}
	}
	else
	if (2 == BufferNo)							//read byte(s) from buffer 2
	{
		DF_SPI_RW(Buf2Read);					//buffer 2 read op-code
		DF_SPI_RW(0x00);						//don't cares
		DF_SPI_RW((unsigned char)(IntPageAdr>>8));//upper part of internal buffer address
		DF_SPI_RW((unsigned char)(IntPageAdr));	//lower part of internal buffer address
		DF_SPI_RW(0x00);						//don't cares
		for( i=0; i<No_of_bytes; i++)
		{
			*(BufferPtr) = DF_SPI_RW(0x00);		//read byte and put it in AVR buffer pointed to by *BufferPtr
			BufferPtr++;						//point to next element in AVR buffer
		}
	}
}
//NB : Sjekk at (IntAdr + No_of_bytes) < buffersize, hvis ikke blir det bare ball..



/*****************************************************************************
*
*	Function name : Buffer_Write_Enable
*
*	Returns :		None
*
*	Parameters :	IntPageAdr	->	Internal page address to start writing from
*					BufferAdr	->	Decides usage of either buffer 1 or 2
*					
*	Purpose :		Enables continous write functionality to one of the dataflash buffers
*					buffers. NOTE : User must ensure that CS goes high to terminate
*					this mode before accessing other dataflash functionalities 
*
******************************************************************************/
void Buffer_Write_Enable (unsigned char BufferNo, unsigned int IntPageAdr)
{
	DF_CS_inactive;								//make sure to toggle CS signal in order
	DF_CS_active;								//to reset dataflash command decoder
	
	if (1 == BufferNo)							//write enable to buffer 1
	{
		DF_SPI_RW(Buf1Write);					//buffer 1 write op-code
		DF_SPI_RW(0x00);						//don't cares
		DF_SPI_RW((unsigned char)(IntPageAdr>>8));//upper part of internal buffer address
		DF_SPI_RW((unsigned char)(IntPageAdr));	//lower part of internal buffer address
	}
	else
	if (2 == BufferNo)							//write enable to buffer 2
	{
		DF_SPI_RW(Buf2Write);					//buffer 2 write op-code
		DF_SPI_RW(0x00);						//don't cares
		DF_SPI_RW((unsigned char)(IntPageAdr>>8));//upper part of internal buffer address
		DF_SPI_RW((unsigned char)(IntPageAdr));	//lower part of internal buffer address
	}
}



/*****************************************************************************
*
*	Function name : Buffer_Write_Byte
*
*	Returns :		None
*
*	Parameters :	IntPageAdr	->	Internal page address to write byte to
*					BufferAdr	->	Decides usage of either buffer 1 or 2
*					Data		->	Data byte to be written
*
*	Purpose :		Writes one byte to one of the dataflash
*					internal SRAM buffers
*
******************************************************************************/
void Buffer_Write_Byte (unsigned char BufferNo, unsigned int IntPageAdr, unsigned char Data)
{
	
	DF_CS_inactive;								//make sure to toggle CS signal in order
	DF_CS_active;								//to reset dataflash command decoder
	
	if (1 == BufferNo)							//write byte to buffer 1
	{
		DF_SPI_RW(Buf1Write);					//buffer 1 write op-code
		DF_SPI_RW(0x00);						//don't cares
		DF_SPI_RW((unsigned char)(IntPageAdr>>8));//upper part of internal buffer address
		DF_SPI_RW((unsigned char)(IntPageAdr));	//lower part of internal buffer address
		DF_SPI_RW(Data);						//write data byte
	}
	else
	if (2 == BufferNo)							//write byte to buffer 2
	{
		DF_SPI_RW(Buf2Write);					//buffer 2 write op-code
		DF_SPI_RW(0x00);						//don't cares
		DF_SPI_RW((unsigned char)(IntPageAdr>>8));//upper part of internal buffer address
		DF_SPI_RW((unsigned char)(IntPageAdr));	//lower part of internal buffer address
		DF_SPI_RW(Data);						//write data byte
	}		
}


/*****************************************************************************
*
*	Function name : Buffer_Write_Str
*
*	Returns :		None
*
*	Parameters :	BufferNo	->	Decides usage of either buffer 1 or 2
*					IntPageAdr	->	Internal page address
*					No_of_bytes	->	Number of bytes to be written
*					*BufferPtr	->	address of buffer to be used for copy of bytes
*									from AVR buffer to dataflash buffer 1 (or 2)
*
*	Purpose :		Copies one or more bytes to one of the dataflash
*					internal SRAM buffers from AVR SRAM buffer
*					pointed to by *BufferPtr
*
******************************************************************************/
void Buffer_Write_Str (unsigned char BufferNo, unsigned int IntPageAdr, unsigned int No_of_bytes, unsigned char *BufferPtr)
{
	unsigned int i;

