//=============================================================================
// File Name : 2440addr.h
// Function  : S3C2440 Define Address Register
// History
//   0.0 : Programming start (February 15,2002) -> SOP
// Revision	: 03.11.2003 ver 0.0	Attatched for 2440
//=============================================================================

#ifndef __2440ADDR_H__
#define __2440ADDR_H__

#ifdef __cplusplus
extern "C" {
#endif

#include "option.h"


// Memory control 
#define rBWSCON    (*(volatile unsigned *)0x48000000)	//Bus width & wait status
#define rBANKCON0  (*(volatile unsigned *)0x48000004)	//Boot ROM control
#define rBANKCON1  (*(volatile unsigned *)0x48000008)	//BANK1 control
#define rBANKCON2  (*(volatile unsigned *)0x4800000c)	//BANK2 cControl
#define rBANKCON3  (*(volatile unsigned *)0x48000010)	//BANK3 control
#define rBANKCON4  (*(volatile unsigned *)0x48000014)	//BANK4 control
#define rBANKCON5  (*(volatile unsigned *)0x48000018)	//BANK5 control
#define rBANKCON6  (*(volatile unsigned *)0x4800001c)	//BANK6 control
#define rBANKCON7  (*(volatile unsigned *)0x48000020)	//BANK7 control
#define rREFRESH   (*(volatile unsigned *)0x48000024)	//DRAM/SDRAM refresh
#define rBANKSIZE  (*(volatile unsigned *)0x48000028)	//Flexible Bank Size
#define rMRSRB6    (*(volatile unsigned *)0x4800002c)	//Mode register set for SDRAM
#define rMRSRB7    (*(volatile unsigned *)0x48000030)	//Mode register set for SDRAM


// USB Host


// INTERRUPT
#define rSRCPND     (*(volatile unsigned *)0x4a000000)	//Interrupt request status
#define rINTMOD     (*(volatile unsigned *)0x4a000004)	//Interrupt mode control
#define rINTMSK     (*(volatile unsigned *)0x4a000008)	//Interrupt mask control
#define rPRIORITY   (*(volatile unsigned *)0x4a00000c)	//IRQ priority control
#define rINTPND     (*(volatile unsigned *)0x4a000010)	//Interrupt request status
#define rINTOFFSET  (*(volatile unsigned *)0x4a000014)	//Interruot request source offset
#define rSUBSRCPND  (*(volatile unsigned *)0x4a000018)	//Sub source pending
#define rINTSUBMSK  (*(volatile unsigned *)0x4a00001c)	//Interrupt sub mask


// DMA
#define rDISRC0     (*(volatile unsigned *)0x4b000000)	//DMA 0 Initial source
#define rDISRCC0    (*(volatile unsigned *)0x4b000004)	//DMA 0 Initial source control
#define rDIDST0     (*(volatile unsigned *)0x4b000008)	//DMA 0 Initial Destination
#define rDIDSTC0    (*(volatile unsigned *)0x4b00000c)	//DMA 0 Initial Destination control
#define rDCON0      (*(volatile unsigned *)0x4b000010)	//DMA 0 Control
#define rDSTAT0     (*(volatile unsigned *)0x4b000014)	//DMA 0 Status
#define rDCSRC0     (*(volatile unsigned *)0x4b000018)	//DMA 0 Current source
#define rDCDST0     (*(volatile unsigned *)0x4b00001c)	//DMA 0 Current destination
#define rDMASKTRIG0 (*(volatile unsigned *)0x4b000020)	//DMA 0 Mask trigger

#define rDISRC1     (*(volatile unsigned *)0x4b000040)	//DMA 1 Initial source
#define rDISRCC1    (*(volatile unsigned *)0x4b000044)	//DMA 1 Initial source control
#define rDIDST1     (*(volatile unsigned *)0x4b000048)	//DMA 1 Initial Destination
#define rDIDSTC1    (*(volatile unsigned *)0x4b00004c)	//DMA 1 Initial Destination control
#define rDCON1      (*(volatile unsigned *)0x4b000050)	//DMA 1 Control
#define rDSTAT1     (*(volatile unsigned *)0x4b000054)	//DMA 1 Status
#define rDCSRC1     (*(volatile unsigned *)0x4b000058)	//DMA 1 Current source
#define rDCDST1     (*(volatile unsigned *)0x4b00005c)	//DMA 1 Current destination
#define rDMASKTRIG1 (*(volatile unsigned *)0x4b000060)	//DMA 1 Mask trigger

