/************************************************************/
/*		         SD Code for   M32L					        */
/*				   By   pasyong								*/
/*				   2006-4									*/
/*				   Base ICC6.31A					        */
/************************************************************/
#include <iom64v.h>
#include <macros.h>
#include "1011.h"
#define uchar unsigned char
#define uint unsigned int
#define MMC_CS_PIN     BIT(0)    //PORTB.0 
#define MMC_PORT       PORTB    

 uchar reading=0,a=0,pointer=0;
void sd_port_init()
{
MMC_PORT|=MMC_CS_PIN;
}
uchar BUFFER[512];                   //扇區緩沖區
uint i=0;
void delay_nus(uint n)
	{
	unsigned char  b;
		for (b = 1; b<n; b++)
			;
	} 
//****************************************************************************
//Send a Command to MMC/SD-Card
//Return: the second byte of response register of MMC/SD-Card
//****************************************************************************
uchar SD_Write_Command(uchar cmd,unsigned long arg)
{
   uchar tmp;
   uchar retry=0;
   
   //MMC_PORT|=MMC_CS_PIN;       //SD卡關閉   
   //send 8 Clock Impulse
   Write_Byte_SPI(0xFF);
   
   //set MMC_Chip_Select to low (MMC/SD-Card active)
  MMC_PORT&=~MMC_CS_PIN;       //SD卡使能

   Write_Byte_SPI(cmd|0x40);   //送頭命令
   Write_Byte_SPI(arg>>24);
   Write_Byte_SPI(arg>>16);     //send 6 Byte Command to MMC/SD-Card
   Write_Byte_SPI(arg>>8);
   Write_Byte_SPI(arg&0xff);
   Write_Byte_SPI(0x95);       //僅僅對RESET有效的CRC效驗碼
  
   //get 8 bit response
   //Read_Byte_MMC(); //read the first byte,ignore it. 
   do 
   {  //Only last 8 bit is used here.Read it out. 
      tmp = Read_Byte_SPI();
      retry++;
   }
   while((tmp==0xff)&&(retry<100));  //當沒有收到有效的命令的時候
   
   if(reading==0)
   MMC_PORT|=MMC_CS_PIN;            //MMC_CS_PIN=1;
   else MMC_PORT&=~MMC_CS_PIN;      //MMC_CS_PIN=0;   
   return(tmp);
}
//****************************************************************************
//SD卡初始化(SPI-MODE)
//****************************************************************************
uchar SD_Init(void)
{  
   uchar retry,temp;
   uchar i;
   MMC_PORT&=~MMC_CS_PIN;      //SD卡使能
  
  delay_nus(250);  //Wait MMC/SD ready...
   for (i=0;i<0x0f;i++) 
   {
      Write_Byte_SPI(0xff); //send 74 clock at least!!!
   }
   //Send Command CMD0 to MMC/SD Card
   retry=0;
   
   do
   { //retry 200 times to send CMD0 command 
     temp=SD_Write_Command(0,0);
     retry++;
     if(retry==100) 
     { 
      ;//CMD0 Error!
     }
   } 
   while(temp!=1);  
   
   //Send Command CMD1 to MMC/SD-Card
   retry=0;
   do
   { //retry 100 times to send CMD1 command 
     temp=SD_Write_Command(1,0);
     retry++;
     if(retry==100) 
     { 
     ;
     }
   } 
   while(temp!=0); 
   retry=0; 
    SD_Write_Command(16,512);     //設置一次讀寫B(tài)LOCK的長度為512個字節
  
   MMC_PORT|=MMC_CS_PIN;   //MMC_CS_PIN=1;  //set MMC_Chip_Select to high 
   return(0); //All commands have been taken.
} 
//****************************************************************************
//從SD卡讀一個扇區  Return 0 if no Error.
//****************************************************************************
uchar SD_Read_Block(unsigned long address)
{  
   uchar temp=0;uint i=0;
   reading=1; 
   temp=SD_Write_Command(17,address);     //讀出RESPONSE     
   while (Read_Byte_SPI()!= 0xfe)
   {;}  //直到讀取到了數據的開始頭0XFE，才繼續
   for(i=0; i<512; i++)
	{
	BUFFER[i]=Read_Byte_SPI();
	}
   Read_Byte_SPI();//CRC - Byte 
   Read_Byte_SPI();//CRC - Byte
   reading=0; 
   MMC_PORT|=MMC_CS_PIN;        //關閉SD卡
   return(temp);
}