/********************************************************************* * * Copyright: *	Advanced Micro Devices, AMD. All Rights Reserved.   *  You are hereby granted a copyright license to use, modify, and *  distribute the SOFTWARE so long as this entire notice is *  retained without alteration in any modified and/or redistributed *  versions, and that such modified versions are clearly identified *  as such. No licenses are granted by implication, estoppel or *  otherwise under any patents or trademarks of AMD. This  *  software is provided on an "AS IS" basis and without warranty. * *  To the maximum extent permitted by applicable law, AMD  *  DISCLAIMS ALL WARRANTIES WHETHER EXPRESS OR IMPLIED, INCLUDING  *  IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR *  PURPOSE AND ANY WARRANTY AGAINST INFRINGEMENT WITH REGARD TO THE  *  SOFTWARE (INCLUDING ANY MODIFIED VERSIONS THEREOF) AND ANY  *  ACCOMPANYING WRITTEN MATERIALS. *  *  To the maximum extent permitted by applicable law, IN NO EVENT *  SHALL AMD BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING  *  WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS  *  INTERRUPTION, LOSS OF BUSINESS INFORMATION, OR OTHER PECUNIARY *  LOSS) ARISING OF THE USE OR INABILITY TO USE THE SOFTWARE.    *  *  AMD assumes no responsibility for the maintenance and support *  of this software. ********************************************************************//*This file represents all the activities necessary to bringthe Au1200 out of reset. It sets all Au1200 resources toknown, usually disabled and safe, state.This is an example startup file, tailored for the DBAu1200reference board. DBAu1200-specific items are commented assuch, but in general are confined to the CPU endianselection and memory controller values.*//********************************************************************//* * MIPS ABI register defintions */#define zero		$0#define v0		$2#define v1		$3#define a0		$4#define a1		$5#define a2		$6#define a3		$7#define t0		$8#define t1		$9#define t2		$10#define t3		$11#define t4		$12#define t5		$13#define t6		$14#define t7		$15#define s0		$16#define s1		$17#define s2		$18#define s3		$19#define s4		$20#define s5		$21#define s6		$22#define s7		$23#define t8		$24#define t9		$25#define k0		$26#define k1		$27#define gp		$28#define sp		$29#define fp		$30#define ra		$31/********************************************************************//* * Au1200 CP0 registers */#define CP0_Index		$0#define CP0_Random		$1#define CP0_EntryLo0	$2#define CP0_EntryLo1	$3#define CP0_Context		$4#define CP0_PageMask	$5#define CP0_Wired		$6#define CP0_BadVAddr	$8#define CP0_Count		$9#define CP0_EntryHi		$10#define CP0_Compare		$11#define CP0_Status		$12#define CP0_Cause		$13#define CP0_EPC		$14#define CP0_PRId		$15#define CP0_Config		$16#define CP0_Config0		$16#define CP0_Config1		$16,1#define CP0_LLAddr		$17#define CP0_WatchLo		$18#define CP0_IWatchLo	$18,1#define CP0_WatchHi		$19#define CP0_IWatchHi	$19,1#define CP0_Scratch		$22#define CP0_Debug		$23#define CP0_DEPC		$24#define CP0_PerfCnt		$25#define CP0_PerfCtrl	$25,1#define CP0_DTag		$28#define CP0_DData		$28,1#define