#define rDISRC2     (*(volatile unsigned *)0x4b000080)	//DMA 2 Initial source
#define rDISRCC2    (*(volatile unsigned *)0x4b000084)	//DMA 2 Initial source control
#define rDIDST2     (*(volatile unsigned *)0x4b000088)	//DMA 2 Initial Destination
#define rDIDSTC2    (*(volatile unsigned *)0x4b00008c)	//DMA 2 Initial Destination control
#define rDCON2      (*(volatile unsigned *)0x4b000090)	//DMA 2 Control
#define rDSTAT2     (*(volatile unsigned *)0x4b000094)	//DMA 2 Status
#define rDCSRC2     (*(volatile unsigned *)0x4b000098)	//DMA 2 Current source
#define rDCDST2     (*(volatile unsigned *)0x4b00009c)	//DMA 2 Current destination
#define rDMASKTRIG2 (*(volatile unsigned *)0x4b0000a0)	//DMA 2 Mask trigger

#define rDISRC3     (*(volatile unsigned *)0x4b0000c0)	//DMA 3 Initial source
#define rDISRCC3    (*(volatile unsigned *)0x4b0000c4)	//DMA 3 Initial source control
#define rDIDST3     (*(volatile unsigned *)0x4b0000c8)	//DMA 3 Initial Destination
#define rDIDSTC3    (*(volatile unsigned *)0x4b0000cc)	//DMA 3 Initial Destination control
#define rDCON3      (*(volatile unsigned *)0x4b0000d0)	//DMA 3 Control
#define rDSTAT3     (*(volatile unsigned *)0x4b0000d4)	//DMA 3 Status
#define rDCSRC3     (*(volatile unsigned *)0x4b0000d8)	//DMA 3 Current source
#define rDCDST3     (*(volatile unsigned *)0x4b0000dc)	//DMA 3 Current destination
#define rDMASKTRIG3 (*(volatile unsigned *)0x4b0000e0)	//DMA 3 Mask trigger


// CLOCK & POWER MANAGEMENT
#define rLOCKTIME   (*(volatile unsigned *)0x4c000000)	//PLL lock time counter
#define rMPLLCON    (*(volatile unsigned *)0x4c000004)	//MPLL Control
#define rUPLLCON    (*(volatile unsigned *)0x4c000008)	//UPLL Control
#define rCLKCON     (*(volatile unsigned *)0x4c00000c)	//Clock generator control
#define rCLKSLOW    (*(volatile unsigned *)0x4c000010)	//Slow clock control
#define rCLKDIVN    (*(volatile unsigned *)0x4c000014)	//Clock divider control
#define rCAMDIVN    (*(volatile unsigned *)0x4c000018)	//USB, CAM Clock divider control


// LCD CONTROLLER
#define rLCDCON1    (*(volatile unsigned *)0x4d000000)	//LCD control 1
#define rLCDCON2    (*(volatile unsigned *)0x4d000004)	//LCD control 2
#define rLCDCON3    (*(volatile unsigned *)0x4d000008)	//LCD control 3
#define rLCDCON4    (*(volatile unsigned *)0x4d00000c)	//LCD control 4
#define rLCDCON5    (*(volatile unsigned *)0x4d000010)	//LCD control 5
#define rLCDSADDR1  (*(volatile unsigned *)0x4d000014)	//STN/TFT Frame buffer start address 1
#define rLCDSADDR2  (*(volatile unsigned *)0x4d000018)	//STN/TFT Frame buffer start address 2
#define rLCDSADDR3  (*(volatile unsigned *)0x4d00001c)	//STN/TFT Virtual screen address set
#define rREDLUT     (*(volatile unsigned *)0x4d000020)	//STN Red lookup table
#define rGREENLUT   (*(volatile unsigned *)0x4d000024)	//STN Green lookup table 
#define rBLUELUT    (*(volatile unsigned *)0x4d000028)	//STN Blue lookup table
#define rDITHMODE   (*(volatile unsigned *)0x4d00004c)	//STN Dithering mode
#define rTPAL       (*(volatile unsigned *)0x4d000050)	//TFT Temporary palette
#define rLCDINTPND  (*(volatile unsigned *)0x4d000054)	//LCD Interrupt pending
#define rLCDSRCPND  (*(volatile unsigned *)0x4d000058)	//LCD Interrupt source
#define rLCDINTMSK  (*(volatile unsigned *)0x4d00005c)	//LCD Interrupt mask
#define rTCONSEL     (*(volatile unsigned *)0x4d000060)	//LPC3600 Control --- edited by junon
#define PALETTE     0x4d000400						//Palette start address


