//*****************************************************************************
//   MSP430x42x0 Demo - SD16_A, Using the Integrated Battery Sensor
//
//  Description: This example shows how to use the SD16_A module's integrated
//  Battery sensor (connected to input channel 5) to measure VCC.
//  A single conversion is initiated and then the CPU is disabled by entering
//  LPM0. Once the conversion has completed, a SD16_A interrupt occurs and
//  stores the result in variable "ADCresult".  LED lights if batter is low
//  ACLK = LFXT1 = 32768 Hz, MCLK = SMCLK = DCO = 32 x ACLK = 1048576 Hz
//  //* An external watch crystal on XIN XOUT is required for ACLK     *//	
//  //* Minimum Vcc is required for SD16_A module - see datasheet        *//
//  //* 100nF cap btw Vref and AVss is recommended when using 1.2V ref *//
//
//                MSP430F4270
//             -----------------
//         /|\|              XIN|-
//          | |                 | 32kHz
//          --|RST          XOUT|-
//            |                 |
//            |A5+              | ( A5+, A5- connected internally )
//            |A5-              |
//            |                 |
//            |            VREF |---+
//            |                 |   |
//            |                 |  -+- 100nF
//            |                 |  -+-
//            |                 |   |
//            |            AVss |---+
//            |                 |
//
//  L. Westlund / S. Karthikeyan
//  Texas Instruments Inc.
//  June 2005
//  Built with IAR Embedded Workbench Version: 3.30A
//*****************************************************************************
#include  <msp430x42x0.h>

#define LOW_BAT 0xBFFF                      // ~3V

static unsigned int ADCresult;

void main(void)
{
  volatile unsigned int i;                  // Use volatile to prevent removal
                                            // by compiler optimization
  P1DIR |= 0x01;

  WDTCTL = WDTPW + WDTHOLD;                 // Stop WDT
  FLL_CTL0 |= XCAP14PF;                     // Configure load caps
  for (i = 0; i < 10000; i++);              // Delay for 32 kHz crystal to
                                            // stabilize

  SD16CTL = SD16REFON+SD16SSEL0;            // 1.2V ref, SMCLK
  SD16CCTL0 |= SD16SNGL+SD16IE ;            // Single conv, enable interrupt
  SD16INCTL0 |= SD16INCH_5;                 // Select Channel A5
  for (i = 0; i < 0x3600; i++);             // Delay for 1.2V ref startup

  _EINT();                                  // Enable general interrupts

  while (1)
  {
    SD16CCTL0 |= SD16SC;                    // Set bit to start conversion
    _BIS_SR(LPM0_bits);                     // Enter LPM0
   if( ADCresult < LOW_BAT )
   {
    P1OUT |= 0x01;
   }
   else
   {
     P1OUT &= ~0x01;
   }
    _NOP();                                 //SET BREAKPOINT HERE
  }
}

#pragma vector=SD16_VECTOR
__interrupt void SD16ISR(void)
{
  switch (SD16IV)
  {
  case 2:                                   // SD16MEM Overflow
    break;
  case 4:                                   // SD16MEM0 IFG
    ADCresult = SD16MEM0;                   // Save results (clears IFG)
    break;
  }

  _BIC_SR_IRQ(LPM0_bits);                   // Exit LPM0
}