHUBDEV		uHub;			// Struct for downstream device on HUB
extern xdata pPortStatus	pStat;			// HID ports status

//*****************************************************************************************
// Hub's downstream ports enumeration routine
//*****************************************************************************************
int HubPortEnum(void)
{
	xdata BYTE 	DevAddr, PortNum=0, PortSel;
	xdata BYTE	j=0;
//	xdata BYTE	TempDevAddr;

	PortSel = 0x02;											// start with port 1 first
	while(j++ < pNumPort)									// loop for all 4 port, bit 1 to bit 4
	{
		if(!(HubChange[0]&PortSel))							// test if bit representing port is set
		{
			PortSel <<= 1;									// shift mask to test for next bit port
		}
		else
		{
			switch(HubChange[0]&PortSel)					// valid downstream port number #1..#4 only
			{
				case 0x02:	PortNum = 0x01;	break;			// Limit to onboard hub with 4 downstream ports
				case 0x04:	PortNum = 0x02; break;			//
				case 0x08:	PortNum = 0x03; break;			//
				case 0x10:	PortNum = 0x04; break;			//
				default:	PortNum = HubChange[0]; break;	// for debug purpose
			}
			break;											// found one port, exit while loop now
		}
	}

	// Always use USB address #1 for HUB communication
	pStat =(pPortStatus)STATUS;								// keep current wPortStatus & wPortChange
	if (!GetPortStatus(HUB_ADDR,PortNum,STATUS)) return 0;	// If the device is already attached to hub

	//------------------------------------------------------------------------------
	// Device is present on current downstream port
	//------------------------------------------------------------------------------
	if((pStat->wPortStatus_Lo)&0x01)						
	{	
		//------------------------------------------------
		// Search for unused USB address (#2..#5 valid)
		//------------------------------------------------
		for(DevAddr=HUB_ADDR + 1; DevAddr<MAX_DEV; DevAddr++)	
		{
			if(uHub.bPortPresent[DevAddr] == 0)
			  break;
		}
		if(DevAddr == MAX_DEV)
		{
          DevAddr = 0;                                  // open port not found (shouldn't happen)
		  return 0;
		}

		//------------------------------------------------
		// Reset current attached downstream port device
		//------------------------------------------------
		if (!PortFeature(HUB_ADDR,CLEAR_FEATURE,C_PORT_CONNECTION,PortNum)) return 0;
		do{ // Clear C_PORT_CONNECTION state
			if (!GetPortStatus(HUB_ADDR,PortNum,STATUS)) return 0;
        }
		while(((pStat->wPortChange_Lo)&USB_PORT_STAT_C_CONNECTION));

		
		if (!PortFeature(HUB_ADDR,SET_FEATURE,PORT_RESET,PortNum)) return 0;	// reset this port for at least 10ms
		EZUSB_Delay(10);
		do{ // Set PORT_RESET 
			if (!GetPortStatus(HUB_ADDR,PortNum,STATUS)) return 0;
        }
		while( !((pStat->wPortChange_Lo)&USB_PORT_STAT_C_RESET) );

				
		if (!PortFeature(HUB_ADDR,CLEAR_FEATURE,C_PORT_RESET,PortNum)) return 0;
		do{ // Clear C_PORT_RESET state
			if (!GetPortStatus(HUB_ADDR,PortNum,STATUS)) return 0;
        }
		while(((pStat->wPortChange_Lo)&USB_PORT_STAT_C_RESET));
	
		//------------------------------------------------
		// Determine attached downstream speed
		//------------------------------------------------
		if ((pStat->wPortStatus_Hi)&0x02)								// check bit 9 of wPortStatus for port speed
			uHub.bPortSpeed[0] = uHub.bPortSpeed[DevAddr] = 1;			// '1' - lowspeed, USB address 0 must also be set
		else								
			uHub.bPortSpeed[0] = uHub.bPortSpeed[DevAddr] = 0;			// '0' - fullspeed, USB address 0 must also be set
				
		//------------------------------------------------
		// Enumerate current attached device on hub
		//------------------------------------------------
		EZUSB_Delay(50);							// some device require a long delay before it can enumerate properly
		if (!EnumUsbDev(DevAddr))					// enumerate device attached to current hub downstream port
			return 0;

		uHub.bPortPresent[DevAddr] = 1;				// set USB device present on this address	
		uHub.bPortNumber[DevAddr] = PortNum;		// Save port number used in this address
		switch(PortNum)		     		            // Downstream port #
		{											//
		//	case 1:	OUTA &= ~PORT1_LED; break;		// Downstream Port #1
			case 1: LightLed(1,1);		break;
		//	case 2:	OUTA &= ~PORT2_LED; break;		// Downstream Port #2
			case 2: LightLed(2,1);		break;
		//	case 3:	OUTA &= ~PORT3_LED; break;		// Downstream Port #3
			case 3: LightLed(3,1);		break;
		//	case 4:	OUTA &= ~PORT4_LED; break;		// Downstream Port #4
			case 4: LightLed(4,1);		break;
			default: break;
		}				
	}

	//------------------------------------------------------------------------------
	// Device is not present on current downstream port
	//------------------------------------------------------------------------------
	else
	{
		do{	// Clear C_PORT_CONNECTION state
		    if (!PortFeature(HUB_ADDR,CLEAR_FEATURE,C_PORT_CONNECTION,PortNum)) return 0;
			if (!GetPortStatus(HUB_ADDR,PortNum,STATUS)) return 0;
        }						//
		while(((pStat->wPortChange_Lo)&USB_PORT_STAT_C_CONNECTION));

		do{	// Clear C_PORT_ENABLE state - PORT_ENABLE was set for some hub only
		    if (!PortFeature(HUB_ADDR,CLEAR_FEATURE,C_PORT_ENABLE,PortNum)) return 0;
			if (!GetPortStatus(HUB_ADDR,PortNum,STATUS)) return 0;
        }						//
		while(((pStat->wPortChange_Lo)&USB_PORT_STAT_C_ENABLE));

		//------------------------------------------------
		// Search Port Number that was detached
		//------------------------------------------------
		for(DevAddr=HUB_ADDR + 1; DevAddr<MAX_DEV; DevAddr++)	
		{                                               // find the device
			if(uHub.bPortNumber[DevAddr]==PortNum)
			  break;
		}
		if(DevAddr == MAX_DEV)
          DevAddr = 0;                                  // device not found
		if(DevAddr)
		{
		  uHub.bPortPresent[DevAddr] = 0;			    // clear USB device present on this address		
		  uHub.bPortNumber[DevAddr] = 0;			    // clear port number for this failed address
		  switch(uHub.bPortNumber[DevAddr])				// Downstream port #
		  {												//
		//	case 1:	OUTA |= PORT1_LED; break;			// Downstream Port #1
			case 1: LightLed(1,0);	   break;
		//	case 2:	OUTA |= PORT2_LED; break;			// Downstream Port #2
			case 2: LightLed(2,0);	   break;
		//	case 3:	OUTA |= PORT3_LED; break;			// Downstream Port #3
			case 3: LightLed(3,0);	   break;
		//	case 4:	OUTA |= PORT4_LED; break;			// Downstream Port #4
			case 4: LightLed(4,0);	   break;
			default: break;
		  }	
		}
	}
	return DevAddr;
}