/* * SpanDSP - a series of DSP components for telephony * * v29tx.h - ITU V.29 modem transmit part * * Written by Steve Underwood <steveu@coppice.org> * * Copyright (C) 2003 Steve Underwood * * All rights reserved. * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2, as * published by the Free Software Foundation. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. * * $Id: v29tx.h,v 1.28 2007/05/12 12:25:39 steveu Exp $ *//*! \file */#if !defined(_SPANDSP_V29TX_H_)#define _SPANDSP_V29TX_H_/*! \page v29tx_page The V.29 transmitter\section v29tx_page_sec_1 What does it do?The V.29 transmitter implements the transmit side of a V.29 modem. This canoperate at data rates of 9600, 7200 and 4800 bits/s. The audio output is astream of 16 bit samples, at 8000 samples/second. The transmit and receive sideof V.29 modems operate independantly. V.29 is mostly used for FAX transmission,where it provides the standard 9600 and 7200 bits/s rates (the 4800 bits/s modeis not used for FAX). \section v29tx_page_sec_2 How does it work?V.29 uses QAM modulation. The standard method of producing a QAM modulatedsignal is to use a sampling rate which is a multiple of the baud rate. The rawsignal is then a series of complex pulses, each an integer number of sampleslong. These can be shaped, using a suitable complex filter, and multiplied by acomplex carrier signal to produce the final QAM signal for transmission. The pulse shaping filter is only vaguely defined by the V.29 spec. Some of theother ITU modem specs. fully define the filter, typically specifying a rootraised cosine filter, with 50% excess bandwidth. This is a pity, since itincreases the variability of the received signal. However, the receiver'sadaptive equalizer will compensate for these differences. The currentdesign uses a root raised cosine filter with 25% excess bandwidth. Greaterexcess bandwidth will not allow the tranmitted signal to meet the spectralrequirements.The sampling rate for our transmitter is defined by the channel - 8000 persecond. This is not a multiple of the baud rate (i.e. 2400 baud). The baudinterval is actually 10/3 sample periods. Instead of using a symmetricFIR to pulse shape the signal, a polyphase filter is used. This consists of10 sets of coefficients, offering zero to 9/10ths of a baud phase shift as wellas root raised cosine filtering. The appropriate coefficient set is chosen foreach signal sample generated.The carrier is generated using the DDS method. Using two second order resonators,started in quadrature, might be more efficient, as it would have less impact onthe processor cache than a table lookup approach. However, the DDS approachsuits the receiver better, so the same signal generator is also used for thetransmitter. The equation defining QAM modulation is:    s(n) = A*cos(2*pi*f*n + phi(n))where phi(n) is the phase of the information, and A is the amplitude of the informationusing the identity    cos(x + y) = cos(x)*cos(y) - sin(x)*sin(y)    we get    s(n) = A {cos(2*pi*f*n)*cos(phi(n)) - sin(2*pi*f*n)*sin(phi(n))}    substituting with the constellation positions    I(n) = A*cos(phi(n))    Q(n) = A*sin(phi(n))    gives    s(n) = I(n)*cos(2*pi*f*n) - Q(n)*sin(2*pi*f*n)*/#define V29_TX_FILTER_STEPS     9/*!    V.29 modem transmit side descriptor. This defines the working state for a    single instance of a V.29 modem transmitter.*/typedef struct{    /*! \brief The bit rate of the modem. Valid values are 4800, 7200 and 9600. */    int bit_rate;    /*! \brief The callback function used to get the next bit to be transmitted. */    get_bit_func_t get_bit;    /*! \brief A user specified opaque pointer passed to the callback function. */    void *user_data;    /*! \brief Gain required to achieve the specified output power, not allowing               for the size of the current constellation. */    float base_gain;    /*! \brief Gain required to achieve the specified output power, allowing               for the size of the current constellation. */#if defined(USE_FIXED_POINT)    int32_t gain;#else    float gain;#endif    /*! \brief The route raised cosine (RRC) pulse shaping filter buffer. */#if defined(USE_FIXED_POINT)    complexi16_t rrc_filter[2*V29_TX_FILTER_STEPS];#else    complexf_t rrc_filter[2*V29_TX_FILTER_STEPS];#endif    /*! \brief Current offset into the RRC pulse shaping filter buffer. */    int rrc_filter_step;    /*! \brief The register for the data scrambler. */    unsigned int scramble_reg;    /*! \brief The register for the training scrambler. */    uint8_t training_scramble_reg;    /*! \brief TRUE if transmitting the training sequence, or shutting down transmission.               FALSE if transmitting user data. */    int in_training;    /*! \brief A counter used to track progress through sending the training sequence. */    int training_step;    /*! \brief An offset value into the table of training parameters, used to match the               training pattern to the bit rate. */    int training_offset;    /*! \brief The current phase of the carrier (i.e. the DDS parameter). */    uint32_t carrier_phase;    /*! \brief The update rate for the phase of the carrier (i.e. the DDS increment). */    int32_t carrier_phase_rate;    /*! \brief The current fractional phase of the baud timing. */    int baud_phase;    /*! \brief The code number for the current position in the constellation. */    int constellation_state;    /*! \brief The get_bit function in use at any instant. */    get_bit_func_t current_get_bit;    /*! \brief Error and flow logging control */    logging_state_t logging;} v29_tx_state_t;#if defined(__cplusplus)extern "C"{#endif/*! Adjust a V.29 modem transmit context's power output.    \brief Adjust a V.29 modem transmit context's output power.    \param s The modem context.    \param power The power level, in dBm0 */void v29_tx_power(v29_tx_state_t *s, float power);/*! Initialise a V.29 modem transmit context. This must be called before the first    use of the context, to initialise its contents.    \brief Initialise a V.29 modem transmit context.    \param s The modem context.    \param rate The bit rate of the modem. Valid values are 4800, 7200 and 9600.    \param tep TRUE is the optional TEP tone is to be transmitted.    \param get_bit The callback routine used to get the data to be transmitted.    \param user_data An opaque pointer.    \return A pointer to the modem context, or NULL if there was a problem. */v29_tx_state_t *v29_tx_init(v29_tx_state_t *s, int rate, int tep, get_bit_func_t get_bit, void *user_data);/*! Reinitialise an existing V.29 modem transmit context, so it may be reused.    \brief Reinitialise an existing V.29 modem transmit context.    \param s The modem context.    \param rate The bit rate of the modem. Valid values are 4800, 7200 and 9600.    \param tep TRUE is the optional TEP tone is to be transmitted.    \return 0 for OK, -1 for bad parameter */int v29_tx_restart(v29_tx_state_t *s, int rate, int tep);/*! Release a V.29 modem transmit context.    \brief Release a V.29 modem transmit context.    \param s The modem context.    \return 0 for OK */int v29_tx_release(v29_tx_state_t *s);/*! Change the get_bit function associated with a V.29 modem transmit context.    \brief Change the get_bit function associated with a V.29 modem transmit context.    \param s The modem context.    \param get_bit The callback routine used to get the data to be transmitted.    \param user_data An opaque pointer. */void v29_tx_set_get_bit(v29_tx_state_t *s, get_bit_func_t get_bit, void *user_data);/*! Generate a block of V.29 modem audio samples.    \brief Generate a block of V.29 modem audio samples.    \param s The modem context.    \param amp The audio sample buffer.    \param len The number of samples to be generated.    \return The number of samples actually generated.*/int v29_tx(v29_tx_state_t *s, int16_t *amp, int len);#if defined(__cplusplus)}#endif#endif/*- End of file ------------------------------------------------------------*/