;*************************************************************************** ;
;
;	ncrt0.a30	C COMPILER for M16C/60
;
;		NC30 startup program customized for the M30245
;		microcontroller.  This program is applicable when 
;		using the basic I/O library.
;
;		Revised: 2-27-2002
;       
;       Copyright 2002 MITSUBISHI ELECTRIC & ELECTRONICS USA, INC.
;       All Rights Reserved.
;
;***************************************************************************

;---------------------------------------------------------------------
; HEEP SIZE definition	 
;	(set to 0 if not using memory management functions(calloc,malloc))
;---------------------------------------------------------------------
HEAPSIZE	.equ	300h

;---------------------------------------------------------------------
; STACK SIZE definition
;---------------------------------------------------------------------
STACKSIZE	.equ	300h

;---------------------------------------------------------------------
; INTERRUPT STACK SIZE definition
;---------------------------------------------------------------------
ISTACKSIZE	.equ	300h

;---------------------------------------------------------------------
; INTERRUPT VECTOR ADDRESS  definition
;---------------------------------------------------------------------
;VECTOR_ADR 	.equ	0ffd00h
VECTOR_ADR 	.equ	0fe000h			; use with KD30

;---------------------------------------------------------------
; special page definition
;---------------------------------------------------------------
;       macro define for special page
;
;Format:
;	SPECIAL	number
;

SPECIAL	.macro	NUM
	.org	0FFFFEH-(NUM*2)
	.glb	__SPECIAL_@NUM
	.word	__SPECIAL_@NUM  & 0FFFFH
.endm
;---------------------------------------------------------------------
; Section allocation
;---------------------------------------------------------------------
	.list OFF
	.include sect30.inc
	.list ON

;---------------------------------------------------------------------
; SBDATA area definition
;---------------------------------------------------------------------
	.glb	__SB__
__SB__	.equ	data_SE_top

;====================================================================
; Initialize Macro declaration
;---------------------------------------------------------------------
N_BZERO	.macro	TOP_ ,SECT_
	mov.b	#00H, R0L
	mov.w	#(TOP_ & 0FFFFH), A1
	mov.w	#sizeof SECT_ , R3
	sstr.b	
	.endm

N_BCOPY .macro	FROM_,TO_,SECT_
	mov.w	#(FROM_ & 0FFFFH),A0
	mov.b	#(FROM_ >>16),R1H
	mov.w	#TO_ ,A1
	mov.w	#sizeof SECT_ , R3
	smovf.b
	.endm

BZERO	.macro	TOP_,SECT_
	push.w	#sizeof SECT_ >> 16
	push.w	#sizeof SECT_  & 0ffffh
	pusha	TOP_ >>16
	pusha	TOP_ & 0ffffh
	.stk	8
	.glb	_bzero	
	.call	_bzero,G
	jsr.a	_bzero
	.endm

BCOPY	.macro	FROM_ ,TO_ ,SECT_
	push.w	#sizeof SECT_  >> 16
	push.w	#sizeof SECT_  & 0ffffh
	pusha	TO_ >>16
	pusha	TO_  & 0ffffh
	pusha	FROM_ >>16
	pusha	FROM_  & 0ffffh
	.stk	12
	.glb	_bcopy
	.call   _bcopy,G
	jsr.a	_bcopy
	.endm

;====================================================================
; Interrupt section start
;---------------------------------------------------------------------
	.insf	start,S,0
	.glb	start
	.section	interrupt
start:
;---------------------------------------------------------------------
; after reset,this program will start
;---------------------------------------------------------------------
	mov.b	#02h,0ah		;disable register protect 
	mov.b	#00h,04h		;set processor mode 
	mov.b	#00h,0ah		;enable register protect

	ldc	#0080h,	flg
	ldc	#istack_top, isp	;set istack pointer
	ldc	#stack_top, sp		;set stack pointer 
;	ldc	#stack_top, fb
	ldc	#data_SE_top, sb	;set sb register 
	ldintb	#VECTOR_ADR		;load start addr of interrupt vector table 

;====================================================================
; NEAR area initialize.
;--------------------------------------------------------------------
; bss zero clear
;--------------------------------------------------------------------
	N_BZERO	bss_SE_top,bss_SE
	N_BZERO	bss_SO_top,bss_SO
	N_BZERO	bss_NE_top,bss_NE
	N_BZERO	bss_NO_top,bss_NO

;---------------------------------------------------------------------
; initialize data section
;---------------------------------------------------------------------
	N_BCOPY data_SEI_top,data_SE_top,data_SE
	N_BCOPY	data_SOI_top,data_SO_top,data_SO
	N_BCOPY	data_NEI_top,data_NE_top,data_NE
	N_BCOPY	data_NOI_top,data_NO_top,data_NO

;====================================================================
; FAR area initialize.	   (not needed in single chip mode)
;---------------------------------------------------------------------
; bss zero clear
;---------------------------------------------------------------------
	BZERO	bss_FE_top,bss_FE
	BZERO	bss_FO_top,bss_FO
;---------------------------------------------------------------------
; Copy data_FE(FO) section from data_IFE(IFO) section
;---------------------------------------------------------------------
	BCOPY	data_FEI_top,data_FE_top,data_FE
	BCOPY	data_FOI_top,data_FO_top,data_FO

	ldc	#stack_top,sp
	.stk	-40

;====================================================================
; heap area initialize
;	(remove if not using memory management functions(calloc,malloc))
;---------------------------------------------------------------------
	.glb	__mbase
	.glb	__mnext
	.glb	__msize
	mov.w	#(heap_top&0FFFFH), __mbase
	mov.w	#(heap_top>>16), __mbase+2
	mov.w	#(heap_top&0FFFFH), __mnext
	mov.w	#(heap_top>>16), __mnext+2
	mov.w	#(HEAPSIZE&0FFFFH), __msize
	mov.w	#(HEAPSIZE>>16), __msize+2

;====================================================================
; Initialize standard I/O
;---------------------------------------------------------------------
	.glb	_init
	.call	_init,G
	jsr.a	_init

;====================================================================
; Call main() function
;---------------------------------------------------------------------
	ldc	#0h,fb	; for debuger

	.glb	_main
	jsr.a	_main

;====================================================================
; exit() function
;---------------------------------------------------------------------
	.glb	_exit
	.glb	$exit
_exit:			   ; End program
$exit:
	jmp	_exit
	.einsf
;====================================================================
; dummy interrupt function
;---------------------------------------------------------------------
dummy_int:
	reit

	.end
;***************************************************************************
;	ncrt0.a30
;
;       Copyright 2002 MITSUBISHI ELECTRIC & ELECTRONICS USA, INC.
;		All Rights Reserved.
;***************************************************************************