2002-12-12  Brian S. Dean  <bsd@bsdhome.com>	* main.c: minor cleanup2002-12-07  Brian S. Dean  <bsd@bsdhome.com>	* avrdude.1, main.c:	If the stk500 is being used, default to using the first serial port.2002-12-03  Brian S. Dean  <bsd@bsdhome.com>	* avrdude.1: Mention STK500 support.2002-12-01  Brian S. Dean  <bsd@bsdhome.com>	* stk500.c: Remove unused code.	* CHANGELOG, stk500.c:	Document changes since the previous version in the CHANGELOG.	Cleanup stk500.c a bit.	* stk500.c: Fix cut and paste braino.	* avr.c, avrdude.conf.sample, main.c, pgm.h, stk500.c:	The STK500 can perform paged read/write operations even on standard	"non-paged" parts.  Take advantage of that and use the faster internal	routines of the STK500 for those parts as well.	* avr.c, avr.h, avrpart.h, main.c, pgm.c, pgm.h, stk500.c:	Optimize reading and writing for the STK500 programmer if the part	supports paged reads and writes.  This greatly decreases the	program/verify time from about 4.5 minutes down to about 10 seconds in	a 12K program size test case.	Print out the hardware and firmware version for the STK500 if verbose	is enabled.	* avrdude.conf.sample, avrpart.h, config_gram.y, lexer.l, pgm.h:	* ppi.c, ppi.h, stk500.c, stk500.h, stk500_private.h:	Add basic support for STK500.2002-11-30  Brian S. Dean  <bsd@bsdhome.com>	* avrdude.conf.sample, config.c, config.h, config_gram.y, lexer.l:	* main.c, pgm.c, pgm.h, ppi.c, ppi.h, term.c, term.h, Makefile:	* avr.c, avr.h:	Seperate programmer operations out into a driver-like interface so	that programmers other than the direct parallel port connection can be	supported.2002-11-23  Brian S. Dean  <bsd@bsdhome.com>	* CHANGELOG, main.c, term.c:	term.c - when in interactive terminal mode and dumping memory using	         the 'dump <memtype>' command without any address information,	         and the end of memory is reached, wrap back around to zero on	         the next invocation.	CHANGELOG - describe changes	main.c - update version number	* main.c:	When getting ready to initiate communications with the AVR device,	first pull /RESET low for a short period of time before enabling the	buffer chip.  This sequence allows the AVR to be reset before the	buffer is enabled to avoid a short period of time where the AVR may be	driving the programming lines at the same time the programmer tries	to.  Of course, if a buffer is being used, then the /RESET line from	the programmer needs to be directly connected to the AVR /RESET line	and not via the buffer chip.2002-11-06  Brian S. Dean  <bsd@bsdhome.com>	* CHANGELOG: Update changelog.	* avr.c, avr.h, main.c: Fix -Y option.  Reported by Joerg Wunsch.2002-11-01  Brian S. Dean  <bsd@bsdhome.com>	* CHANGELOG, main.c: Version update and CHANGELOG entry.	* avr.c:	Be backward compatible with the 2-byte rewrite cycle counter which	appeared in version 2.1.0, but was changed to a 4 byte counter in	version 2.1.1.  Reminded by Joerg Wunsch.2002-10-29  Brian S. Dean  <bsd@bsdhome.com>	* CHANGELOG, avrdude.1, main.c:	Add '-V' (no verify) flag requested by Joerg Wunsch.  Update the man	page.2002-10-13  Brian S. Dean  <bsd@bsdhome.com>	* CHANGELOG, avrdude.1: Update man page and changelog.	* main.c: Update version number.2002-10-12  Brian S. Dean  <bsd@bsdhome.com>	* Makefile: Remove --pedantic and -g from the compiler options.2002-10-11  Brian S. Dean  <bsd@bsdhome.com>	* avr.c, term.c:	Use a four byte value instead of a two byte value for the programming	cycle count stored at the end of EEPROM.  It seems as though Atmel was	greatly conservative in claiming a 1000 count reliability for the	FLASH.  