#ifndef	__LCD_CONFIG_h__
#define	__LCD_CONFIG_h__
//	write your header here
#define LCD_X_MAX			128-1			//屏幕的X軸的物理寬度
#define LCD_Y_MAX			64-1			//屏幕的Y軸的物理寬度
			
#define LCD_XY_Switch		0				//顯示時X軸和Y由交換
#define LCD_X_Rev			0				//顯示時X軸反轉
#define LCD_Y_Rev			0				//顯示時Y軸反轉

#if LCD_XY_Switch == 0
	#define Dis_X_MAX		LCD_X_MAX
	#define Dis_Y_MAX		LCD_Y_MAX	
#endif

#if LCD_XY_Switch == 1
	#define Dis_X_MAX		LCD_Y_MAX
	#define Dis_Y_MAX		LCD_X_MAX	
#endif

#define LCD_INITIAL_COLOR	0x00ff			//定義LCD屏初始化時的背景色0x0000

//以下定義為針對于cpu的功能指令進行定義的，局部可修改~
//LCD供電電平選擇
#define		M_LCD_VDD_SET	M_LCD_SETR_7//M_LCD_SETR_5		//3.3V供電時選此二項
#define		M_LCD_VDD		M_LCD_BIAS_7//....
//#define		M_LCD_VDD_SET	M_LCD_SETR_4	//5.0V供電時選此二項
//#define		M_LCD_VDD		M_LCD_BIAS_9	//...
//LCD指令
//LCD開關命令
#define		M_LCD_ON		0x00af
#define		M_LCD_OFF		0x00ae
//設置上電控制模式
#define		M_LCD_POWER_BC	0x002c
#define		M_LCD_POWER_VR	0x002a
#define		M_LCD_POWER_VC	0x0029
#define		M_LCD_POWER_ALL	0x002f
//V5內部電壓調節電阻設置……
#define		M_LCD_SETR_0	0x0020
#define		M_LCD_SETR_1	0x0021
#define		M_LCD_SETR_2	0x0022
#define		M_LCD_SETR_3	0x0023
#define		M_LCD_SETR_4	0x0024
#define		M_LCD_SETR_5	0x0025
#define		M_LCD_SETR_6	0x0026
#define		M_LCD_SETR_7	0x0027
//...end
#define		M_LCD_ELE_VOL	0x0081		//電量設置模式（顯示亮度）
//偏壓設置
#define		M_LCD_BIAS_9	0x00a2		//V5時選此選項設置
#define		M_LCD_BIAS_7	0x00a1		//V3時選此選項設置
//Com 掃描方式設置命令
#define		M_LCD_COM_NOR	0x00c0		//正常方式
#define		M_LCD_COM_REV	0x00c8		//反相
//Segment方向選擇
#define		M_LCD_SEG_NOR	0x00a0		//正常
#define		M_LCD_SEG_REV	0x00a1		//反向
//全屏點亮/變暗指令
#define		M_LCD_ALL_LIGNT	0x00a5		//LCD ALL paint ON
#define		M_LCD_ALL_LOW	0x00a4		//Normal Display mode
//正相反相顯示控制指令，RAM中數據不變
#define		M_LCD_ALL_NOR	0x00a6		//正相
#define		M_LCD_ALL_REV	0x00a7		//反相
//靜態指示器控制指令
#define		M_LCD_STATIC_ON	0x00ad		//ON
#define		M_LCD_STATIC_OFF 0x00ac		//OFF
//設置顯示起始行對應RAM行號
#define		M_LCD_BEGIN_LINE 0x0040		//基數，后面可加的尾數可為0~63
//設置當前頁基數
#define		M_LCD_COL_PAGE	0x00b0		//基數指令，后可加尾數0~8
//設置當前列基數
#define		M_LCD_COL_LINE_LOW	0x0004		//基數指令，低四位有效
#define		M_LCD_COL_LINE_HIG	0x0010		//基數指令，低四位有效


#endif