?? at91rm9200.h
字號:
} AT91S_SPI, *AT91PS_SPI;
// -------- SPI_CR : (SPI Offset: 0x0) SPI Control Register --------
#define AT91C_SPI_SPIEN ((unsigned int) 0x1 << 0) // (SPI) SPI Enable
#define AT91C_SPI_SPIDIS ((unsigned int) 0x1 << 1) // (SPI) SPI Disable
#define AT91C_SPI_SWRST ((unsigned int) 0x1 << 7) // (SPI) SPI Software reset
// -------- SPI_MR : (SPI Offset: 0x4) SPI Mode Register --------
#define AT91C_SPI_MSTR ((unsigned int) 0x1 << 0) // (SPI) Master/Slave Mode
#define AT91C_SPI_PS ((unsigned int) 0x1 << 1) // (SPI) Peripheral Select
#define AT91C_SPI_PS_FIXED ((unsigned int) 0x0 << 1) // (SPI) Fixed Peripheral Select
#define AT91C_SPI_PS_VARIABLE ((unsigned int) 0x1 << 1) // (SPI) Variable Peripheral Select
#define AT91C_SPI_PCSDEC ((unsigned int) 0x1 << 2) // (SPI) Chip Select Decode
#define AT91C_SPI_DIV32 ((unsigned int) 0x1 << 3) // (SPI) Clock Selection
#define AT91C_SPI_MODFDIS ((unsigned int) 0x1 << 4) // (SPI) Mode Fault Detection
#define AT91C_SPI_LLB ((unsigned int) 0x1 << 7) // (SPI) Clock Selection
#define AT91C_SPI_PCS ((unsigned int) 0xF << 16) // (SPI) Peripheral Chip Select
#define AT91C_SPI_DLYBCS ((unsigned int) 0xFF << 24) // (SPI) Delay Between Chip Selects
// -------- SPI_RDR : (SPI Offset: 0x8) Receive Data Register --------
#define AT91C_SPI_RD ((unsigned int) 0xFFFF << 0) // (SPI) Receive Data
#define AT91C_SPI_RPCS ((unsigned int) 0xF << 16) // (SPI) Peripheral Chip Select Status
// -------- SPI_TDR : (SPI Offset: 0xc) Transmit Data Register --------
#define AT91C_SPI_TD ((unsigned int) 0xFFFF << 0) // (SPI) Transmit Data
#define AT91C_SPI_TPCS ((unsigned int) 0xF << 16) // (SPI) Peripheral Chip Select Status
// -------- SPI_SR : (SPI Offset: 0x10) Status Register --------
#define AT91C_SPI_RDRF ((unsigned int) 0x1 << 0) // (SPI) Receive Data Register Full
#define AT91C_SPI_TDRE ((unsigned int) 0x1 << 1) // (SPI) Transmit Data Register Empty
#define AT91C_SPI_MODF ((unsigned int) 0x1 << 2) // (SPI) Mode Fault Error
#define AT91C_SPI_OVRES ((unsigned int) 0x1 << 3) // (SPI) Overrun Error Status
#define AT91C_SPI_SPENDRX ((unsigned int) 0x1 << 4) // (SPI) End of Receiver Transfer
#define AT91C_SPI_SPENDTX ((unsigned int) 0x1 << 5) // (SPI) End of Receiver Transfer
#define AT91C_SPI_RXBUFF ((unsigned int) 0x1 << 6) // (SPI) RXBUFF Interrupt
#define AT91C_SPI_TXBUFE ((unsigned int) 0x1 << 7) // (SPI) TXBUFE Interrupt
#define AT91C_SPI_SPIENS ((unsigned int) 0x1 << 16) // (SPI) Enable Status
// -------- SPI_IER : (SPI Offset: 0x14) Interrupt Enable Register --------