I current have a part that has been reprogrammed 173330 times,	and counting.	Fix a compiler warning.	* avrdude.conf.sample:	Fix ATMega128 instruction encoding for reading the low and high fuse	bits.  Thanks to Joerg Wunsch for tripping over this.2002-08-01  Brian S. Dean  <bsd@bsdhome.com>	* avr.c, avrdude.1, main.c:	Move erase-rewrite cycle increment to within the chip erase routine so	that it is tracked no matter where the erase was initiated: command	line mode or interactive mode, without code duplicaiton.	* CHANGELOG: Recent updates.	* avr.c: Eliminate unused variables.	* avr.c, avr.h, avrdude.1, fileio.c, main.c:	Implement a way of tracking how many erase-rewrite cycles a part has	undergone.  This utilizes the last two bytes of EEPROM to maintain a	counter that is incremented each time the part is erased.2002-07-27  Brian S. Dean  <bsd@bsdhome.com>	* avr.c, main.c:	Fix a typo in a comment.  Display the size of memory being written.	Display the correct memory name in an error message (previously	hardcoded).2002-06-22  Brian S. Dean  <bsd@bsdhome.com>	* CHANGELOG, avrdude.conf.sample:	Add support for ATtiny15 - contributed by Asher Hoskins	<asher@crumbly.freeserve.co.uk>2002-04-23  Brian S. Dean  <bsd@bsdhome.com>	* CHANGELOG: Say what changed.2002-04-07  Brian S. Dean  <bsd@bsdhome.com>	* Makefile, avrdude.conf.sample:	Backup the config file to a timestamped name to keep from possibly	overwriting user-modified configs.	Add read/write instructions for all memory types for ATMEGA103,	ATMEGA128, ATMEGA16, and ATMEGA8.2002-04-05  Brian S. Dean  <bsd@bsdhome.com>	* avrdude.conf.sample:	Add support for ATMEGA128; untested; requested by Jeff Gardner	<gardner@journey.com>.2002-02-15  Brian S. Dean  <bsd@bsdhome.com>	* avrdude.conf.sample: Minor ordering.	* CHANGELOG, main.c: Update version numbers.2002-02-14  Brian S. Dean  <bsd@bsdhome.com>	* CHANGELOG: Summarize latest updates.	* avrdude.conf.sample, config_gram.y:	Make pwroff_after_write a yes/no field instead of a numeric.	* avrdude.conf.sample: Document the pwroff_after_write flag.	* avr.c: Enable the extra part verbosity when verbosity >= 3.	* avr.c, avr.h, avrdude.conf.sample, config_gram.y, lexer.l:	* main.c, term.c:	Fix error reporting by avr_write_byte().	Fix setting of status LEDs under various write-fail conditions.	Add a flag to indicate that a memory type requires the device to	possibly be powered off and back on after a write to it.  This is due	to a hardware problem on some Atmel devices, see:		http://www.atmel.com/atmel/acrobat/doc1280.pdf	Add greater verbosity to the part-display code when verbose>1 to	display avrprog's encoding of the defined programming instructions.	This is primarily for debugging purposes.	Part updates:	  * add the AT90S4414 part	  * add fuse and lock bit access instructions for the AT90S1200,	    AT90S4434, and AT90S8515.	  * add the pwroff_after_write flag to the fuse bits for the AT90S2333	    and AT90S4433 parts2002-02-09  Brian S. Dean  <bsd@bsdhome.com>	* avrdude.conf.sample:	Updates to the 2333 and 4433 parts, contributed by Joerg Wunsh.2002-01-18  Brian S. Dean  <bsd@bsdhome.com>	* CHANGELOG: Add changelog.2002-01-12  Brian S. Dean  <bsd@bsdhome.com>	* main.c: Add (c) to copyright.	* fileio.c, fileio.h, lexer.l, lists.c, lists.h, main.c:	* pindefs.h, ppi.c, ppi.h, term.c, term.h, avr.c, avr.h:	* config.c, config.h, config_gram.y:	Update version number.  Update copyright.	* avrdude.1: Update copyright and add description of "default".	Submitted by: Joerg Wunsch <j@uriah.heep.sax.de>	* avr.c, term.c:	Fix programming of write-only memories (such as lock bits on the	2313).