//Nand Flash
#define rNFCONF		(*(volatile unsigned *)0x4E000000)		//NAND Flash configuration
#define rNFCONT		(*(volatile unsigned *)0x4E000004)      //NAND Flash control
#define rNFCMD		(*(volatile unsigned *)0x4E000008)      //NAND Flash command
#define rNFADDR		(*(volatile unsigned *)0x4E00000C)      //NAND Flash address
#define rNFDATA		(*(volatile unsigned *)0x4E000010)      //NAND Flash data
#define rNFDATA8	(*(volatile unsigned char *)0x4E000010)     //NAND Flash data
#define NFDATA		(0x4E000010)      //NAND Flash data address
#define rNFMECCD0	(*(volatile unsigned *)0x4E000014)      //NAND Flash ECC for Main Area
#define rNFMECCD1	(*(volatile unsigned *)0x4E000018)
#define rNFSECCD	(*(volatile unsigned *)0x4E00001C)		//NAND Flash ECC for Spare Area
#define rNFSTAT		(*(volatile unsigned *)0x4E000020)		//NAND Flash operation status
#define rNFESTAT0	(*(volatile unsigned *)0x4E000024)
#define rNFESTAT1	(*(volatile unsigned *)0x4E000028)
#define rNFMECC0	(*(volatile unsigned *)0x4E00002C)
#define rNFMECC1	(*(volatile unsigned *)0x4E000030)
#define rNFSECC		(*(volatile unsigned *)0x4E000034)
#define rNFSBLK		(*(volatile unsigned *)0x4E000038)		//NAND Flash Start block address
#define rNFEBLK		(*(volatile unsigned *)0x4E00003C)		//NAND Flash End block address


//Camera Interface.  Edited for 2440A                              
#define rCISRCFMT           (*(volatile unsigned *)0x4F000000)        
#define rCIWDOFST           (*(volatile unsigned *)0x4F000004)        
#define rCIGCTRL            (*(volatile unsigned *)0x4F000008)        
#define rCICOYSA1           (*(volatile unsigned *)0x4F000018)
#define rCICOYSA2           (*(volatile unsigned *)0x4F00001C)
#define rCICOYSA3           (*(volatile unsigned *)0x4F000020)        
#define rCICOYSA4           (*(volatile unsigned *)0x4F000024)        
#define rCICOCBSA1          (*(volatile unsigned *)0x4F000028)        
#define rCICOCBSA2          (*(volatile unsigned *)0x4F00002C)        
#define rCICOCBSA3          (*(volatile unsigned *)0x4F000030)        
#define rCICOCBSA4          (*(volatile unsigned *)0x4F000034)
#define rCICOCRSA1          (*(volatile unsigned *)0x4F000038)
#define rCICOCRSA2          (*(volatile unsigned *)0x4F00003C)
#define rCICOCRSA3          (*(volatile unsigned *)0x4F000040)
#define rCICOCRSA4          (*(volatile unsigned *)0x4F000044)
#define rCICOTRGFMT         (*(volatile unsigned *)0x4F000048)
#define rCICOCTRL           (*(volatile unsigned *)0x4F00004C)        
#define rCICOSCPRERATIO     (*(volatile unsigned *)0x4F000050)        
#define rCICOSCPREDST       (*(volatile unsigned *)0x4F000054)
#define rCICOSCCTRL         (*(volatile unsigned *)0x4F000058)
#define rCICOTAREA          (*(volatile unsigned *)0x4F00005C)
#define rCICOSTATUS         (*(volatile unsigned *)0x4F000064)
#define rCIPRCLRSA1         (*(volatile unsigned *)0x4F00006C)
#define rCIPRCLRSA2         (*(volatile unsigned *)0x4F000070)
#define rCIPRCLRSA3         (*(volatile unsigned *)0x4F000074)        
#define rCIPRCLRSA4         (*(volatile unsigned *)0x4F000078)        
#define rCIPRTRGFMT         (*(volatile unsigned *)0x4F00007C)        
#define rCIPRCTRL           (*(volatile unsigned *)0x4F000080)        
#define rCIPRSCPRERATIO     (*(volatile unsigned *)0x4F000084)        
#define rCIPRSCPREDST       (*(volatile unsigned *)0x4F000088)        
#define rCIPRSCCTRL         (*(volatile unsigned *)0x4F00008C)        
#define rCIPRTAREA          (*(volatile unsigned *)0x4F000090)
#define rCIPRSTATUS         (*(volatile unsigned *)0x4F000098)
#define rCIIMGCPT           (*(volatile unsigned *)0x4F0000A0)