// -------- SPI_IDR : (SPI Offset: 0x18) Interrupt Disable Register --------
// -------- SPI_IMR : (SPI Offset: 0x1c) Interrupt Mask Register --------
// -------- SPI_CSR : (SPI Offset: 0x30) Chip Select Register --------
#define AT91C_SPI_CPOL ((unsigned int) 0x1 << 0) // (SPI) Clock Polarity
#define AT91C_SPI_NCPHA ((unsigned int) 0x1 << 1) // (SPI) Clock Phase
#define AT91C_SPI_BITS ((unsigned int) 0xF << 4) // (SPI) Bits Per Transfer
#define AT91C_SPI_BITS_8 ((unsigned int) 0x0 << 4) // (SPI) 8 Bits Per transfer
#define AT91C_SPI_BITS_9 ((unsigned int) 0x1 << 4) // (SPI) 9 Bits Per transfer
#define AT91C_SPI_BITS_10 ((unsigned int) 0x2 << 4) // (SPI) 10 Bits Per transfer
#define AT91C_SPI_BITS_11 ((unsigned int) 0x3 << 4) // (SPI) 11 Bits Per transfer
#define AT91C_SPI_BITS_12 ((unsigned int) 0x4 << 4) // (SPI) 12 Bits Per transfer
#define AT91C_SPI_BITS_13 ((unsigned int) 0x5 << 4) // (SPI) 13 Bits Per transfer
#define AT91C_SPI_BITS_14 ((unsigned int) 0x6 << 4) // (SPI) 14 Bits Per transfer
#define AT91C_SPI_BITS_15 ((unsigned int) 0x7 << 4) // (SPI) 15 Bits Per transfer
#define AT91C_SPI_BITS_16 ((unsigned int) 0x8 << 4) // (SPI) 16 Bits Per transfer
#define AT91C_SPI_SCBR ((unsigned int) 0xFF << 8) // (SPI) Serial Clock Baud Rate
#define AT91C_SPI_DLYBS ((unsigned int) 0xFF << 16) // (SPI) Serial Clock Baud Rate
#define AT91C_SPI_DLYBCT ((unsigned int) 0xFF << 24) // (SPI) Delay Between Consecutive Transfers
// *****************************************************************************
// SOFTWARE API DEFINITION FOR Synchronous Serial Controller Interface
// *****************************************************************************
typedef struct _AT91S_SSC {
AT91_REG SSC_CR; // Control Register
AT91_REG SSC_CMR; // Clock Mode Register
AT91_REG Reserved0[2]; //
AT91_REG SSC_RCMR; // Receive Clock ModeRegister
AT91_REG SSC_RFMR; // Receive Frame Mode Register
AT91_REG SSC_TCMR; // Transmit Clock Mode Register
AT91_REG SSC_TFMR; // Transmit Frame Mode Register
AT91_REG SSC_RHR; // Receive Holding Register
AT91_REG SSC_THR; // Transmit Holding Register
AT91_REG Reserved1[2]; //
AT91_REG SSC_RSHR; // Receive Sync Holding Register
AT91_REG SSC_TSHR; // Transmit Sync Holding Register
AT91_REG SSC_RC0R; // Receive Compare 0 Register
AT91_REG SSC_RC1R; // Receive Compare 1 Register
AT91_REG SSC_SR; // Status Register
AT91_REG SSC_IER; // Interrupt Enable Register
AT91_REG SSC_IDR; // Interrupt Disable Register
AT91_REG SSC_IMR; // Interrupt Mask Register
AT91_REG Reserved2[44]; //
AT91_REG SSC_RPR; // Receive Pointer Register
