?? net_nic.h
字號:
/*
*********************************************************************************************************
* uC/TCP-IP
* The Embedded TCP/IP Suite
*
* (c) Copyright 2003-2007; Micrium, Inc.; Weston, FL
*
* All rights reserved. Protected by international copyright laws.
*
* uC/TCP-IP is provided in source form for FREE evaluation, for educational
* use or peaceful research. If you plan on using uC/TCP-IP in a commercial
* product you need to contact Micrium to properly license its use in your
* product. We provide ALL the source code for your convenience and to help
* you experience uC/TCP-IP. The fact that the source code is provided does
* NOT mean that you can use it without paying a licensing fee.
*
* Network Interface Card (NIC) port files provided, as is, for FREE and do
* NOT require any additional licensing or licensing fee.
*
* Knowledge of the source code may NOT be used to develop a similar product.
*
* Please help us continue to provide the Embedded community with the finest
* software available. Your honesty is greatly appreciated.
*********************************************************************************************************
*/
/*
*********************************************************************************************************
*
* NETWORK INTERFACE CARD
*
* AT91RM9200 EMAC
*
* Filename : net_nic.h
* Version : V1.90
* Programmer(s) : JDH
*********************************************************************************************************
* Note(s) : (1) Supports EMAC section of Atmel's AT91RM9200 microcontroller as described in
*
* Atmel Corporation (ATMEL; http://www.atmel.com).
* (a) AT91RM9200 (ATMEL AT91RM9200; Revision 1768B-ATARM-08/03).
*
* (2) REQUIREs Ethernet Network Interface Layer located in the following network directory :
*
* \<Network Protocol Suite>\IF\Ether\
*
* where
* <Network Protocol Suite> directory path for network protocol suite
*
* (3) Since the AT91RM9200 EMAC (NIC) module is integrated into the AT91RM9200 microcontroller,
* the endianness of the registers is the same as the CPU, which is little-endian by default.
*********************************************************************************************************
*/
/*
*********************************************************************************************************
* EXTERNS
*********************************************************************************************************
*/
#ifdef NET_NIC_MODULE
#define NET_NIC_EXT
#else
#define NET_NIC_EXT extern
#endif
/*
*********************************************************************************************************
* INCLUDE FILES
*********************************************************************************************************
*/
#include <net_phy.h>
/*
*********************************************************************************************************
* DEFINES
*********************************************************************************************************
*/
/*
*********************************************************************************************************
* NIC DRIVER LAYER / ETHERNET ERROR CODES
*
* Note(s) : (1) ALL NIC-independent error codes #define'd in 'net_err.h';
* ALL AT91RM9200_EMAC-specific error codes #define'd in this 'net_nic.h'.
*
* (2) Network error code '10,000' series reserved for NIC drivers.
*********************************************************************************************************
*/
#define AT91RM9200_EMAC_ERR_RX_BUSY 10700
#define AT91RM9200_EMAC_ERR_TX_BUSY 10701
/*
*********************************************************************************************************
* GLOBAL VARIABLES
*********************************************************************************************************
*/
NET_NIC_EXT CPU_BOOLEAN NetNIC_ConnStatus; /* NIC's connection status : DEF_ON/DEF_OFF. */
#if (NET_CTR_CFG_STAT_EN == DEF_ENABLED) /* ------------------- NET DRV STATS ----------------- */
NET_NIC_EXT NET_CTR NetNIC_StatRxPktCtr;
NET_NIC_EXT NET_CTR NetNIC_StatTxPktCtr;
#endif
#if (NET_CTR_CFG_ERR_EN == DEF_ENABLED) /* ------------------- NET DRV ERRS ------------------ */
NET_NIC_EXT NET_CTR NetNIC_ErrRxPktDiscardedCtr;
NET_NIC_EXT NET_CTR NetNIC_ErrTxPktDiscardedCtr;
#endif
/*
*********************************************************************************************************
* FUNCTION PROTOTYPES
*********************************************************************************************************
*/
void NetNIC_Init (NET_ERR *perr);
void NetNIC_IntEn (NET_ERR *perr);
/* ------------------- STATUS FNCTS ------------------ */
CPU_BOOLEAN NetNIC_ConnStatusGet (void);
void NetNIC_ISR_Handler (void); /* Decode & handle rx/tx ISRs. */
/* --------------------- RX FNCTS -------------------- */
CPU_INT16U NetNIC_RxPktGetSize (void); /* Get NIC rx pkt size. */
void NetNIC_RxPkt (void *ppkt, /* Rx pkt from NIC. */
CPU_INT16U size,
NET_ERR *perr);
void NetNIC_RxPktDiscard (CPU_INT16U size, /* Discard rx pkt in NIC. */
NET_ERR *perr);
/* --------------------- TX FNCTS -------------------- */
void NetNIC_TxPktPrepare (void *ppkt,
CPU_INT16U size,
NET_ERR *perr);
void NetNIC_TxPkt (void *ppkt,
CPU_INT16U size,
NET_ERR *perr);
/* ------------------- PHYTER FNCTS ------------------ */
void NetNIC_PhyInit (NET_ERR *perr);
CPU_INT16U NetNIC_PhyRegRd (CPU_INT08U phy,
CPU_INT08U reg,
NET_ERR *perr);
void NetNIC_PhyRegWr (CPU_INT08U phy,
CPU_INT08U reg,
CPU_INT16U val,
NET_ERR *perr);
/*
*********************************************************************************************************
* FUNCTION PROTOTYPES
* DEFINED IN OS'S net_os.c
*********************************************************************************************************
*/
void NetOS_NIC_Init (NET_ERR *perr); /* Create Drv objs & start Drv tasks. */
void NetOS_NIC_TxRdyWait (NET_ERR *perr); /* Wait on drv tx empty signal from NIC. */
void NetOS_NIC_TxRdySignal (void); /* Post drv tx empty signal from NIC. */
/*
*********************************************************************************************************
* FUNCTION PROTOTYPES
* DEFINED IN PRODUCT'S net_bsp.c
*********************************************************************************************************
*/
#if (NET_NIC_CFG_RD_WR_SEL == NET_NIC_RD_WR_SEL_FNCT)
CPU_INT32U AT91RM9200_EMAC_RegRd (CPU_INT32U reg_offset);
void AT91RM9200_EMAC_RegWr (CPU_INT32U reg_offset,
CPU_INT32U val);
#endif
void AT91RM9200_EMAC_PhyRegDly(void);
/*
*********************************************************************************************************
* FUNCTION PROTOTYPES
* DEFINED IN PRODUCT's net_isr_a.s
*********************************************************************************************************
*/
void NetNIC_ISR (void);
/*
*********************************************************************************************************
* FUNCTION PROTOTYPES
* DEFINED IN PRODUCT'S net_isr.c
*
* Note(s) : (1) See this 'net_nic.c AT91RM9200_EMAC_Init() Note #5'.
