$Id: input-programming.txt,v 1.4 2001/05/04 09:47:14 vojtech Exp $Programming input drivers~~~~~~~~~~~~~~~~~~~~~~~~~1. Creating an input device driver~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~1.0 The simplest example~~~~~~~~~~~~~~~~~~~~~~~~Here comes a very simple example of an input device driver. The device hasjust one button and the button is accessible at i/o port BUTTON_PORT. Whenpressed or released a BUTTON_IRQ happens. The driver could look like:#include <linux/input.h>#include <linux/module.h>#include <linux/init.h>#include <asm/irq.h>#include <asm/io.h>static void button_interrupt(int irq, void *dummy, struct pt_regs *fp){	input_report_key(&button_dev, BTN_1, inb(BUTTON_PORT) & 1);}static int __init button_init(void){	if (request_irq(BUTTON_IRQ, button_interrupt, 0, "button", NULL)) {                printk(KERN_ERR "button.c: Can't allocate irq %d\n", button_irq);                return -EBUSY;        }		button_dev.evbit[0] = BIT(EV_KEY);	button_dev.keybit[LONG(BTN_0)] = BIT(BTN_0);		input_register_device(&button_dev);}static void __exit button_exit(void){        input_unregister_device(&button_dev);	free_irq(BUTTON_IRQ, button_interrupt);}module_init(button_init);module_exit(button_exit);1.1 What the example does~~~~~~~~~~~~~~~~~~~~~~~~~First it has to include the <linux/input.h> file, which interfaces to theinput subsystem. This provides all the definitions needed.In the _init function, which is called either upon module load or whenbooting the kernel, it grabs the required resources (it should also checkfor the presence of the device).Then it sets the input bitfields. This way the device driver tells the otherparts of the input systems what it is - what events can be generated oraccepted by this input device. Our example device can only generate EV_KEY typeevents, and from those only BTN_0 event code. Thus we only set these twobits. We could have used	set_bit(EV_KEY, button_dev.evbit);	set_bit(BTN_0, button_dev.keybit);as well, but with more than single bits the first approach tends to beshorter. Then the example driver registers the input device structure by calling	input_register_device(&button_dev);This adds the button_dev structure to linked lists of the input driver andcalls device handler modules _connect functions to tell them a new inputdevice has appeared. Because the _connect functions may call kmalloc(,GFP_KERNEL), which can sleep, input_register_device() must not be calledfrom an interrupt or with a spinlock held.While in use, the only used function of the driver is	button_interrupt()which upon every interrupt from the button checks its state and reports itvia the 	input_report_btn()call to the input system. There is no need to check whether the interruptroutine isn't reporting two same value events (press, press for example) tothe input system, because the input_report_* functions check thatthemselves.1.2 dev->open() and dev->close()~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~In case the driver has to repeatedly poll the device, because it doesn'thave an interrupt coming from it and the polling is too expensive to be doneall the time, or if the device uses a valuable resource (eg. interrupt), itcan use the open and close callback to know when it can stop polling orrelease the interrupt and when it must resume polling or grab the interruptagain. To do that, we would add this to our example driver:int button_used = 0;static int button_open(struct input_dev *dev){        if (button_used++)                return 0;	if (request_irq(BUTTON_IRQ, button_interrupt, 0, "button", NULL)) {                printk(KERN_ERR "button.c: Can't allocate irq %d\n", button_irq);                button_used--;                return -EBUSY;        }        return 0;}static void button_close(struct input_dev *dev){        if (!--button_used)                free_irq(IRQ_AMIGA_VERTB, button_interrupt);}static int __init button_init(void){	...	button_dev.open = button_open;	button_dev.close = button_close;	...