AT91_REG SSC_RCR; // Receive Counter Register
AT91_REG SSC_TPR; // Transmit Pointer Register
AT91_REG SSC_TCR; // Transmit Counter Register
AT91_REG SSC_RNPR; // Receive Next Pointer Register
AT91_REG SSC_RNCR; // Receive Next Counter Register
AT91_REG SSC_TNPR; // Transmit Next Pointer Register
AT91_REG SSC_TNCR; // Transmit Next Counter Register
AT91_REG SSC_PTCR; // PDC Transfer Control Register
AT91_REG SSC_PTSR; // PDC Transfer Status Register
} AT91S_SSC, *AT91PS_SSC;
// -------- SSC_CR : (SSC Offset: 0x0) SSC Control Register --------
#define AT91C_SSC_RXEN ((unsigned int) 0x1 << 0) // (SSC) Receive Enable
#define AT91C_SSC_RXDIS ((unsigned int) 0x1 << 1) // (SSC) Receive Disable
#define AT91C_SSC_TXEN ((unsigned int) 0x1 << 8) // (SSC) Transmit Enable
#define AT91C_SSC_TXDIS ((unsigned int) 0x1 << 9) // (SSC) Transmit Disable
#define AT91C_SSC_SWRST ((unsigned int) 0x1 << 15) // (SSC) Software Reset
// -------- SSC_RCMR : (SSC Offset: 0x10) SSC Receive Clock Mode Register --------
#define AT91C_SSC_CKS ((unsigned int) 0x3 << 0) // (SSC) Receive/Transmit Clock Selection
#define AT91C_SSC_CKS_DIV ((unsigned int) 0x0) // (SSC) Divided Clock
#define AT91C_SSC_CKS_TK ((unsigned int) 0x1) // (SSC) TK Clock signal
#define AT91C_SSC_CKS_RK ((unsigned int) 0x2) // (SSC) RK pin
#define AT91C_SSC_CKO ((unsigned int) 0x7 << 2) // (SSC) Receive/Transmit Clock Output Mode Selection
#define AT91C_SSC_CKO_NONE ((unsigned int) 0x0 << 2) // (SSC) Receive/Transmit Clock Output Mode: None RK pin: Input-only
#define AT91C_SSC_CKO_CONTINOUS ((unsigned int) 0x1 << 2) // (SSC) Continuous Receive/Transmit Clock RK pin: Output
#define AT91C_SSC_CKO_DATA_TX ((unsigned int) 0x2 << 2) // (SSC) Receive/Transmit Clock only during data transfers RK pin: Output
#define AT91C_SSC_CKI ((unsigned int) 0x1 << 5) // (SSC) Receive/Transmit Clock Inversion
#define AT91C_SSC_CKG ((unsigned int) 0x3 << 6) // (SSC) Receive/Transmit Clock Gating Selection
#define AT91C_SSC_CKG_NONE ((unsigned int) 0x0 << 6) // (SSC) Receive/Transmit Clock Gating: None, continuous clock
#define AT91C_SSC_CKG_LOW ((unsigned int) 0x1 << 6) // (SSC) Receive/Transmit Clock enabled only if RF Low
#define AT91C_SSC_CKG_HIGH ((unsigned int) 0x2 << 6) // (SSC) Receive/Transmit Clock enabled only if RF High
#define AT91C_SSC_START ((unsigned int) 0xF << 8) // (SSC) Receive/Transmit Start Selection
#define AT91C_SSC_START_CONTINOUS ((unsigned int) 0x0 << 8) // (SSC) Continuous, as soon as the receiver is enabled, and immediately after the end of transfer of the previous data.
