/*****************************************************************************//* *	crt0_ram.S -- startup code for Feith SCALES board. * *	(C) Copyright 1999-2002, Greg Ungerer (gerg@snapgear.com). *	(C) Copyright 2000, Lineo (www.lineo.com). *//*****************************************************************************/#include <linux/config.h>#include <linux/threads.h>#include <linux/linkage.h>#include <asm/segment.h>#include <asm/coldfire.h>#include <asm/mcfsim.h>/*****************************************************************************//* *	Feith ColdFire SCALES, chip select and memory setup. */#define	MEM_BASE	0x00000000	/* Memory base at address 0 */#define	VBR_BASE	MEM_BASE	/* Vector address */#define MEM_SIZE  0x02000000      /* Memory size 32Mb *//*****************************************************************************/.global	_start.global _rambase.global _ramvec.global	_ramstart.global	_ramend/*****************************************************************************/.data/* *	Set up the usable of RAM stuff. Size of RAM is determined then *	an initial stack set up at the end. */_rambase:.long	0_ramvec:.long	0_ramstart:.long	0_ramend:.long	0/*****************************************************************************/.text/* *	This is the codes first entry point. This is where it all *	begins... */_start:	nop					/* Filler */	move.w	#0x2700, %sr			/* No interrupts */	/*	 * Setup VBR here, otherwise buserror remap will not work.	 * if dBug was active before (on my SBC with dBug 1.1 of Dec 16 1996)	 *	 * bkr@cut.de 19990306	 *	 * Note: this is because dBUG points VBR to ROM, making vectors read	 * only, so the bus trap can't be changed. (RS)	 */	move.l	#VBR_BASE, %a7			/* Note VBR can't be read */	movec   %a7, %VBR	move.l	%a7, _ramvec			/* Set up vector addr */	move.l	%a7, _rambase			/* Set up base RAM addr */	/*	 *	Set memory size.	 */	move.l	#MEM_SIZE, %a0	move.l	%a0, %d0			/* Mem end addr is in a0 */	move.l	%d0, %sp			/* Set up initial stack ptr */	move.l	%d0, _ramend			/* Set end ram addr */	/*	 *	Enable CPU internal cache.	 */	move.l	#0x01000000, %d0		/* Invalidate cache cmd */	movec	%d0, %CACR			/* Invalidate cache */	move.l	#0x80000100, %d0		/* Setup cache mask */	movec	%d0, %CACR			/* Enable cache */	nop#ifdef CONFIG_ROMFS_FS	/*	 *	Move ROM filesystem above bss :-)	 */	lea.l	_sbss, %a0			/* Get start of bss */	lea.l	_ebss, %a1			/* Set up destination  */	move.l	%a0, %a2			/* Copy of bss start */	move.l	8(%a0), %d0			/* Get size of ROMFS */	addq.l	#8, %d0				/* Allow for rounding */	and.l	#0xfffffffc, %d0		/* Whole words */	add.l	%d0, %a0			/* Copy from end */	add.l	%d0, %a1			/* Copy from end */	move.l	%a1, _ramstart			/* Set start of ram */_copy_romfs:	move.l	-(%a0), %d0			/* Copy dword */	move.l	%d0, -(%a1)	cmp.l	%a0, %a2			/* Check if at end */	bne	_copy_romfs#else /* CONFIG_ROMFS_FS */	lea.l	_ebss, %a1	move.l	%a1, _ramstart#endif /* CONFIG_ROMFS_FS */	/*	 *	Zero out the bss region.	 */	lea.l	_sbss, %a0			/* Get start of bss */	lea.l	_ebss, %a1			/* Get end of bss */	clr.l	%d0				/* Set value */_clear_bss:	move.l	%d0, (%a0)+			/* Clear each word */	cmp.l	%a0, %a1			/* Check if at end */	bne	_clear_bss	/*	 *	Load the current thread pointer and stack.	 */	lea	init_thread_union, %a0	lea	0x2000(%a0), %sp	/*	 *	Assember start up done, start code proper.	 */	jsr	start_kernel			/* Start Linux kernel */_exit:	jmp	_exit				/* Should never get here *//*****************************************************************************/