//*****************************************************************************
//
// qs_dk-lm3s301.c - A quick start sample application to demo chip features
//
// Copyright (c) 2006-2007 Luminary Micro, Inc.  All rights reserved.
// 
// Software License Agreement
// 
// Luminary Micro, Inc. (LMI) is supplying this software for use solely and
// exclusively on LMI's microcontroller products.
// 
// The software is owned by LMI and/or its suppliers, and is protected under
// applicable copyright laws.  All rights are reserved.  You may not combine
// this software with "viral" open-source software in order to form a larger
// program.  Any use in violation of the foregoing restrictions may subject
// the user to criminal sanctions under applicable laws, as well as to civil
// liability for the breach of the terms and conditions of this license.
// 
// THIS SOFTWARE IS PROVIDED "AS IS".  NO WARRANTIES, WHETHER EXPRESS, IMPLIED
// OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF
// MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE APPLY TO THIS SOFTWARE.
// LMI SHALL NOT, IN ANY CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL, OR
// CONSEQUENTIAL DAMAGES, FOR ANY REASON WHATSOEVER.
// 
// This is part of revision 1952 of the Stellaris Peripheral Driver Library.
//
//*****************************************************************************

#include "../../../hw_memmap.h"
#include "../../../hw_types.h"
#include "../../../src/comp.h"
#include "../../../src/debug.h"
#include "../../../src/gpio.h"
#include "../../../src/interrupt.h"
#include "../../../src/sysctl.h"
#include "../../../src/systick.h"
#include "../../../src/pwm.h"
#include "../../../src/adc.h"
#include "../../../src/uart.h"
#include "../pdc.h"

//*****************************************************************************
//
// Define I/O configuration.
//
//*****************************************************************************
#define COMPARATOR_ID   0
#define GPIO_PIN_MUTE   GPIO_PIN_5

//*****************************************************************************
//
//! \addtogroup dk_lm3s301_list
//! <h1>DK-LM3S301 Quickstart Application (qs_dk-lm3s301)</h1>
//!
//! This example uses the photocell on the development board to create a geiger
//! counter for visible light.  In bright light, the click rate (that is, the
//! count) increases; in low light it decreases.  The light reading is also
//! displayed on the LCD, and a log of the readings is output on the UART at
//! 115,200, 8-n-1.  The push button can be used to turn off the clicking noise
//! on and off; when off the LCD and UART still provide the light reading.
//!
//! In the default jumper configuration of the development board, this example
//! actually samples the potentiometer and the push button will not work.  In
//! order for this example to fully work, the following jumper wire connections
//! must be made: JP3 pin 1 to JP5 pin 2 (requiring the removal of the jumper
//! on JP5) and JP19 pin 2 to J6 pin 6.
//
//*****************************************************************************

//*****************************************************************************
//
// The voltage levels of the internal voltage reference to use for comparison
// to the photocell input.
//
//*****************************************************************************
static const unsigned long g_pulCompLevels[] =
{
    COMP_REF_0_1375V, COMP_REF_0_275V, COMP_REF_0_4125V, COMP_REF_0_55V,
    COMP_REF_0_6875V, COMP_REF_0_825V, COMP_REF_0_9625V, COMP_REF_1_1V,
    COMP_REF_1_2375V, COMP_REF_1_375V, COMP_REF_1_5125V, COMP_REF_1_65V,
    COMP_REF_1_7875V, COMP_REF_1_925V, COMP_REF_2_0625V
};

//*****************************************************************************
//
// The current index into the internal voltage reference array.
//
//*****************************************************************************
static unsigned long g_ulCompIdx;

//*****************************************************************************
//
// The current accumulation of results from the comparator.
//
//*****************************************************************************
static unsigned long g_ulCompAccum;

//*****************************************************************************
//
// The most recent setting of the potentiometer.
//
//*****************************************************************************
static unsigned long g_ulPotSetting;

//*****************************************************************************
//
// The number of SysTick counts between clicks of the piezo.
//
//*****************************************************************************
static unsigned long g_ulClickRate;

