#define MAIN_C
#include "includes.h"
/***************************/
/*PWM*/
/*晶振為4MHz*/
/*利用Timer1的OC1A腳輸出占空比可調的信號*/
/*通過按鍵控制OCR1A的值*/
/***************************/

#define PwmOut     PB1     //A通道的PWM輸出
#define OCR        OCR1A
#define KeyUp      PC0     //增大PWM值的按鍵
#define KeyDown    PC1     //減小PWM值的按鍵
#define Above      PC2     //設置位值過高指示
#define Below      PC3     //設置位值過低指示
#define STEP       64      //定義按鍵時的步進值
int OcrReg = 1024;         //OCR1A初始值
int Icr1Reg = 0x7ff;       //PWM的計數頂部值  Icr1Reg = 2047
//unsigned char *show = "0000"; 
unsigned char temp;

void init(void)   //初始化函數
{
    //比較匹配時清零，計數到最大時置位OC1A
    TCCR1A |= (1<<COM1A1)|(1<<WGM11);  
    //11位分辨率，快速PWM模式，使用系統時鐘作為計數時鐘
    TCCR1B |= (1<<WGM13)|(1<<WGM12)|(1<<CS10);
    ICR1   = Icr1Reg;  
    OCR    = 0 ;
    DDRB  |= (1<<PwmOut);          //置PWM為輸出
    DDRC  |= (1<<Above)|(1<<Below);      //指示燈定義為輸出
    DDRC  &= ~((1<<KeyUp)|(1<<KeyDown)); //按鍵定義為輸入
    PORTC |= (1<<KeyUp)|(1<<KeyDown);    //按鍵開啟上拉
    PORTC |= (1<<Above)|(1<<Below);      //關閉兩個指示燈
    //TIMSK |= (1<<OCIE1A);   //允許計數器比較匹配中斷
    //SREG  |= (1<<7);   //開全局中斷
}

void  ShowValue(int value)
{
    unsigned char *temp = "0000";
    temp[0] = value/1000 + 0x30;
    value = value%1000;
    temp[1] = value/100 +0x30;
    value = value%100;
    temp[2] = value/10 + 0x30;
    value = value%10;
    temp[3] = value + 0x30;  
    ClearLine(2);
    LCD_DisplayString(2,1,"OCR1A = ");
    LCD_DisplayString(2,9,temp);  
}
 
void main(void)
{ 
    unsigned char i; 
    init();
    Init_LCD();
    OCR = OcrReg;
    LCD_DisplayString(1,1,"PWM test");
    LCD_DisplayString(2,1,"OCR1A = ");
    ShowValue(OcrReg);
    while(1)
    {                
        if(!(PINC&(1<<KeyUp)))
        {
            delay_nms(10);    //按鍵消抖
            if(!(PINC&(1<<KeyUp)))
            {
                while(!(PINC&(1<<KeyUp)));  //等待按鍵釋放
                if(OcrReg >= (Icr1Reg+1))
                {
                    for(i=0;i<5;i++)
                    {
                        PORTC ^= (1<<Above);
                        delay_nms(200);
                    }
                    ClearLine(2);
                    LCD_DisplayString(2,1,"Value MAX!");
                }
                else
                {
                    PORTC |= (1<<Above);
                    OcrReg += STEP;                    
                    OCR = OcrReg;
                    ShowValue(OcrReg);
                }
            }
        }
        if(!(PINC&(1<<KeyDown)))
        {
            delay_nms(10);    //按鍵消抖
            if(!(PINC&(1<<KeyDown)))
            {
                while(!(PINC&(1<<KeyDown)));  //等待按鍵釋放
                if(OcrReg <= 0)
                {
                    for(i=0;i<5;i++)
                    {
                        PORTC ^= (1<<Below);
                        delay_nms(200);
                    }
                     ClearLine(2);
                    LCD_DisplayString(2,1,"Value MIN!");
                }
                else
                {
                    PORTC |= (1<<Below);
                    OcrReg -= STEP;
                    OCR = OcrReg;
                    ShowValue(OcrReg);
                }
            }
        }       
    }
}