?? sincos.vhd
字號:
--------------------------------------------------------------------------------
-- Company: 海軍航空工程學院
-- Engineer: 呂兆康
--
-- Create Date: 22:01:52 05/05/09
-- Design Name:
-- Module Name: sincos - Behavioral
-- Project Name:
-- Target Device:
-- Tool versions:
-- Description:
--
-- Dependencies:
--
-- Revision:
-- Revision 0.01 - File Created
-- Additional Comments:
--
--------------------------------------------------------------------------------
library IEEE;
use IEEE.STD_LOGIC_1164.ALL;
use IEEE.STD_LOGIC_ARITH.ALL;
use IEEE.STD_LOGIC_UNSIGNED.ALL;
---- Uncomment the following library declaration if instantiating
---- any Xilinx primitives in this code.
--library UNISIM;
--use UNISIM.VComponents.all;
entity sincos is
Port ( clk : in std_logic;
mst_rst : out std_logic;
d : out std_logic_vector(7 downto 0);
a : out std_logic_vector(5 downto 0);
wrb : out std_logic;
io_ud : out std_logic);
end sincos;
architecture Behavioral of sincos is
signal data_tmp :std_logic_vector(7 downto 0); --數據寄存器
signal address_tmp :std_logic_vector(5 downto 0); --地址寄存器
signal cl :std_logic; --輸出時鐘
signal count:std_logic_vector(5 downto 0); --時鐘計數器
signal dount:std_logic_vector(5 downto 0); --數據計數器
begin
cl<=clk;
wrb<=not cl;
process(clk)
begin
if(clk'event and clk='1')then
if(count=36)then
count<="000000";
else
count<=count+'1';
end if;
end if;
end process;
process(clk)
begin
if(clk'event and clk='1')then
if(dount<=2)then
mst_rst<='1';
dount<=dount+'1';
else
mst_rst<='0';
end if;
end if;
end process;
process(clk)
begin
if(clk'event and clk='1')then
if count=16 then io_ud<='1';else io_ud<='0'; end if;
if count=4 then address_tmp<="000100"; data_tmp<="00000011"; --12.25MHZ此時的頻點比較穩定,波形也還可以,選用這里的頻率控制字可行
elsif count=5 then address_tmp<="000101"; data_tmp<="11011101";
elsif count=6 then address_tmp<="000110"; data_tmp<="11111101";
elsif count=7 then address_tmp<="000111"; data_tmp<="11010101";
elsif count=8 then address_tmp<="001000"; data_tmp<="01010101";
elsif count=9 then address_tmp<="001001"; data_tmp<="01010101";
elsif count=10 then address_tmp<="011101"; data_tmp<="00010100";
elsif count=11 then address_tmp<="011110"; data_tmp<="01001010";
elsif count=12 then address_tmp<="011111"; data_tmp<="00000000";
elsif count=13 then address_tmp<="100000"; data_tmp<="01000000";
end if;
d<=data_tmp;
a<=address_tmp;
end if;
end process;
end Behavioral;
?? 快捷鍵說明
復制代碼
Ctrl + C
搜索代碼
Ctrl + F
全屏模式
F11
切換主題
Ctrl + Shift + D
顯示快捷鍵
?
增大字號
Ctrl + =
減小字號
Ctrl + -