//*****************************************************************************
//
// Counts SysTick events.  Used to determine when the piezo should make a
// sound.
//
//*****************************************************************************
static unsigned long g_ulClickRateCount;

//*****************************************************************************
//
// The counter of the number of consecutive times that the push button has a
// value different than the currently debounced state.
//
//*****************************************************************************
static unsigned long g_ulDebounceCounter;

//*****************************************************************************
//
// A set of flags.  The flag bits are defined as follows:
//
//     0 -> The mute flag; when clear, the piezo will not be clicked and the
//          comparator results will only be available on the LCD and over the
//          UART.  When set, the piezo will click.
//     1 -> An indicator from the SysTick interrupt handler to the main code
//          that new comparator results are available.
//     2 -> The current debounced state of the push button.
//     3 -> An indicator that a SysTick interrupt has occurred.
//
//*****************************************************************************
#define FLAG_UNMUTE     0
#define FLAG_RESULTS    1
#define FLAG_BUTTON     2
#define FLAG_SYSTICK    3
static volatile unsigned long g_ulFlags;

//*****************************************************************************
//
// The error routine that is called if the driver library encounters an error.
//
//*****************************************************************************
#ifdef DEBUG
void
__error__(char *pcFilename, unsigned long ulLine)
{
}
#endif

//*****************************************************************************
//
// The interrupt handler for the SysTick interrupt.
//
//*****************************************************************************
void
SysTickIntHandler(void)
{
    //
    // Indicate that a SysTick interrupt has occurred.
    //
    HWREGBITW(&g_ulFlags, FLAG_SYSTICK) = 1;

    //
    // Determine the tick rate.  Get the current comparator value.  Increment
    // the accumulator if it is one.
    //
    if(ComparatorValueGet(COMP_BASE, COMPARATOR_ID))
    {
        g_ulCompAccum++;
    }

    //
    // Increment the internal reference voltage array index and see if the end
    // has been reached.
    //
    g_ulCompIdx++;
    if(g_ulCompIdx == (sizeof(g_pulCompLevels) / sizeof(g_pulCompLevels[0])))
    {
        //
        // Go back to the beginning of the array.
        //
        g_ulCompIdx = 0;

        //
        // Save the comparison results and reset the accumulator.
        //
        g_ulPotSetting = g_ulCompAccum;
        g_ulCompAccum = 0;

        //
        // Set the bit in g_ulFlags indicating that new results are available.
        //
        HWREGBITW(&g_ulFlags, FLAG_RESULTS) = 1;

        //
        // Compute the new rate at which to click the piezo.
        //
        g_ulClickRate = ((15 - g_ulPotSetting) + 3) * 5;

        //
        // If the current count is greater than the click rate then set the
        // count to the click rate so that the click will happen sooner.
        //
        if(g_ulClickRateCount > g_ulClickRate)
        {
            g_ulClickRateCount = g_ulClickRate;
        }
    }

    //
    // Set the internal reference voltage to the next comparison value.
    //
    ComparatorRefSet(COMP_BASE, g_pulCompLevels[g_ulCompIdx]);

    //
    // Determine if the piezo should be muted.  See if the push button is in a
    // different state than the currently debounced state.
    //
    if((GPIOPinRead(GPIO_PORTB_BASE, GPIO_PIN_MUTE) ? 1 : 0) !=
       HWREGBITW(&g_ulFlags, FLAG_BUTTON))
    {
        //
        // Increment the number of counts with the push button in a different
        // state.
        //
        g_ulDebounceCounter++;

        //
        // If four consecutive counts have had the push button in a different
        // state then the state has changed.
        //
        if(g_ulDebounceCounter == 4)
        {
            //
            // Toggle the debounced state of the push button.
            //
            HWREGBITW(&g_ulFlags, FLAG_BUTTON) ^= 1;

            //
            // If the push button was just pushed, then toggle the mute flag.
            //
            if(!HWREGBITW(&g_ulFlags, FLAG_BUTTON))
            {
                //
                // Toggle the mute flag.