}Note the button_used variable - we have to track how many times the openfunction was called to know when exactly our device stops being used.The open() callback should return a 0 in case of succes or any nonzero valuein case of failure. The close() callback (which is void) must always succeed.1.3 Basic event types~~~~~~~~~~~~~~~~~~~~~The most simple event type is EV_KEY, which is used for keys and buttons.It's reported to the input system via:	input_report_key(struct input_dev *dev, int code, int value)See linux/input.h for the allowable values of code (from 0 to KEY_MAX).Value is interpreted as a truth value, ie any nonzero value means keypressed, zero value means key released. The input code generates events onlyin case the value is different from before.In addition to EV_KEY, there are two more basic event types: EV_REL andEV_ABS. They are used for relative and absolute values supplied by thedevice. A relative value may be for example a mouse movement in the X axis.The mouse reports it as a relative difference from the last position,because it doesn't have any absolute coordinate system to work in. Absoluteevents are namely for joysticks and digitizers - devices that do work in anabsolute coordinate systems.Having the device report EV_REL buttons is as simple as with EV_KEY, simplyset the corresponding bits and call the	input_report_rel(struct input_dev *dev, int code, int value)function. Events are generated only for nonzero value. However EV_ABS requires a little special care. Before callinginput_register_devices, you have to fill additional fields in the input_devstruct for each absolute axis your device has. If our button device had alsothe ABS_X axis:	button_dev.absmin[ABS_X] = 0;	button_dev.absmax[ABS_X] = 255;	button_dev.absfuzz[ABS_X] = 4;	button_dev.absflat[ABS_X] = 8;This setting would be appropriate for a joystick X axis, with the minimum of0, maximum of 255 (which the joystick *must* be able to reach, no problem ifit sometimes reports more, but it must be able to always reach the min andmax values), with noise in the data up to +- 4, and with a center flatposition of size 8.If you don't need absfuzz and absflat, you can set them to zero, which meanthat the thing is precise and always returns to exactly the center position(if it has any).1.4 The void *private field~~~~~~~~~~~~~~~~~~~~~~~~~~~This field in the input structure can be used to point to any private datastructures in the input device driver, in case the driver handles more thanone device. You'll need it in the open and close callbacks.1.5 NBITS(), LONG(), BIT()~~~~~~~~~~~~~~~~~~~~~~~~~~These three macros frin input.h help some bitfield computations:	NBITS(x) - returns the length of a bitfield array in longs for x bits	LONG(x)  - returns the index in the array in longs for bit x	BIT(x)   - returns the indes in a long for bit x1.6 The number, id* and name fields~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~The dev->number is assigned by the input system to the input device when itis registered. It has no use except for identifying the device to the userin system messages.The dev->name should be set before registering the input device by the inputdevice driver. It's a string like 'Generic button device' containing anuser friendly name of the device.The id* fields contain the bus ID (PCI, USB, ...), vendor ID and device IDof the device. The bus IDs are defined in input.h. The vendor and device idsare defined in pci_ids.h, usb_ids.h and similar include files. These fieldsshould be set by the input device driver before registering it.The idtype field can be used for specific information for the input devicedriver.The id and name fields can be passed to userland via the evdev interface.1.7 The keycode, keycodemax, keycodesize fields~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~These two fields will be used for any inpur devices that report their dataas scancodes. If not all scancodes can be known by autodetection, they mayneed to be set by userland utilities. The keycode array then is an arrayused to map from scancodes to input system keycodes. The keycode max willcontain the size of the array and keycodesize the size of each entry in it(in bytes).1.8 Key autorepeat~~~~~~~~~~~~~~~~~~... is simple. It is handled by the input.c module. Hardware autorepeat isnot used, because it's not present in many devices and even where it ispresent, it is broken sometimes (at keyboards: Toshiba notebooks). To enableautorepeat for your device, just set EV_REP in dev->evbit. All will behandled by the input system.1.9 Other event types, handling output events~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~The other event types up to now are:EV_LED - used for the keyboad LEDs.EV_SND - used for keyboard beeps.They are very similar to for example key events, but they go in the otherdirection - from the system to the input device driver. If your input devicedriver can handle these events, it has to set the respective bits in evbit,*and* also the callback routine:	button_dev.event = button_event;int button_event(struct input_dev *dev, unsigned int type, unsigned int code, int value);{	if (type == EV_SND && code == EV_BELL) {		outb(value, BUTTON_BELL);		return 0;	}	return -1;}This callback routine can be called from an interrupt or a BH (although thatisn't a rule), and thus must not sleep, and must not take too long to finish.