CP0_ITag		$29#define CP0_IData		$29,1#define CP0_ErrorEPC	$30#define CP0_DESave		$31/********************************************************************//* * Au1200 base addresses (in KSEG1 region) */#define AU1200_MEM_ADDR		0xB4000000#define AU1200_MAEBE_ADDR		0xB4010000#define AU1200_MAEFE_ADDR		0xB4012000#define AU1200_DDMA_ADDR		0xB4003000#define AU1200_USB_ADDR		0xB4020000#define AU1200_OTG_ADDR		0xB4020020#define AU1200_OHC_ADDR		0xB4020100#define AU1200_EHC_ADDR		0xB4020200#define AU1200_DEV_ADDR		0xB4022000#define AU1200_CIM_ADDR		0xB4004000#define AU1200_LCD_ADDR		0xB5000000#define AU1200_IC0_ADDR		0xB0400000#define AU1200_UART0_ADDR		0xB1100000#define AU1200_UART1_ADDR		0xB1200000#define AU1200_SWC_ADDR		0xB1100100#define AU1200_GPIO2_ADDR		0xB1700000#define AU1200_IC1_ADDR		0xB1800000#define AU1200_SYS_ADDR		0xB1900000#define AU1200_PSC0_ADDR		0xB1A00000#define AU1200_PSC1_ADDR		0xB1B00000#define AU1200_AES_ADDR		0xB0300000#define AU1200_SD0_ADDR		0xB0600000#define AU1200_SD1_ADDR		0xB0680000/* * Au1200 memory controller register offsets */#define mem_sdmode0	    		0x0800#define mem_sdmode1	    		0x0808#define mem_sdaddr0    		0x0820#define mem_sdaddr1    		0x0828#define mem_sdconfiga		0x0840#define mem_sdconfigb		0x0848#define mem_sdstat			0x0850#define mem_sdwrmd0 		0x0880#define mem_sdwrmd1 		0x0888#define mem_sdprecmd		0x08C0#define mem_sdautoref		0x08C8#define mem_sdsref			0x08D0#define mem_stcfg0			0x1000#define mem_sttime0			0x1004#define mem_staddr0			0x1008#define mem_stcfg1			0x1010#define mem_sttime1			0x1014#define mem_staddr1			0x1018#define mem_stcfg2			0x1020#define mem_sttime2			0x1024#define mem_staddr2			0x1028#define mem_stcfg3			0x1030#define mem_sttime3			0x1034#define mem_staddr3			0x1038#define mem_staltime		0x1040#define mem_stndctrl		0x1100/* * Au1200 peripheral register offsets */#define ddma_inten			0x000C#define psc_enable			0x0004		#define uart_enable			0x0100#define maebe_ctlenable		0x0700#define cim_enable			0x0000#define lcd_screen			0x0004#define swcnt_control		0x0000#define usb_cfg			0x0004#define sd_enable			0x000C#define aes_status			0x0000#define ic_cfg0clr			0x0044#define ic_cfg1clr			0x004C#define ic_cfg2clr			0x0054#define ic_srcset			0x0058#define ic_assignset		0x0060#define ic_wakeclr			0x006C#define ic_maskclr			0x0074#define ic_risingclr		0x0078#define ic_fallingclr		0x007C#define ic_testbit			0x0080#define sys_scratch0		0x0018#define sys_scratch1		0x001c#define sys_cntctrl			0x0014#define sys_freqctrl0		0x0020#define sys_freqctrl1		0x0024#define sys_clksrc			0x0028#define sys_pinfunc			0x002C#define sys_wakemsk			0x0034#define sys_powerctrl		0x003C#define sys_endian			0x0038#define sys_wakesrc			0x005C#define sys_cpupll			0x0060#define sys_auxpll			0x0064#define sys_trioutclr		0x0100#define sys_outputset		0x0108#define sys_outputclr		0x010C#define sys_pininputen		0x0110#define gpio2_dir			0x0000#define gpio2_output		0x0008#define gpio2_pinstate		0x000C#define gpio2_inten			0x0010#define gpio2_enable		0x0014/********************************************************************//* * DBAu1200-specific values * NOTE: All values are for operation at 