// UART
#define rULCON0     (*(volatile unsigned *)0x50000000)	//UART 0 Line control
#define rUCON0      (*(volatile unsigned *)0x50000004)	//UART 0 Control
#define rUFCON0     (*(volatile unsigned *)0x50000008)	//UART 0 FIFO control
#define rUMCON0     (*(volatile unsigned *)0x5000000c)	//UART 0 Modem control
#define rUTRSTAT0   (*(volatile unsigned *)0x50000010)	//UART 0 Tx/Rx status
#define rUERSTAT0   (*(volatile unsigned *)0x50000014)	//UART 0 Rx error status
#define rUFSTAT0    (*(volatile unsigned *)0x50000018)	//UART 0 FIFO status
#define rUMSTAT0    (*(volatile unsigned *)0x5000001c)	//UART 0 Modem status
#define rUBRDIV0    (*(volatile unsigned *)0x50000028)	//UART 0 Baud rate divisor

#define rULCON1     (*(volatile unsigned *)0x50004000)	//UART 1 Line control
#define rUCON1      (*(volatile unsigned *)0x50004004)	//UART 1 Control
#define rUFCON1     (*(volatile unsigned *)0x50004008)	//UART 1 FIFO control
#define rUMCON1     (*(volatile unsigned *)0x5000400c)	//UART 1 Modem control
#define rUTRSTAT1   (*(volatile unsigned *)0x50004010)	//UART 1 Tx/Rx status
#define rUERSTAT1   (*(volatile unsigned *)0x50004014)	//UART 1 Rx error status
#define rUFSTAT1    (*(volatile unsigned *)0x50004018)	//UART 1 FIFO status
#define rUMSTAT1    (*(volatile unsigned *)0x5000401c)	//UART 1 Modem status
#define rUBRDIV1    (*(volatile unsigned *)0x50004028)	//UART 1 Baud rate divisor
#define rULCON2     (*(volatile unsigned *)0x50008000)	//UART 2 Line control
#define rUCON2      (*(volatile unsigned *)0x50008004)	//UART 2 Control
#define rUFCON2     (*(volatile unsigned *)0x50008008)	//UART 2 FIFO control
#define rUMCON2     (*(volatile unsigned *)0x5000800c)	//UART 2 Modem control
#define rUTRSTAT2   (*(volatile unsigned *)0x50008010)	//UART 2 Tx/Rx status
#define rUERSTAT2   (*(volatile unsigned *)0x50008014)	//UART 2 Rx error status
#define rUFSTAT2    (*(volatile unsigned *)0x50008018)	//UART 2 FIFO status
#define rUMSTAT2    (*(volatile unsigned *)0x5000801c)	//UART 2 Modem status
#define rUBRDIV2    (*(volatile unsigned *)0x50008028)	//UART 2 Baud rate divisor

#ifdef __BIG_ENDIAN
#define rUTXH0      (*(volatile unsigned char *)0x50000023)	//UART 0 Transmission Hold
#define rURXH0      (*(volatile unsigned char *)0x50000027)	//UART 0 Receive buffer
#define rUTXH1      (*(volatile unsigned char *)0x50004023)	//UART 1 Transmission Hold
#define rURXH1      (*(volatile unsigned char *)0x50004027)	//UART 1 Receive buffer
#define rUTXH2      (*(volatile unsigned char *)0x50008023)	//UART 2 Transmission Hold
#define rURXH2      (*(volatile unsigned char *)0x50008027)	//UART 2 Receive buffer

#define WrUTXH0(ch) (*(volatile unsigned char *)0x50000023)=(unsigned char)(ch)
#define RdURXH0()   (*(volatile unsigned char *)0x50000027)
#define WrUTXH1(ch) (*(volatile unsigned char *)0x50004023)=(unsigned char)(ch)
#define RdURXH1()   (*(volatile unsigned char *)0x50004027)
#define WrUTXH2(ch) (*(volatile unsigned char *)0x50008023)=(unsigned char)(ch)
#define RdURXH2()   (*(volatile unsigned char *)0x50008027)

#define UTXH0       (0x50000020+3)  //Byte_access address by DMA
#define URXH0       (0x50000024+3)
#define UTXH1       (0x50004020+3)
#define URXH1       (0x50004024+3)
#define UTXH2       (0x50008020+3)
#define URXH2       (0x50008024+3)

#else //Little Endian
#define rUTXH0 (*(volatile unsigned char *)0x50000020)	//UART 0 Transmission Hold
#define rURXH0 (*(volatile unsigned char *)0x50000024)	//UART 0 Receive buffer
#define rUTXH1 (*(volatile unsigned char *)0x50004020)	//UART 1 Transmission Hold
#define rURXH1 (*(volatile unsigned char *)0x50004024)	//UART 1 Receive buffer
#define rUTXH2 (*(volatile unsigned char *)0x50008020)	//UART 2 Transmission Hold
#define rURXH2 (*(volatile unsigned char *)0x50008024)	//UART 2 Receive buffer