#define AT91C_SSC_START_TX ((unsigned int) 0x1 << 8) // (SSC) Transmit/Receive start
#define AT91C_SSC_START_LOW_RF ((unsigned int) 0x2 << 8) // (SSC) Detection of a low level on RF input
#define AT91C_SSC_START_HIGH_RF ((unsigned int) 0x3 << 8) // (SSC) Detection of a high level on RF input
#define AT91C_SSC_START_FALL_RF ((unsigned int) 0x4 << 8) // (SSC) Detection of a falling edge on RF input
#define AT91C_SSC_START_RISE_RF ((unsigned int) 0x5 << 8) // (SSC) Detection of a rising edge on RF input
#define AT91C_SSC_START_LEVEL_RF ((unsigned int) 0x6 << 8) // (SSC) Detection of any level change on RF input
#define AT91C_SSC_START_EDGE_RF ((unsigned int) 0x7 << 8) // (SSC) Detection of any edge on RF input
#define AT91C_SSC_START_0 ((unsigned int) 0x8 << 8) // (SSC) Compare 0
#define AT91C_SSC_STOP ((unsigned int) 0x1 << 12) // (SSC) Receive Stop Selection
#define AT91C_SSC_STTOUT ((unsigned int) 0x1 << 15) // (SSC) Receive/Transmit Start Output Selection
#define AT91C_SSC_STTDLY ((unsigned int) 0xFF << 16) // (SSC) Receive/Transmit Start Delay
#define AT91C_SSC_PERIOD ((unsigned int) 0xFF << 24) // (SSC) Receive/Transmit Period Divider Selection
// -------- SSC_RFMR : (SSC Offset: 0x14) SSC Receive Frame Mode Register --------
#define AT91C_SSC_DATLEN ((unsigned int) 0x1F << 0) // (SSC) Data Length
#define AT91C_SSC_LOOP ((unsigned int) 0x1 << 5) // (SSC) Loop Mode
#define AT91C_SSC_MSBF ((unsigned int) 0x1 << 7) // (SSC) Most Significant Bit First
#define AT91C_SSC_DATNB ((unsigned int) 0xF << 8) // (SSC) Data Number per Frame
#define AT91C_SSC_FSLEN ((unsigned int) 0xF << 16) // (SSC) Receive/Transmit Frame Sync length
#define AT91C_SSC_FSOS ((unsigned int) 0x7 << 20) // (SSC) Receive/Transmit Frame Sync Output Selection
#define AT91C_SSC_FSOS_NONE ((unsigned int) 0x0 << 20) // (SSC) Selected Receive/Transmit Frame Sync Signal: None RK pin Input-only
#define AT91C_SSC_FSOS_NEGATIVE ((unsigned int) 0x1 << 20) // (SSC) Selected Receive/Transmit Frame Sync Signal: Negative Pulse
#define AT91C_SSC_FSOS_POSITIVE ((unsigned int) 0x2 << 20) // (SSC) Selected Receive/Transmit Frame Sync Signal: Positive Pulse
#define AT91C_SSC_FSOS_LOW ((unsigned int) 0x3 << 20) // (SSC) Selected Receive/Transmit Frame Sync Signal: Driver Low during data transfer
#define AT91C_SSC_FSOS_HIGH ((unsigned int) 0x4 << 20) // (SSC) Selected Receive/Transmit Frame Sync Signal: Driver High during data transfer
#define AT91C_SSC_FSOS_TOGGLE ((unsigned int) 0x5 << 20) // (SSC) Selected Receive/Transmit Frame Sync Signal: Toggling at each start of data transfer
#define AT91C_SSC_FSEDGE ((unsigned int) 0x1 << 24) // (SSC) Frame Sync Edge Detection
// -------- SSC_TCMR : (SSC Offset: 0x18) SSC Transmit Clock Mode Register --------
// -------- SSC_TFMR : (SSC Offset: 0x1c) SSC Transmit Frame Mode Register --------
#define AT91C_SSC_DATDEF ((unsigned int) 0x1 << 5) // (SSC) Data Default Value
#define AT91C_SSC_FSDEN ((unsigned int) 0x1 << 23) // (SSC) Frame Sync Data Enable
// -------- SSC_SR : (SSC Offset: 0x40) SSC Status Register --------