*
* (2) See this 'net_nic.c NetNIC_ISR_Handler() Note #3'.
*********************************************************************************************************
*/
#if (NET_NIC_CFG_INT_CTRL_EN == DEF_ENABLED)
void NetNIC_IntInit (void); /* Init int ctrl'r [see Note #1]. */
void NetNIC_IntClr (void); /* Clr int ctrl'r src(s) [see Note #2]. */
#endif
/*
*********************************************************************************************************
* CONFIGURATION ERRORS
*********************************************************************************************************
*/
#ifndef NET_NIC_CFG_INT_CTRL_EN
#error "NET_NIC_CFG_INT_CTRL_EN not #define'd in 'net_cfg.h'"
#error " [MUST be DEF_DISABLED]"
#error " [ || DEF_ENABLED ]"
#elif ((NET_NIC_CFG_INT_CTRL_EN != DEF_DISABLED) && \
(NET_NIC_CFG_INT_CTRL_EN != DEF_ENABLED ))
#error "NET_NIC_CFG_INT_CTRL_EN illegally #define'd in 'net_cfg.h'"
#error " [MUST be DEF_DISABLED]"
#error " [ || DEF_ENABLED ]"
#endif
#ifndef AT91RM9200_EMAC_CFG_MAC_ADDR_SEL
#error "AT91RM9200_EMAC_CFG_MAC_ADDR_SEL not #define'd in 'app_cfg.h'"
#error " [MUST be AT91RM9200_EMAC_MAC_ADDR_SEL_CFG ]"
#error " [ || AT91RM9200_EMAC_MAC_ADDR_SEL_EEPROM]"
#elif ((AT91RM9200_EMAC_CFG_MAC_ADDR_SEL != AT91RM9200_EMAC_MAC_ADDR_SEL_CFG ) && \
(AT91RM9200_EMAC_CFG_MAC_ADDR_SEL != AT91RM9200_EMAC_MAC_ADDR_SEL_EEPROM))
#error "AT91RM9200_EMAC_CFG_MAC_ADDR_SEL illegally #define'd in 'app_cfg.h'"
#error " [MUST be AT91RM9200_EMAC_MAC_ADDR_SEL_CFG ]"
#error " [ || AT91RM9200_EMAC_MAC_ADDR_SEL_EEPROM]"
#endif
#ifndef AT91RM9200_EMAC_RX_NUM_BUFS
#error "AT91RM9200_EMAC_RX_NUM_BUFS not #define'd in 'net_bsp.h'"
#error " [MUST be >= 2]"
#elif (AT91RM9200_EMAC_RX_NUM_BUFS < 2)
#error "AT91RM9200_EMAC_RX_NUM_BUFS illegally #define'd in 'net_bsp.h'"
#error " [MUST be >= 2]"
#endif
#ifndef AT91RM9200_EMAC_RX_BUF_HDRS_ADDR
#error "AT91RM9200_EMAC_RX_BUF_HDRS_ADDR not #define'd in 'net_bsp.h'"
#endif
#ifndef AT91RM9200_EMAC_RX_BUF_ADDR
#error "AT91RM9200_EMAC_RX_BUF_ADDR not #define'd in 'net_bsp.h'"
#endif
#ifndef AT91RM9200_EMAC_TX_BUF_ADDR
#error "AT91RM9200_EMAC_TX_BUF_ADDR not #define'd in 'net_bsp.h'"
#endif
#if (NET_NIC_CFG_TX_PKT_PREPARE_EN != DEF_ENABLED)
#error "NET_NIC_CFG_TX_PKT_PREPARE_EN MUST be enabled with this driver."
#endif
?? 快捷鍵說明
復制代碼
Ctrl + C
搜索代碼
Ctrl + F
全屏模式
F11
切換主題
Ctrl + Shift + D
顯示快捷鍵
?
增大字號
Ctrl + =
減小字號
Ctrl + -