	DF_CS_inactive;								//make sure to toggle CS signal in order
	DF_CS_active;								//to reset dataflash command decoder
	
	if (1 == BufferNo)							//write byte(s) to buffer 1
	{
		DF_SPI_RW(Buf1Write);					//buffer 1 write op-code
		DF_SPI_RW(0x00);						//don't cares
		DF_SPI_RW((unsigned char)(IntPageAdr>>8));//upper part of internal buffer address
		DF_SPI_RW((unsigned char)(IntPageAdr));	//lower part of internal buffer address
		for( i=0; i<No_of_bytes; i++)
		{
			DF_SPI_RW(BufferPtr[i]);			//write byte pointed at by *BufferPtr to dataflash buffer 1 location
			//BufferPtr++;						//point to next element in AVR buffer
		}
	}
	else
	if (2 == BufferNo)							//write byte(s) to buffer 2
	{
		DF_SPI_RW(Buf2Write);					//buffer 2 write op-code
		DF_SPI_RW(0x00);						//don't cares
		DF_SPI_RW((unsigned char)(IntPageAdr>>8));//upper part of internal buffer address
		DF_SPI_RW((unsigned char)(IntPageAdr));	//lower part of internal buffer address
		for( i=0; i<No_of_bytes; i++)
		{
			DF_SPI_RW(*(BufferPtr));			//write byte pointed at by *BufferPtr to dataflash buffer 2 location
			BufferPtr++;						//point to next element in AVR buffer
		}
	}
}
//NB : Monitorer busy-flag i status-reg.
//NB : Sjekk at (IntAdr + No_of_bytes) < buffersize, hvis ikke blir det bare ball..



/*****************************************************************************
*
*	Function name : Buffer_To_Page
*
*	Returns :		None
*
*	Parameters :	BufferAdr	->	Decides usage of either buffer 1 or 2
*					PageAdr		->	Address of flash page to be programmed
*
*	Purpose :		Transfers a page from dataflash SRAM buffer to flash
*					
******************************************************************************/
void Buffer_To_Page (unsigned char BufferNo, unsigned int PageAdr)
{
	DF_CS_inactive;												//make sure to toggle CS signal in order
	DF_CS_active;												//to reset dataflash command decoder
		
	if (1 == BufferNo)											//program flash page from buffer 1
	{
		DF_SPI_RW(Buf1ToFlashWE);								//buffer 1 to flash with erase op-code
		DF_SPI_RW((unsigned char)(PageAdr >> (16 - PageBits)));	//upper part of page address
		DF_SPI_RW((unsigned char)(PageAdr << (PageBits - 8)));	//lower part of page address
		DF_SPI_RW(0x00);										//don't cares
	}
	else	
	if (2 == BufferNo)											//program flash page from buffer 2
	{
		DF_SPI_RW(Buf2ToFlashWE);								//buffer 2 to flash with erase op-code
		DF_SPI_RW((unsigned char)(PageAdr >> (16 - PageBits)));	//upper part of page address
		DF_SPI_RW((unsigned char)(PageAdr << (PageBits - 8)));	//lower part of page address
		DF_SPI_RW(0x00);										//don't cares
	}
	
	DF_CS_inactive;												//initiate flash page programming
	DF_CS_active;												
	
	while(!(Read_DF_status() & 0x80));							//monitor the status register, wait until busy-flag is high
}


/*****************************************************************************
*
*	Function name : Cont_Flash_Read_Enable
*
*	Returns :		None
*
*	Parameters :	PageAdr		->	Address of flash page where cont.read starts from
*					IntPageAdr	->	Internal page address where cont.read starts from
*
*	Purpose :		Initiates a continuous read from a location in the DataFlash
*					
******************************************************************************/
void Cont_Flash_Read_Enable (unsigned int PageAdr, unsigned int IntPageAdr)
{
	DF_CS_inactive;																//make sure to toggle CS signal in order
	DF_CS_active;																//to reset dataflash command decoder
	
	DF_SPI_RW(ContArrayRead);													//Continuous Array Read op-code
	DF_SPI_RW((unsigned char)(PageAdr >> (16 - PageBits)));						//upper part of page address
	DF_SPI_RW((unsigned char)((PageAdr << (PageBits - 8))+ (IntPageAdr>>8)));	//lower part of page address and MSB of int.page adr.
	DF_SPI_RW((unsigned char)(IntPageAdr));										//LSB byte of internal page address
	DF_SPI_RW(0x00);															//perform 4 dummy writes
	DF_SPI_RW(0x00);															//in order to intiate DataFlash
	DF_SPI_RW(0x00);															//address pointers
	DF_SPI_RW(0x00);
}

// *****************************[ End Of DATAFLASH.C ]*************************