#define AT91C_SSC_TXRDY ((unsigned int) 0x1 << 0) // (SSC) Transmit Ready
#define AT91C_SSC_TXEMPTY ((unsigned int) 0x1 << 1) // (SSC) Transmit Empty
#define AT91C_SSC_ENDTX ((unsigned int) 0x1 << 2) // (SSC) End Of Transmission
#define AT91C_SSC_TXBUFE ((unsigned int) 0x1 << 3) // (SSC) Transmit Buffer Empty
#define AT91C_SSC_RXRDY ((unsigned int) 0x1 << 4) // (SSC) Receive Ready
#define AT91C_SSC_OVRUN ((unsigned int) 0x1 << 5) // (SSC) Receive Overrun
#define AT91C_SSC_ENDRX ((unsigned int) 0x1 << 6) // (SSC) End of Reception
#define AT91C_SSC_RXBUFF ((unsigned int) 0x1 << 7) // (SSC) Receive Buffer Full
#define AT91C_SSC_CP0 ((unsigned int) 0x1 << 8) // (SSC) Compare 0
#define AT91C_SSC_CP1 ((unsigned int) 0x1 << 9) // (SSC) Compare 1
#define AT91C_SSC_TXSYN ((unsigned int) 0x1 << 10) // (SSC) Transmit Sync
#define AT91C_SSC_RXSYN ((unsigned int) 0x1 << 11) // (SSC) Receive Sync
#define AT91C_SSC_TXENA ((unsigned int) 0x1 << 16) // (SSC) Transmit Enable
#define AT91C_SSC_RXENA ((unsigned int) 0x1 << 17) // (SSC) Receive Enable
// -------- SSC_IER : (SSC Offset: 0x44) SSC Interrupt Enable Register --------
// -------- SSC_IDR : (SSC Offset: 0x48) SSC Interrupt Disable Register --------
// -------- SSC_IMR : (SSC Offset: 0x4c) SSC Interrupt Mask Register --------
// *****************************************************************************
// SOFTWARE API DEFINITION FOR Usart
// *****************************************************************************
typedef struct _AT91S_USART {
AT91_REG US_CR; // Control Register
AT91_REG US_MR; // Mode Register
AT91_REG US_IER; // Interrupt Enable Register
AT91_REG US_IDR; // Interrupt Disable Register
AT91_REG US_IMR; // Interrupt Mask Register
AT91_REG US_CSR; // Channel Status Register
AT91_REG US_RHR; // Receiver Holding Register
AT91_REG US_THR; // Transmitter Holding Register
AT91_REG US_BRGR; // Baud Rate Generator Register
AT91_REG US_RTOR; // Receiver Time-out Register
AT91_REG US_TTGR; // Transmitter Time-guard Register
AT91_REG Reserved0[5]; //
AT91_REG US_FIDI; // FI_DI_Ratio Register
AT91_REG US_NER; // Nb Errors Register
AT91_REG US_XXR; // XON_XOFF Register
AT91_REG US_IF; // IRDA_FILTER Register
AT91_REG Reserved1[44]; //
AT91_REG US_RPR; // Receive Pointer Register
AT91_REG US_RCR; // Receive Counter Register
AT91_REG US_TPR; // Transmit Pointer Register
AT91_REG US_TCR; // Transmit Counter Register
AT91_REG US_RNPR; // Receive Next Pointer Register
AT91_REG US_RNCR; // Receive Next Counter Register
AT91_REG US_TNPR; // Transmit Next Pointer Register
AT91_REG US_TNCR; // Transmit Next Counter Register
AT91_REG US_PTCR; // PDC Transfer Control Register
AT91_REG US_PTSR; // PDC Transfer Status Register
} AT91S_USART, *AT91PS_USART;
// -------- US_CR : (USART Offset: 0x0) Debug Unit Control Register --------
#define AT91C_US_RSTSTA ((unsigned int) 0x1 << 8) // (USART) Reset Status Bits
#define AT91C_US_STTBRK ((unsigned int) 0x1 << ?? 快捷鍵說明
復制代碼
Ctrl + C
搜索代碼
Ctrl + F
全屏模式
F11
切換主題
Ctrl + Shift + D
顯示快捷鍵
?
增大字號
Ctrl + =
減小字號
Ctrl + -