396MHz, SD=2 *///#define SYS_CPUPLL		28	/* 336Mhz */#define SYS_CPUPLL		33	/* 396Mhz */#define SYS_POWERCTRL	0	/* SD=2 */#define SYS_AUXPLL		0	/* disable *//* * With SBUS of 198MHz and mem_stcfg0[TS]=0, static bus controller * clock period is 5ns *//* Address Latch Timing - SN74LVC16374ADVG latch on rising edge of ALE  Tah=000 (0   clocks)  Tlw=000 (1+0 clocks) Tasu=001 (1   clocks) Latch needs 3ns */#define MEM_STALTIME 0x00000001/* RCE0: 120ns x16 Nor Flash Tcsoe= (1+0  clocks) data sheet specs MAX(tCE 120ns - tOE 25ns), choose 5ns for stable address, AS=1 Toecs= (0+0  clocks) data sheet specs   0ns, AH=0  Twcs= (1+0  clocks) data sheet specs   0ns for tCH  Tcsh= (1+6  clocks) data sheet specs MAX(tWPH 30ns, tCEH 35ns)Tcsoff= (1+6  clocks) match Tcsh   Twp= (1+6  clocks) data sheet specs  35ns for tWP  Tcsw= (1+0  clocks) data sheet specs   0ns for tCS   Tpm= (1+7  clocks) data sheet specs  40ns for tPACC    Ta= (1+23 clocks) data sheet specs 120ns for tRCmem_stcfg0: 0000 0000 0010 1101 0000 0000 0100 0011 : 0x002D0043Tcsoe=000 (see above)Toecs=000 (see above)   AH=0   (not needed)   NW=0   (n/a)   AS=1   (setup needed)    S=0   (asynchronous)   DE=1   (de-assert) MBSa=1  MBC=0   TA=1   (Tcsh for reads and writes)  DIV=000 (n/a)  ALD=0   (address latch enable)   AV=0   (no address visibility)   BE=0   (little endian)   TS=0   (asynchronous operation)   EW=0   (n/a) MBSb=1   BS=0   (n/a)   PM=0   (disable page mode)   RO=0   (writable)  DTY=3   (NOR Flash)mem_sttime0: 0000 0110 0110 0001 1000 0001 1001 0101 : 0x06618195  Twcs=000  Tcsh=0110Tcsoff=110   Twp=000110  Tcsw=0000   Tpm=0111    Ta=010111 */#define MEM_STCFG0		0x002D0043 /* 16-bit little-endian */#define MEM_STTIME0		0x066181D7#define MEM_STADDR0		0x11C03F00 /* 64MB address space *//* RCE1: x8 NAND Flash */#define MEM_STCFG1		0x00420045#define MEM_STTIME1		0x00007774#define MEM_STADDR1		0x12003FFF/* RCE2: IDE PIOmode4 Tcsoe=MAX( 0ns,      20ns,         25ns) = (1+4  clocks) AS=1 Toecs=MAX( 0ns,       5ns,         10ns) = (1+1  clocks) AH=1  Twcs=MAX( 0ns,       5ns,         10ns) = (1+1  clocks)  Tcsh=MAX(10ns,      20ns,         25ns) = (1+4  clocks)Tcsoff=MAX(10ns,      20ns,         25ns) = (1+4  clocks)   Twp=MAX(15ns,      20ns,         70ns) = (1+13 clocks)  Tcsw=MAX(10ns,      20ns,         20ns) = (1+3  clocks)   Tpm=MAX( 0ns,       0ns,       25/0ns) = (1+0  clocks)    Ta=MAX( 5ns,      35ns,         95ns) = (1+18 clocks)mem_stcfg2: 1000 0110 0010 1101 0000 0000 1100 0110 : 0x862D00C6 Tcsoe=100 (see above)Toecs=001 (see above)   AH=1   (hold needed)   NW=0   (n/a)   AS=1   (setup needed)    S=0   (asynchronous)   DE=1   (de-assert) MBSa=1  MBC=0   TA=1   (Tcsh for reads and writes)   BE=0   (little endian)   TS=0   (asynchronous operation)   EW=1   (absolutely needed) MBSb=1   BS=0   (n/a)   PM=0   (disable page mode)   RO=0   (writable)  DTY=6   (IDE)mem_sttime2: 0001 0100 0100 0011 0100 1100 0001 0010 : 0x14434C12  Twcs=001  Tcsh=0100Tcsoff=100   Twp=001101  Tcsw=0011   Tpm=0000    Ta=010010*/#define MEM_STCFG2		0x862D00C6#define MEM_STTIME2		0x14434C12#define MEM_STADDR2		0x11803f00/* RCE3: PCMCIA 250ns */#define MEM_STCFG3		0x00040042#define MEM_STTIME3		0x280E3E07#define MEM_STADDR3		0x10000000#define MEM_SDCONFIGA_E	(1<<31)#define MEM_SDCONFIGA_CE	(3<<28)#define MEM_SDCONFIGB_BB	(1<<19)#define MEM_SDCONFIGB_BA	(1<<7)#define MEM_SDCONFIGB_PM  (2<<22)/* * SDCS0: 1:32MB gDDR2 Hynix HY5Ps561621AFP x 2 or          2:64MB gDDR2 Hynix HY5PS121621BFP x 1   SDCS1: NoneWith a DDR clock of 198MHz (sdconfigb[CR]=1), DDR clock period is 5nsmem_sdmode: 0000 0001 0010 0111 0010 0010 0010 0100 : 0x01283334  Twtr=001  (1+1 clocks) data sheet specs 7.5ns for tWTR   Twr=010  (1+2 clocks) data sheet specs 15ns for tWR  Tras=1000 (1+8 clocks) data sheet specs 45ns for tRAS   Trp=011  (1+3 clocks) data sheet specs 16ns for tRPTrcdwr=011  (1+3 clocks) data sheet specs 16ns for tRCDTrcdrd=011  (1+3 clocks) data sheet specs 16ns for tRCD  Tcas=100  (CL=3      ) data sheet specs CL=3 for 400mhzmem_sdaddr: 1:0010 0010 0001 0000 0000 0011 1110 0000 : 0x221003F0    BR=0    (bank,row,col)    RS=10   (13 row)    CS=010  (9 col)	 E=1    (enabled)  CSBA=0000000000 (0x00000000)CSMASK=1111110000 (0xFC000000)            2:0010 0011 0001 0000 0000 0011 1110 0000 : 0x231003F0    BR=0    (bank,row,col)    RS=10   (13 row)    CS=011  (10 col)	 E=1    (enabled)  CSBA=0000000000 (0x00000000)CSMASK=1111110000 (0xFC000000)mem_sdconfiga: 0011 0001 1110 0000 0000 0110 0000 1010 : 0x31E0060A     E=0    (refresh disable)    CE=11   (both clocks enabled)   RPT=00   (1 refresh per cycle)   Trc=011110 (1+30 clocks) data sheet specs 61ns for tRC   REF=0x60A  (1562 clocks) data sheet specs 7.8usmem_sdconfigb: 1:1010 0000 0000 0010 0000 0000 0000 0000 : 0xA002610C               2:1110 0000 0000 0010 0000 0000 0000 0000 : 0xE002610C    CR=1    (1:1)    BW=0    (32bit wide bus)    MT=1    (DDR2)  PSEL=0    (addr 10 for auto precharge)    C2=0    (core lowest priority)    AC=00   (default)    HP=0    (no half-pll mode)    PM=00   (no power modes)CKECNT=00   (n/a)    BB=0    (normal)    DS=1    (full drive strength)    FS=0    (normal)   PDX=01   (2)CKEmin=10   (3)    CB=0    (normal) TXARD=001  (2)    BA=0    (no block)  TXSR=001100 (1+12 * 16=208 > 200 clocks)mem_sdwrmd:Mode Register 0: 0000 0100 0011 0010 : 0x0432   PD=0     Fast Exit   WR=010   3 Clocks  DLL=0     Normal   TM=0     Normal   CL=011   CL=3   BT=0     sequential burst type   BL=010   burst length of 4Mode Register 1: 1:0000 0100 0100 0000 : 0x0440                 2:0000 0100 0000 0000 : 0x0400  OUT=0     Normal drive strength RDQS=0     Disable  DQS=1     Disable  OCD=000   Not supported  RTT=10    150 Ohm termination needed with two ranks populated   AL=00    0  ODS=0     100%  DLL=0     Normal/EnableMode Register 2: 0x0000Mode Register 3: 0x0000 */#define MEM_SDMODE0_DDR2		0x01283334#define MEM_SDMODE1_DDR2		0x01283334#define MEM_SDADDR0_DDR2		0x221003F0#define MEM_SDADDR1_DDR2		0x010FFFFF#define MEM_SDCONFIGA_DDR2	0x11E0060A#define MEM_SDCONFIGB_DDR2	0xA002610C#define MEM_MR0_DDR2		0x00000432#define MEM_MR1_DDR2		0x40000400#define MEM_MR2_DDR2		0x80000000#define MEM_MR3_DDR2		0xC0000000/* * SDCS0 - 128MB DDR2-533 Samsung K4T51163QB-GCD5 (8Mbit x 16 x 4bank x 2devices) * SDCS1 - 128MB DDR2-533 Samsung K4T51163QB-GCD5 (8Mbit x 16 x 4bank x 2devices)With a DDR clock of 198MHz (sdconfigb[CR]=1), DDR clock period is 5nsmem_sdmode: 0000 0001 0010 0111 0010 0010 0010 0100 : 0x01272224  Twtr=001  (1+1 clocks) data sheet specs 10ns for tWTR   Twr=010  (1+2 clocks) data sheet specs 15ns for tWR  Tras=0111 (1+7 clocks) data sheet specs 40ns for tRAS   Trp=010  (1+2 clocks) data sheet specs 15ns for tRPTrcdwr=010  (1+2 clocks) data sheet specs 15ns for tRCDTrcdrd=010  (1+2 clocks) data sheet specs 15ns for tRCD  Tcas=100  (CL=3      ) data sheet specs CL=3 for 400mhzmem_sdaddr: 0010 0011 0001 0000 0000 0011 1110 0000 : 0x231003E0    BR=0    (bank,row,col)    RS=10   (13 row)    CS=011  (10 col)	 E=1    (enabled)  CSBA=0000000000 (0x00000000)CSMASK=1111100000 (0xF8000000)mem_sdconfiga: 0011 0001 0100 0000 0000 0110 0000 1010 : 0x3140060A     E=0    (refresh disable)    CE=11   (both clocks enabled)   RPT=00   (1 refresh per cycle)   Trc=010100 (1+20 clocks) data sheet specs 55ns for tRC, 105ns for tRFC   REF=0x60A  (1546 clocks) data sheet specs 7.8125us intervals (8K rows in 64ms)mem_sdconfigb: 1010 0000 0000 0010 0000 0000 0000 0000 : 0xA012610C    CR=1    (1:1)    BW=0    (32bit wide bus)    MT=1    (DDR2)  PSEL=0    (addr 10 for auto precharge)    C2=0    (core lowest priority)    AC=00   (default)    HP=0    (no half-pll mode)    PM=00   (no power modes)CKECNT=01   (1*16)    BB=0    (normal)    DS=1    (full strength)    FS=0    (normal)   PDX=01   (2)CKEmin=10   (3)    CB=0    (normal) TXARD=001  (2)    BA=0    (no block)  TXSR=001100 (1+12 * 16=208 > 200 clocks)mem_sdwrmd:Mode Register 0: 0000 0100 0011 0010 : 0x0432   PD=0     Fast Exit   WR=010   3 Clocks  DLL=0     Normal   TM=0     Normal   CL=011   CL=3   BT=0     sequential burst type   BL=010   burst length of 4Mode Register 1: 0000 0100 0000 0000 : 0x0440  OUT=0     full strength RDQS=0     Disable  DQS=1     Disable  OCD=000   Not supported  RTT=10    150 Ohm termination needed with two ranks populated   AL=00    0  ODS=0     100%  DLL=0     Normal/EnableMode Register 2: 0x0000Mode Register 3: 0x0000#define MEM_SDMODE0_DDR2		0x01272224#define MEM_SDMODE1_DDR2		0x01272224#define MEM_SDADDR0_DDR2		0x231003E0#define MEM_SDADDR1_DDR2		0x00000000//0x231083E0#define MEM_SDCONFIGA_DDR2	0x1140060A//0x3140060A#define MEM_SDCONFIGB_DDR2	0xA012610C#define MEM_MR0_DDR2		0x00000432#define MEM_MR1_DDR2		0x40000440#define MEM_MR2_DDR2		0x80000000#define MEM_MR3_DDR2		0xC0000000 */#define MEM_400NS			(396 * 4 / 10)#define MEM_1MS			(396 * 1000)/********************************************************************//********************************************************************//********************************************************************//********************************************************************/	.text	.set noreorder	.set mips32	/*	 * Step 1) Establish CPU endian mode.	 * Little Endian	 */	li	t0, AU1200_SYS_ADDR	li	t1, 1	sw	t1, sys_endian(t0)	sync	mfc0	t2, CP0_Config	mtc0	t2, CP0_Config	nop	nop	/*	 * Step 2) Establish Status Register	 * (set BEV, clear ERL, clear EXL, clear IE)	 */	li	t1, 0x00400000	mtc0	t1, CP0_Status	/*	 * Step 3) Establish CP0 Config0